5.1.6 Setting up ITSLM - Manager
The purpose of setup is to create an execution environment.
You can set up either ITSLM - Manager or ITSLM - UR first.
This subsection explains how to set up ITSLM - Manager.
- Organization of this subsection
(1) Before you start
-
Verify that your user account belongs to the OS's Administrators group.
-
Before you start the setup, install the ITSLM - Manager that is to be set up.
For details about the installation, see 5.1.5 Installing ITSLM.
-
Verify that JP1/Base has been installed on the host on which ITSLM - Manager is being installed.
For details about how to install JP1/Base, see the Job Management Partner 1/Base User's Guide.
(2) Procedure
To set up ITSLM - Manager:
-
Create the options file required for setup.
For details about the options file, see jslmmgrsetup (sets up ITSLM - Manager) in 9. Commands.
-
Store the created options file in a desired folder.
Make sure that the absolute path of the options file storage location does not exceed 255 bytes including the options file name (any name).
-
Execute the setup command.
The following shows the setup command that is to be executed:
ITSLM-Manager-installation-folder\mgr\bin\jslmmgrsetup absolute-path-of-options-file
For details about the setup command, see jslmmgrsetup (sets up ITSLM - Manager) in 9. Commands.
When the command terminates normally, ITSLM - Manager setup is complete.
(3) Supplementary information
-
If a firewall has been set up on the host on which ITSLM - Manager has been set up, you must release the port numbers that were specified for the psb_Listen and manager_port definition items in the options file used during setup. If you change the settings in the options file, you must also change the firewall settings, and then check the following:
-
Check if ephemeral ports for communication between ITSLM - Manager and ITSLM - UR and between ITSLM - Manager and the browser have been released.
If they have not been released, set up the firewall to release ephemeral ports or set it up to allow communication from the following programs:
- ITSLM - Manager-installation-folder\mgr\bin\system\jslmmUR.exe
- ITSLM - Manager-installation-folder\mgr\bin\system\jslmmRMI.exe
- ITSLM - Manager-installation-folder\mgr\system\psb\CC\web\bin\cjstartweb.exe
-
Check if the firewall is allowed to communicate with the loopback address of the host where ITSLM - Manager is set up.
-
-
To adjust the time on the host on which ITSLM - Manager has been set up, you must first terminate all ITSLM - Managers and ITSLM - URs. To do this, first stop all services running on the ITSLM - Managers and ITSLM - URs.
It is preferable to adjust ITSLM - Manager's time forward. If ITSLM - Manager's time is set earlier as a result of adjustment (adjusted backward), wait until the amount of time that was adjusted backward has elapsed, and then start ITSLM - Manager and ITSLM - UR. For example, if you moved the computer's time backward by five minutes, wait for at least five minutes before you start ITSLM - Manager.
Note that you can adjust the time of a computer that displays windows used for monitoring at any time, regardless of whether ITSLM - Manager is running.
-
Make sure that you specify a value in the range from 1 to 65535 for the psb_Listen definition item in the options file that is used when the jslmmgrsetup command is executed. If you have specified any other value and then performed the setup, perform setup again using the procedure described below after a setup error has been issued.
-
Correct the Listen property value defined in the file shown below (httpsd.conf) to a value in the range from 1 to 65535:
ITSLM-Manager-installation-folder\mgr\system\psb\httpsd\conf\httpsd.conf
-
Specify a value in the range from 1 to 65535 for the psb_Listen definition item in the jslmmgrsetup command's options file, and then perform setup again.
-
-
If setup fails during upgrading, data in the database might have become corrupted. Therefore, when setup fails during upgrading, take the appropriate corrective action to eliminate the cause, install ITSLM again using the procedure below, and then perform setup:
-
Uninstall the ITSLM that has been installed.
-
Install the previous version of ITSLM.
-
Restore the backup data that was acquired before upgrading.
-
Re-install the new version of ITSLM.
-