8.5 KAPL05001~KAPL06000
この節で説明するメッセージの言語種別には,英語,または日本語が選択できます。デフォルトでは,英語のメッセージが出力されます。メッセージの言語種別は,LANG環境変数の値に従います。LANG環境変数の値と,出力メッセージの言語種別の対応を次の表に示します。
対象OS |
LANG環境変数の値 |
出力メッセージの言語種別 |
---|---|---|
Red Hat Enterprise Linux |
ja_JP.UTF-8 |
日本語(UTF-8コード) |
ja_JP.UTF-8以外 |
英語(ASCIIコード) |
|
SUSE LINUX Enterprise Server |
ja_JP.eucJP |
日本語(EUCコード) |
ja_JP.eucJP以外 |
英語(ASCIIコード) |
- 注
LC_ALL環境変数関数やLC_CTYPE環境変数に,LANG環境変数で指定した以外の言語種別を指定していないか確認してください。LC_ALL環境変数関数やLC_CTYPE環境変数と,LANG環境変数に指定された言語種別が異なる場合は,英語のメッセージが出力されます。この注意事項は,HDLMがサポートするすべてのLinuxが対象となります。
メッセージID |
メッセージテキスト |
説明 |
---|---|---|
KAPL05003-I |
Disk(aa...aa),Partition(bb...bb)へのHDLMドライバ(フィルタ部)のアタッチに成功しました。 The HDLM driver (filter component) was successfully attached to Disk (aa...aa), Partition (bb...bb). |
|
KAPL05008-E |
メモリ確保に失敗しました。(aa...aa:bb...bb) DLMgetrasユティリティを実行して,障害情報を購入元会社または保守会社に連絡してください。 Could not allocate memory. (aa...aa:bb...bb) Execute the DLMgetras utility to collect error information, and then contact your vendor or maintenance company. Refer to the HDLM User's Guide for instructions how to execute the DLMgetras utility. |
|
KAPL05011-E |
Disk(aa...aa),Partition(bb...bb)へのHDLMドライバ(フィルタ部)のアタッチに失敗しました。(cc...cc:dd...dd) DLMgetrasユティリティを実行して,障害情報を購入元会社または保守会社に連絡してください。 Could not attach the HDLM driver (filter component) to Disk (aa...aa), Partition (bb...bb). (cc...cc:dd...dd) Execute the DLMgetras utility to collect error information, and then contact your vendor or maintenance company. Refer to the HDLM User's Guide for instructions how to execute the DLMgetras utility. |
|
KAPL05014-I |
デバイスオブジェクト(aa...aa)をパス(bb...bb)として登録しました。 The device object (aa...aa) was registered as the path (bb...bb). |
|
KAPL05018-W |
パス(aa...aa)でのFO処理が失敗しました。(bb...bb:cc...cc) aa...aaのパス接続状態を確認してください。パス接続状態に問題が無い場合,DLMgetrasユティリティを実行して,障害情報を購入元会社または保守会社に連絡してください。 The FO processing in the path (aa...aa) failed. (bb...bb:cc...cc) Check the connection status of the path aa...aa. If there is no problem with the connection status, execute the DLMgetras utility to collect error information, and then contact your vendor or maintenance company. Refer to the HDLM User's Guide for instructions how to execute the DLMgetras utility. |
|
KAPL05019-I |
パス(aa...aa)でのFO処理が完了しました。I/O要求はパス(bb...bb)で処理されました。 The FO processing in the path (aa...aa) finished. The I/O request was processed in the path (bb...bb). |
|
KAPL05020-I |
IOCTL(aa...aa)の処理を開始します。 Processing of IOCTL(aa...aa) will now start. |
|
KAPL05021-I |
IOCTL(aa...aa)の処理は正常に完了しました。 Processing of IOCTL(aa...aa) completed normally. |
|
KAPL05023-E |
IOCTL(aa...aa)の処理に失敗しました。(bb...bb:cc...cc) HDLMマネージャやHDLMコマンドのメッセージを確認して,対処してください。適切な対処方法が不明な場合は,DLMgetrasユティリティを実行して,障害情報を購入元会社または保守会社に連絡してください。 Could not process the IOCTL(aa...aa). (bb...bb:cc...cc) Check the message of the HDLM command or the HDLM manager, and then take the appropriate action. If you do not know the appropriate action, execute the DLMgetras utility to collect error information, and then contact your vendor or maintenance company. Refer to the HDLM User's Guide for instructions how to execute the DLMgetras utility. |
|
KAPL05701-I |
HDLM version aa...aa Build bb...bb cc...cc dd...dd ee...ee |
|
KAPL05704-E |
HDLMデバイスのLDEV情報が変更されました。HCTL = aa...aa bb...bb cc...cc dd...dd The LDEV information for an HDLM device has changed. HCTL value = aa...aa bb...bb cc...cc dd...dd |
|
KAPL05708-E |
メモリ確保のリトライをaa...aa回実行しましたが失敗しました。(bb...bb:cc...cc) The system retried to allocate memory aa...aa times, but the retries failed. (bb...bb:cc...cc) |
|
KAPL05709-I |
メモリ確保のリトライ回数はaa...aaです。 The system will retry to allocate memory aa...aa times. |
|
KAPL05711-I |
SCSI INQUIRYのタイムアウト値とリトライ回数を設定しました。タイムアウト値 = aa...aa, リトライ回数 = bb...bb The timeout value and retry count of SCSI INQUIRY has been set. (timeout value = aa...aa, retry count = bb...bb) |
|
KAPL05713-I |
Reservation Keyの登録状態の確認を開始します。 The registration status of the reservation key will now be checked. |
|
KAPL05714-I |
Reservation Keyの登録状態の確認を実行しました。 The registration status of the reservation key was checked. |
|
KAPL05732-I |
パス(aa...aa)でフラグ(bb...bb),状態(cc...cc)のI/Oを処理しました。 The I/O of status (cc...cc) and flag (bb...bb) was processed by using path (aa...aa). |
|
KAPL05819-I |
保守用トレースデータです。:aa...aa bb...bb cc...cc dd...dd Data for maintenance: aa...aa bb...bb cc...cc dd...dd. |
|