Job Management Partner 1/Automatic Job Management System 3 - Web Operation Assistant Description, Operator's Guide and Reference

[Contents][Glossary][Index][Back][Next]

6.4.6 Settings frame (Items displayed in status list)

This frame sets the items to be displayed in the status list.

The following figure shows the frame for setting the items to be displayed in the status list.

Figure 6-23 Frame for setting the items to be displayed in the status list

[Figure]

Organization of this subsection
(1) Host name
(2) Service name
(3) Unit name
(4) Type
(5) Comment
(6) Executing ID
(7) Status
(8) Hold
(9) Delay status
(10) Time when start delayed
(11) Time when end delayed
(12) Return value
(13) Change plan
(14) Scheduled start time
(15) Start time
(16) End time
(17) Target host
(18) Required time
(19) Apply button
(20) Default button

(1) Host name

(a) Display type

Select the radio button to specify whether or not to display the column for the host name.

(b) Item width

Select one of the following radio buttons for the width of the item to be displayed:

If you select Automatic, the width of the item will be set to a minimum value that prevents cause the contents of the cell from wrapping around.

If you select Specified width, specify the value in the range from 1 to 1,000 (unit: pixel). If the contents of the item are longer than the specified width, the contents will wrap around to fit in the cell.

Supplementary note
If the specified width is smaller than the width of one character, the contents of the cell will wrap around by one character. However, strings of alphanumeric characters will not wrap around.

(2) Service name

(a) Display type

Select the radio button to specify whether or not to display the column for the service name.

(b) Item width

Select one of the following radio buttons for the width of the item to be displayed:

If you select Automatic, the width of the item will be set to a minimum value that prevents the contents of the cell from wrapping around.

If you select Specified width, specify the value in the range from 1 to 1,000 (unit: pixel). If the contents of the item are longer than the specified width, the contents will wrap around to fit in the cell.

Supplementary note
If the specified width is smaller than the width of one character, the contents of the cell will wrap around by one character. However, strings of alphanumeric characters will not wrap around.

(3) Unit name

(a) Display type

Select the radio button to specify whether or not to display the column for the unit name.

(b) Item width

Select one of the following radio buttons for the width of the item to be displayed:

If you select Automatic, the width of the item will be set to a minimum value that prevents the contents of the cell from wrapping around.

If you select Specified width, specify the value in the range from 1 to 1,000 (unit: pixel). If the contents of the item are longer than the specified width, the contents will wrap around to fit in the cell.

Supplementary note
If the specified width is smaller than the width of one character, the contents of the cell will wrap around by one character. However, strings of alphanumeric characters will not wrap around.

(c) Display method

Select one of the following radio buttons for the display method of the unit name:

When you select Complete display, the complete name of the unit will be displayed.

When you select Simple display, the unit path name from the top to the higher-order unit will not be displayed.

(d) Hyperlink

Use the radio button to specify whether or not to display the unit name as a hyperlink.

(4) Type

(a) Display type

Select the radio button to specify whether or not to display the column for the unit type.

(5) Comment

(a) Display type

Select the radio button to specify whether or not to display the comment rows.

(b) Item width

Select one of the following radio buttons for the width of the item to be displayed:

If you select Automatic, the width of the item will be set to a minimum value that prevents the contents of the cell from wrapping around.

If you select Specified width, specify the value in the range from 1 to 1,000 (unit: pixel). If the contents of the item are longer than the specified width, the contents will wrap around to fit in the cell.

Supplementary note
If the specified width is smaller than the width of one character, the contents of the cell will wrap around by one character. However, strings of alphanumeric characters will not wrap around.

(6) Executing ID

(a) Display type

Select the radio button to specify whether or not to display the column for the executing ID.

(7) Status

(a) Display type

Select the radio button to specify whether or not to display the column for the status.

(8) Hold

(a) Display type

Select the radio button to specify whether or not to display the column for the hold setting.

(9) Delay status

(a) Display type

Select the radio button to specify whether or not to display the column for the delay status.

(10) Time when start delayed

(a) Display type

Select the radio button to specify whether or not to display the column for the time when start delayed.

(11) Time when end delayed

(a) Display type

Select the radio button to specify whether or not to display the column for the time when end delayed.

(12) Return value

(a) Display type

Select the radio button to specify whether or not to display the column for the return value.

(13) Change plan

(a) Display type

Select the radio button to specify whether or not to display the column for the change plan.

(14) Scheduled start time

(a) Display type

Select the radio button to specify whether or not to display the column for the scheduled start time.

(15) Start time

(a) Display type

Select the radio button to specify whether or not to display the column for the start time.

(16) End time

(a) Display type

Select the radio button to specify whether or not to display the column for the end time.

(17) Target host

(a) Display type

Select the radio button to specify whether or not to display the column for the target host name.

(b) Item width

Select one of the following radio buttons for the width of the item to be displayed:

If you select Automatic, the width of the item will be set to a minimum value that prevents the contents of the cell from wrapping around.

If you select Specified width, specify the value in the range from 1 to 1,000 (unit: pixel). If the contents of the item are longer than the specified width, the contents will wrap around to fit in the cell.

Supplementary note
If the specified width is smaller than the width of one character, the contents of the cell will wrap around by one character. However, strings of alphanumeric characters will not wrap around.

(18) Required time

(a) Display type

Select the radio button to specify whether or not to display the column for the required time.

(19) Apply button

Clicking this button saves the settings displayed in the frame.

The changes in the settings take effect when you return to the Monitor window by clicking the Return to Status View hyperlink in the item selection frame or when you log on next time.

If you specify that all of the items are not to be displayed, an error message will be displayed when this button is clicked.

(20) Default button

Clicking this button returns the settings displayed in the frame to the defaults (for details about the defaults, see 4.3 Environment settings changeable in the User Environment Settings window). Clicking this button just changes the displayed settings, and does not save them. Click the Apply button to save the settings.

[Contents][Back][Next]

[Trademarks]

Copyright (C) 2010, Hitachi, Ltd.
Copyright (C) 2010, Hitachi Software Engineering Co., Ltd.