Hitachi Dynamic Link Manager ユーザーズガイド(VMware®用)
メッセージID | メッセージテキスト | 説明 |
---|---|---|
KAPL01001-I | HDLMコマンドが正常終了しました。オペレーション名 = aa...aa, 終了時刻 = bb...bb The HDLM command completed normally. Operation name = aa...aa, completion time = bb...bb |
|
KAPL01002-I | HDLMコマンドを開始しました。オペレーション名 = aa...aa The HDLM command started. Operation name = aa...aa |
|
KAPL01003-W | オペレーション名が指定されていません。 No operation name is specified. |
|
KAPL01004-W | オペレーション名が誤っています。オペレーション名 = aa...aa The operation name is invalid. Operation name = aa...aa |
|
KAPL01005-W | パラメタが誤っています。オペレーション名 = aa...aa, パラメタ = bb...bb A parameter is invalid. Operation name = aa...aa, parameter = bb...bb |
|
KAPL01006-W | 必要なパラメタが指定されていません。オペレーション名 = aa...aa A necessary parameter is not specified. Operation name = aa...aa |
|
KAPL01007-W | パラメタが重複して指定されています。オペレーション名 = aa...aa, パラメタ = bb...bb A duplicate parameter is specified. Operation name = aa...aa, parameter = bb...bb |
|
KAPL01008-W | 必要なパラメタ値が指定されていません。オペレーション名 = aa...aa, パラメタ = bb...bb A necessary parameter value is not specified. Operation name = aa...aa, parameter = bb...bb |
|
KAPL01009-W | パラメタ値が誤っています。オペレーション名 = aa...aa, パラメタ = bb...bb, パラメタ値 = cc...cc, 有効値 = dd...dd A parameter value is invalid. Operation name = aa...aa, parameter = bb...bb, parameter value = cc...cc, Valid value = dd...dd |
|
KAPL01012-E | HDLMマネージャとの接続に失敗しました。オペレーション名 = aa...aa Could not connect the HDLM manager. Operation name = aa...aa |
|
KAPL01013-E | HDLMコマンド内部処理で障害が発生しました。オペレーション名 = aa...aa, 詳細 = bb...bb An error occurred in internal processing of the HDLM command. Operation name = aa...aa details = bb...bb |
|
KAPL01014-W | HDLMコマンドを実行する権限がありません。オペレーション名 = aa...aa No authority to execute the HDLM command. Operation name = aa...aa |
|
KAPL01016-W | 操作対象のCHAポートがありませんでした。オペレーション名 = aa...aa The target CHA port was not found. Operation name = aa...aa |
|
KAPL01018-W | 操作対象のデバイスがありませんでした。オペレーション名 = aa...aa The target device was not found. Operation name = aa...aa |
|
KAPL01019-W | 操作対象のパスがありませんでした。オペレーション名 = aa...aa The target path was not found. Operation name = aa...aa |
|
KAPL01021-E | メモリ不足によりHDLMコマンドが実行できません。 Cannot execute the HDLM command due to insufficient memory. |
|
KAPL01024-W | 同時に指定できないパラメタが指定されています。オペレーション名 = aa...aa, パラメタ = bb...bb The specified parameters cannot be specified at the same time. Operation name = aa...aa, parameters = bb...bb |
|
KAPL01036-E | パスの回復に失敗しました。PathID = aa...aa The Offline path cannot be placed online. PathID = aa...aa |
|
KAPL01039-W | HDLMコマンドのonlineオペレーションの処理中に,状態をOnlineにできないパスを検出しました。 PathID = aa...aa。 onlineオペレーションの処理を継続しますか? [y/n]: During the online operation processing of the HDLM command, a path that cannot be placed in the Online status was detected. PathID = aa...aa Would you like to continue the processing of the online operation? [y/n]: |
|
KAPL01040-W | 入力の値が不正です。再入力してください。 [y/n]: The entered value is invalid. Re-enter [y/n]: |
|
KAPL01041-E | 入力の値が不正です。オペレーションを中断します。オペレーション名 = aa...aa The entered value is invalid. The operation stops. Operation name = aa...aa |
|
KAPL01044-W | パラメタ値が重複して指定されています。オペレーション名 = aa...aa, パラメタ = bb...bb, パラメタ値 = cc...cc A duplicate parameter value is specified. Operation name = aa...aa, parameter = bb...bb, parameter value = cc...cc |
|
KAPL01045-W | パラメタ値が多過ぎます。オペレーション名 = aa...aa,パラメタ = bb...bb,パラメタ値 = cc...cc Too many parameter values are specified. Operation name = aa...aa, parameter = bb...bb, parameter value = cc...cc |
|
KAPL01048-W | ヘルプ情報が存在しません。オペレーション名 = aa...aa Help information cannot be found. Operation name = aa...aa |
|
KAPL01049-I | オペレーションを開始します。オペレーション名 = aa...aa。よろしいですか? [y/n]: Would you like to execute the operation? Operation name = aa...aa [y/n]: |
|
KAPL01050-I | 指定されたパスをOnlineにします。よろしいですか? [y/n]: The currently selected paths will be changed to the Online status. Is this OK? [y/n]: |
|
KAPL01052-I | 指定されたパスをOffline(C)にします。よろしいですか? [y/n]: The currently selected paths will be changed to the Offline(C) status. Is this OK? [y/n]: |
|
KAPL01053-I | 指定されたパスがOffline(C)になってもよい場合はyを入力してください。そうでない場合はnを入力してください。 [y/n]: If you are sure that there would be no problem when the path is placed in the Offline(C) status, enter y. Otherwise, enter n. [y/n]: |
|
KAPL01054-W | HDLMコマンドのofflineオペレーションの処理中に,状態をOffline(C)にできないパスを検出しました。PathID = aa...aa。offlineオペレーションの処理を継続しますか? [y/n]: During the offline operation processing of the HDLM command, a path that cannot be placed in the Offline(C) status was detected. PathID = aa...aa Would you like to continue the processing of the offline operation? [y/n]: |
|
KAPL01055-I | 指定されたaa...aaを通る全てのパスをOffline(C)にします。よろしいですか? [y/n]: All the paths which pass the specified aa...aa will be changed to the Offline(C) status. Is this OK? [y/n]: |
|
KAPL01056-I | 指定されたaa...aaを通る全てのパスがOffline(C)になってもよい場合はyを入力してください。そうでない場合はnを入力してください。 [y/n]: If you are sure that there would be no problem when all the paths which pass the specified aa...aa are placed in the Offline(C) status, enter y. Otherwise, enter n. [y/n]: |
|
KAPL01057-I | 指定されたaa...aaを通る全てのパスをOnlineにします。よろしいですか? [y/n]: All the paths which pass the specified aa...aa will be changed to the Online status. Is this OK? [y/n]: |
|
KAPL01058-W | 不要なパラメタ値が指定されました。オペレーション名 = aa...aa,パラメタ = bb...bb,パラメタ値 = cc...cc The specified parameter value is not needed. Operation name = aa...aa, parameter = bb...bb, parameter value = cc...cc |
|
KAPL01059-W | パラメタaa...aaにパラメタ値bb...bbを指定した場合,同時にパラメタcc...ccは指定できません。オペレーション名 = dd...dd Cannot specify the parameter cc...cc at the same time if you specify parameter aa...aa and parameter value bb...bb. Operation name = dd...dd |
|
KAPL01060-I | ユーザの指定により,オペレーションの処理を中断しました。オペレーション名 = aa...aa The user terminated the operation. Operation name = aa...aa |
|
KAPL01061-I | aa...aa本のパスをbb...bbにしました。失敗したパス = cc...cc本。オペレーション名 = dd...dd aa...aa path(s) were successfully placed bb...bb; cc...cc path(s) were not. Operation name = dd...dd |
|
KAPL01063-I | 操作対象のパスは既にaa...aaです。 The target path(s) are already aa...aa. |
|
KAPL01068-I | ライセンスキーを入力して下さい: Enter a license key: |
|
KAPL01069-W | 入力されたライセンスキーが不正です。 The entered license key is invalid. |
|
KAPL01070-E | 入力されたライセンスキーが不正です。ライセンスの更新を中断します。 The entered license key is invalid. Renewal of the license key will now stop. |
|
KAPL01071-I | 永久ライセンスがインストールされました。 The permanent license was installed. |
|
KAPL01072-I | 非常ライセンスがインストールされました。期限満了日はaa...aaです。 The emergency license was installed. The license expires on aa...aa. |
|
KAPL01073-E | 一時ライセンスの期限が切れています。 The temporary license expired. |
|
KAPL01074-E | 非常ライセンスの期限が切れています。 The emergency license expired. |
|
KAPL01075-E | HDLM内で重大エラーが発生しました。システム環境が不正です。 A fatal error occurred in HDLM. The system environment is invalid. |
|
KAPL01076-I | 永久ライセンスがインストールされています。 The permanent license has been installed. |
|
KAPL01081-E | ライセンスキーファイルが不正です。ファイル名 = aa...aa The license key file is invalid. File name = aa...aa |
|
KAPL01082-E | インストール可能なライセンスキーがライセンスキーファイル内にありません。ファイル名 = aa...aa There is no installable license key in the license key file. File name = aa...aa |
|
KAPL01083-I | ライセンスキーファイルがありません。ファイル名 = aa...aa There is no license key file. File name = aa...aa |
|
KAPL01084-W | ライセンスキーファイルの削除に失敗しました。ファイル名 = aa...aa An attempt to delete the license key file has failed. File name = aa...aa |
|
KAPL01088-W | 同時に指定できないパラメタ値が指定されています。オペレーション名 = aa...aa, パラメタ = bb...bb, パラメタ値 = cc...cc The specified parameter values cannot be specified at the same time. Operation name = aa...aa, parameter = bb...bb, parameter values = cc...cc |
|
KAPL01089-E | HDLMコマンドのset -licオペレーションまたは,更新インストール時におけるライセンスの更新が同時に実行されました。 One of the following was executed at the same time as an HDLM command set -lic operation: another set -lic operation, or an update of the license for an update installation. |
|
KAPL01095-E | HDLMのバージョン情報の取得に失敗しました。詳細 = aa...aa An attempt to acquire the HDLM version information has failed. details = aa...aa |
|
KAPL01096-E | Service Packのバージョン情報の取得に失敗しました。詳細 = aa...aa An attempt to acquire the Service Pack version information has failed. details = aa...aa |
|
KAPL01100-I | aa...aa |
|
KAPL01101-W | 操作対象のHBAポートがありませんでした。オペレーション名 = aa...aa The target HBA port was not found. Operation name = aa...aa |
|
KAPL01102-I | 指定されたaa...aaポートを通る全てのパスをOffline(C)にします。よろしいですか? [y/n]: All the paths which pass the specified aa...aa port will be changed to the Offline(C) status. Is this OK? [y/n]: |
|
KAPL01103-I | 指定されたaa...aaポートを通る全てのパスがOffline(C)になってもよい場合はyを入力してください。そうでない場合はnを入力してください。 [y/n]: If you are sure that there would be no problem when all the paths which pass the specified aa...aa port are placed in the Offline(C) status, enter y. Otherwise, enter n. [y/n]: |
|
KAPL01104-I | 指定された aa...aaポートを通る全てのパスをOnlineにします。よろしいですか? [y/n]: All the paths which pass the specified aa...aa port will be changed to the Online status. Is this OK? [y/n]: |
|
KAPL01107-I | オペレーションを開始します。オペレーション名 = set。本オペレーションを実行すると,LU個別に設定されているロードバランス種別が無効になります。よろしいですか? [y/n]: The load balancing type specified for individual LUs will become invalid when this operation is executed. Do you want to execute the operation anyway? Operation name = set [y/n]: |
|
KAPL01117-W | 監査ログ設定ファイルの読み込み処理でエラーが発生しました。 An error occurred during processing to read the audit log configuration file. |
|
KAPL01118-W | 監査ログの出力処理でエラーが発生しました。 An error occurred during processing to output the audit log configuration file. |
|
KAPL01119-W | 監査ログの出力処理でエラーが発生しました。 An error occurred during processing to output the audit log configuration file. |
|
KAPL01120-W | ストレージシステムのモデルIDを表示できませんでした。 詳細 = aa...aa, bb...bb A storage system model ID could not be displayed. Details = aa...aa, bb...bb |
|
KAPL01135-W | ホスト接続オプションが誤っています。オプション = aa...aa A host connection option is invalid. Option = aa...aa |
|
KAPL01136-W | 同時に指定できないホスト接続オプションが指定されています。オプション = aa...aa The specified host connection options cannot be specified at the same time. Options = aa...aa |
|
KAPL01138-W | ホスト接続オプション-lを指定したときはaa...aaオペレーションは実行できません。 The aa...aa operation cannot be executed if the host connection option -l is specified. |
|
KAPL01139-W | ホスト接続オプションaa...aaを指定したときはbb...bbパラメタは指定できません。 The parameter bb...bb cannot be specified if the host connection option aa...aa is specified. |
|
KAPL01140-W | ホスト接続オプションが重複して指定されています。オプション = aa...aa A duplicate host connection option is specified. Option = aa...aa |
|
KAPL01141-W | ホスト接続オプションに必要なオプション値が指定されていません。オプション = aa...aa There is no value specified for the host connection option. Option = aa...aa |
|
KAPL01142-W | ホスト接続オプションを省略したときはaa...aaパラメタは指定できません。 The parameter aa...aa cannot be specified if you omitted the host connection option. |
|
KAPL01143-W | ホスト接続オプションaa...aaはオプション値を指定できません。 The host connection option value cannot be specified. Option = aa...aa |
|
KAPL01144-W | HDLMコマンドがVMware vSphere CLIのコマンドプロンプトで実行されていません。 The HDLM command was not executed from the VMware vSphere CLI command prompt. |
|
KAPL01146-I | パスが指定されていないので,Offline(C),Offline(E) のパスをOnline にします。よろしいですか? [y/n]: Because no path has been selected among the currently displayed paths, the paths in the Offline(C) and Offline(E) statuses will be changed to the Online status. Is this OK?[y/n]: |
|
KAPL01147-I | aa...aa 本のパスをbb...bb にしました。失敗したパス = cc...cc 本。操作対象のパス数 = dd...dd。オペレーション名 = ee...ee aa...aa path(s) were successfully placed bb...bb; cc...cc path(s) were not. Number of target paths = dd...dd, operation name = ee...ee |
|
KAPL01148-E | 指定されたサーバとの接続に失敗しました。オペレーション名 = aa...aa An attempt to connect to the specified server has failed. Operation name = aa...aa |
|
KAPL01149-E | HDLMドライバ(HTI_HDLM_SATP)との接続に失敗しました。オペレーション名 = aa...aa An attempt to connect to the HDLM driver (HTI_HDLM_SATP) has failed. Operation name = aa...aa |
|
KAPL01150-E | VMware vSphere CLIがインストールされていないため,HDLM コマンドが実行できません。 The HDLM command cannot be executed because the VMware vSphere CLI is not installed. |
|
KAPL01151-E | HDLM Windows版がインストールされているため,HDLM コマンドが実行できません。 HDLM commands cannot be executed because HDLM for Windows is installed. |
|
KAPL01152-E | パスの構成が変更中のため,オペレーションを中断しました。オペレーション名 = aa...aa The operation was canceled because the path configuration is being changed. Operation name = aa...aa |
|
KAPL01153-W | HDLMコマンドのofflineオペレーションの処理中に,状態をOffline(C)にできないパスを検出しました。PathID = aa...aa During the offline operation processing of the HDLM command, a path that cannot be placed in the Offline(C) status was detected. PathID = aa...aa |
|
KAPL01154-W | すでにシステム単位で(aa...aa)設定済みです。 The dynamic I/O path control function is already set to aa...aa for the system. |
|
KAPL01155-W | すでにストレージ単位で(aa...aa)設定済みです。 The dynamic I/O path control function is already set to aa...aa for storage. |
|
KAPL01158-E | 指定したストレージは動的パス制御が適用できないストレージ装置です。 Dynamic I/O path control cannot be applied to the specified storage. |
|
KAPL01174-W | 物理ストレージの表示が無効の場合,パラメタ-itemにパラメタ値aa...aaは指定できません。 If the Physical Storage View is disabled, the parameter value aa...aa cannot be specified for the -item parameter. |
|
KAPL01175-W | 物理ストレージの表示が有効の場合,パラメタ-itemにパラメタ値aa...aaは指定できません。 If the Physical Storage View is enabled, the parameter value aa...aa cannot be specified for the -item parameter. |
|
KAPL01176-I | 操作対象のパスに,Offline状態のパスがありました。Offline状態のパスは,ストレージシステムの設定が反映されていません。 Some of the target paths are in the offline status. Storage system settings are not refreshed for offline paths. |
|
KAPL01177-W | ストレージシステムの設定の取得に失敗したパスがありました。 HDLM failed to acquire storage system settings for some paths. |
|
KAPL01178-E | ストレージシステムの設定の反映に失敗しました。詳細 = aa...aa, bb…bb HDLM failed to refresh the storage system settings. Details = aa...aa, bb…bb |
|
KAPL01180-E | HDLMのインストール後に,ESXiホストが再起動されていません。 After HDLM was installed, the ESXi host was not restarted. |
|
KAPL01181-E | HDLMドライバが正しくインストールされていません。 The HDLM driver is not installed correctly. |
|
KAPL01182-E | VMware PowerCLIがインストールされていないため,HDLM コマンドが実行できません。 The HDLM command cannot be executed because VMware PowerCLI is not installed. |
|
KAPL01183-E | VMware PowerCLIの設定がHDLMコマンドを実行できる設定ではありません。 The HDLM command cannot be executed because the VMware PowerCLI settings are not configured properly. |
|
KAPL01184-E | 操作対象のホストが指定されていません。 The target host was not specified. |
|
All Rights Reserved. Copyright© 2014, 2023, Hitachi, Ltd.