3.5.8 Monitoring of multiple sites
The content displayed in the [Operation Status] area of integrated operation viewer running on lower manager of each office can be integrated and displayed in the [Operation Status] area of integrated operation viewer running on the Integrated Manager. IM management node that was added in version 13-00 or later can also be consolidated and displayed in the same way.
In addition, JP1 events issued by a site's systems are mapped to IM management node displayed in the Integrated Manager's integrated operation viewer.
- Organization of this subsection
(1) Prerequisites
The prerequisites are as follows:
-
The monitored server must have a unique host name and IP address within the same customer site.
If you monitor a monitored server on the Intelligent Integrated Management Infrastructure, the Integrated Monitoring Server cannot uniquely identify the monitored server with the same name for multiple sites. Therefore, it is not possible to monitor as separate nodes on the tree.
-
Intelligent Integrated Management Base, Integration Manager Infrastructure service is running on the base or relay manager host when the base or relay manager host and IM management node under it are reflected on the Integration Manager host with one of the following:
-
Run jddcreatetree and jddupdatetree commands on the Integration Manager host.
-
Executes IM management node creation function from integrated operation viewer.
-
-
The following settings are the same for the Integration Manager host and the base or relay manager host.
-
Intelligent Integrated Management Base port-number
-
http or https
-
(2) Displayed in the [Operation Status] area of integrated operation viewer
You can view the configuration information of integrated operation viewer that runs on lower manager of each office by integrating JP1/IM and JP1/Base displayed in the [Status] area of integrated operation viewer that runs on the Integrated Manager. In version 13-00 and later, you can view and consolidate IM managed nodes for JP1/IM-Agent as well.
IM management node of the collaboration product (JP1/AJS or JP1/PFM) specified as target host definition file for configuration collection by the office or relay manager is not displayed in integrated operation viewer running in the integrated manager. To be displayed, you must specify target host definition file for configuration collection in the Integration Manager.
Note that the information displayed in the [Operation Status] area of integrated operation viewer running on the Integration Manager differs depending on the combination of the version of the Integration Manager and the base or relay manager.
|
Combination of manager versions |
Site or Relay Manager |
||
|---|---|---|---|
|
Version 12 |
Version 13 |
||
|
Integration Manager |
Version 12 |
Information obtained from JP1/Base and JP1/IM system configuration information (not including JP1/IM-Agent) |
Information obtained from JP1/Base and JP1/IM system configuration information (not including JP1/IM-Agent) |
|
Version 13 |
Information obtained from JP1/Base and JP1/IM system configuration information (not including JP1/IM-Agent) |
Information obtained from JP1/Base and JP1/IM system configuration information (including JP1/IM-Agent) |
|
JP1 events issued by the local systems are also mapped to IM management node that appears in the Integrated Manager integrated operation viewer.
IM management node data (including SID) managed by the office or relay manager will also be displayed in the Integrated Manager.
(3) Displaying integrated operation viewer in the [related node] tabbed page
The following describes IM management node related to JP1/IM: This is SID when the configuration data exists.
Displays related information in integrated operation viewer running on the Integrated Manager, similar to what you see in integrated operation viewer running on lower manager at your location.
|
from |
to |
Supported versions |
|---|---|---|
|
SID showing JP1/IM-Manager of the Integration Manager host |
SID indicating JP1/IM-Manager of the base or relay manager host |
12-10 or later |
|
SID showing JP1/Base of agent host under the Integration Manager |
12-10 or later |
|
|
SID showing logging of remote witness hosts |
12-10 or later |
|
|
SID indicating JP1/IM-Manager of the base or relay manager host |
A SID showing JP1/Base of agent host under the control of the office or relay manager |
12-10 or later |
|
SID showing logging of remote witness hosts |
12-10 or later |
|
|
SID indicating JP1/IM-Manager# |
JP1/IM agent control base SID |
13-00 or later |
- #
-
For hierarchical configurations, refers to JP1/IM-Manager that directly manages JP1/IM agent control base.
(4) Setting procedure
After setting up a site or relay manager, the Integration Manager host reflects the site or relay manager host and IM management node under it by running jddcreatetree or jddupdatetree commands on the Integration Manager host, or by running IM management node Create Execute function from integrated operation viewer.
(5) Responding to Configuration Changes
- ■To add, modify, and remove IM management node under the office or relay manager host
-
If there is a change in the base or relay manager host, such as adding, changing, or deleting a IM management node, execute the command (jddcreatetree, jddupdatetree) or integrated operation viewer on the integrated manager host to reflect the change to the integrated manager host.
■Adding, modifying, and removing base or relay manager hosts
When adding, changing, or deleting a base or relay manager host, execute the command (jddcreatetree, jddupdatetree) or IM management node creation function from integrated operation viewer on the integration manager host to reflect to the integration manager host.