Job Management Partner 1/Automatic Job Management System 3 Configuration Guide 1
As a protection against failures during live operation, JP1/AJS3 can check for problems in the definition of a job before live operation of the job starts. This subsection describes how to set up this function.
- Organization of this subsection
- (1) Procedure for setting up the function
- (2) Procedure for changing the function settings
- (3) Environment setting parameters
(1) Procedure for setting up the function
To set up the JP1/AJS3 definition pre-check function:
- Execute the following command:
For JP1/AJS3 - Manager:
For JP1/AJS3 - Agent:
#/opt/jp1ajs2/bin/ajschksetup -m -a
For details about the ajschksetup command, see ajschksetup in 2. Commands Used during Setup in the manual Job Management Partner 1/Automatic Job Management System 3 Command Reference 2.
#/opt/jp1ajs2/bin/ajschksetup -a
- Start the JP1/AJS3 Check Manager service and the JP1/AJS3 Check Agent service.
The following shows the commands to be executed.
For JP1/AJS3 - Manager:
For JP1/AJS3 - Agent:
#/opt/jp1ajs2/bin/ajschkstart -m -a
For details about the ajschkstart command, see ajschkstart (UNIX only) in 2. Commands in the manual Job Management Partner 1/Automatic Job Management System 3 Command Reference 1.
#/opt/jp1ajs2/bin/ajschkstart -a
(2) Procedure for changing the function settings
To change the settings of the JP1/AJS3 definition pre-check function:
- Stop the JP1/AJS3 Check Manager service and the JP1/AJS3 Check Agent service.
The following shows the commands to be executed.
For JP1/AJS3 - Manager:
For JP1/AJS3 - Agent:
#/opt/jp1ajs2/bin/ajschkstop -m -a
For details about the ajschkstop command, see ajschkstop (UNIX only) in 2. Commands in the manual Job Management Partner 1/Automatic Job Management System 3 Command Reference 1.
#/opt/jp1ajs2/bin/ajschkstop -a
- Execute the following command to set the environment setting parameters described in (3) below:
jajs_config -k definition-key "parameter-name-1"=value-1 ["parameter-name-2"=value-2] ["parameter-name-3"=value-3] ["parameter-name-4"=value-4] ["parameter-name-5"=value-5]- Start the services that you stopped in step 1.
The following shows the commands to be executed.
For JP1/AJS3 - Manager:
For JP1/AJS3 - Agent:
#/opt/jp1ajs2/bin/ajschkstart -m -a
The new settings are applied.
#/opt/jp1ajs2/bin/ajschkstart -a
(3) Environment setting parameters
Table 14-47 Environment setting parameters used to specify the settings of the JP1/AJS3 definition pre-check function
No. Definition key Environment setting parameter Explanation 1 [JP1_DEFAULT\JP1AJS2\CHECK] "AJSCHK_CHECKFILE"#= Specifies the name of the file where the definition pre-check results will be stored. 2 "AJSCHK_LOGDIR"= Specifies the name of the definition check log directory. 3 "AJSCHK_LOGSIZE"= Specifies the size of the definition check log files. 4 "AJSCHK_TRACELOGFILE"= Specifies the name of the trace log file for the definition pre-check function. 5 "AJSCHK_CHARCODE"= Specifies the character encoding used to display job information and the definition pre-check results.
- #:
- This parameter can be set only in JP1/AJS3 - Manager.
For details about the definition of these environment setting parameters, see the following:
- 2.5(1) AJSCHK_CHECKFILE in the Job Management Partner 1/Automatic Job Management System 3 Configuration Guide 2
- 2.5(2) AJSCHK_LOGDIR in the Job Management Partner 1/Automatic Job Management System 3 Configuration Guide 2
- 2.5(3) AJSCHK_LOGSIZE in the Job Management Partner 1/Automatic Job Management System 3 Configuration Guide 2
- 2.5(4) AJSCHK_TRACELOGFILE in the Job Management Partner 1/Automatic Job Management System 3 Configuration Guide 2
- 2.5(5) AJSCHK_CHARCODE in the Job Management Partner 1/Automatic Job Management System 3 Configuration Guide 2
Copyright (C) 2009, 2010, Hitachi, Ltd.
Copyright (C) 2009, 2010, Hitachi Solutions, Ltd.