Preface

This manual describes the settings needed to deploy JP1/Network Node Manager i and JP1/Network Node Manager i Advanced (referred to hereafter as NNMi if there is no difference in the products). It also describes the settings needed to upgrade from version 8 and earlier versions of JP1/Cm2/Network Node Manager (abbreviated as NNM). JP1/Cm2/Network Node Manager is a product name in Japan.

Note also that this manual is intended for all supported operating systems. When there are differences between the NNMi editions on different operating systems, this manual provides separate descriptions for the relevant operating systems.

Organization of this preface

Intended readers
Organization of this manual
Correspondence between previous and current edition manuals
Conventions: Fonts and symbols

■ Intended readers

This manual is intended for users who evaluate and implement a network distributed management system configuration that uses NNMi. This manual assumes that the readers are experienced system administrators, network engineers, and others who are familiar with deploying and managing networks for large-scale systems.

To Page Top

■ Organization of this manual

This manual is organized into the following parts:

PART 1: Preparation: Part 1 explains the preparations required before NNMi is installed, as well as the procedures for installation and uninstallation of NNMi.
PART 2: Introduction: Part 2 explains the minimum settings required for starting network management when NNMi is used.
PART 3: Configuration: Part 3 explains the settings needed for managing a network.
PART 4: Advanced Configuration: Part 4 explains the settings needed to use NNMi functions, such as certification, integration of directory services through NNMi and LDAP, and so on.
PART 5: High Availability Environment Configuration: Part 5 describes support for high availability (HA) clusters and application failover.
PART 6: NNMi Maintenance: Part 6 explains how to back up, restore, and maintain NNMi.
PART 7: Migration: Part 7 explains the operations needed to upgrade NNMi to version 12.
PART 8: Integration with NNMi: Part 8 explains integration of related products with NNMi.
PART 9: Integration: Part 9 explains linkage of NNMi with related products.

To Page Top

■ Correspondence between previous and current edition manuals

The manual listed below have been incorporated into this manual, JP1/Network Node Manager i Setup Guide (3021-3-E02(E)), which has been updated with the enhancements of version 12:

Job Management Partner 1/Consolidated Management 2/Network Node Manager i Installation Guide (3021-3-342-20 (E))

The table below shows the correspondence between the previous and current edition setup guides.

Correspondence between the previous and current edition setup guides

Previous Edition Setup Guide (3021-3-343-20(E))	Current Edition Setup Guide (3021-3-E02(E))
PART 1: Preparation	PART 1: Preparation
1 Hardware and Software Requirements	--
1.1 Supported hardware and software	(Corresponds to 1.1 Checking the hardware and software)
1.2 System configuration (UNIX)	(This section was moved to Appendix A. When NNMi Manpages Cannot Be Displayed (Linux).)
(2. Preinstallation Checklists was inserted from the Installation Guide into the current edition Setup Guide)	1. Preinstallation Checklists
	1.1 Checking the hardware and software
	1.2 Preparing the preinstallation NNMi management server environment
	1.3 Checking for a well-configured DNS
	1.4 Preparing to use the NNMi Quick Start Configuration Wizard
(A. Additional Information About Installation was inserted from the Installation Guide into the current edition Setup Guide)	1.5 Additional information about installation
(3. Installing and Uninstalling NNMi was inserted from the Installation Guide into the current edition Setup Guide)	2 Installing and Uninstalling NNMi
	2.1 Installing NNMi
	2.2 Using the Quick Start Configuration Wizard
	2.3 Licensing NNMi
	2.4 Removing NNMi
(B. Troubleshooting Installation and Initial Startup was inserted from the Installation Guide into the current edition Setup Guide)	2.5 Troubleshooting installation and initial startup
(4. Getting Started with NNMi was inserted from the Installation Guide into the current edition Setup Guide)	Part 2: Introduction
	3. Getting Started with NNMi
	3.1 Accessing NNMi
	3.2 Accessing NNMi Help
	3.3 Configuring network discovery
PART 2: Configuration	PART 3: Configuration
2. General Concepts for Configuration	4. General Concepts for Configuration
3. NNMi Communication	5. NNMi Communications
4. NNMi Discovery	6. NNMi Discovery
5. NNMi State Polling	7. NNMi State Polling
6. NNMi Incidents	8. NNMi Incidents
7. NNMi Console	9. NNMi Console
PART 3: Advanced Configuration	PART 4: Advanced Configuration
8. Working with Certificates for NNMi	10. Working with Certificates for NNMi
9. Configuring the Telnet and SSH Protocols for Use by NNMi	11. Configuring the Telnet and SSH Protocols for Use by NNMi
10. Integrating NNMi with a Directory Service Through LDAP	12. Integrating NNMi with a Directory Service Through LDAP
11. Managing Overlapping IP Addresses in a NAT Environment	13. Managing Overlapping IP Addresses in a NAT Environment
12. NNMi Security and Multi-Tenancy	14. NNMi Security and Multi-Tenancy
13. Global Network Management	15. Global Network Management
14. NNMi IPv6 Management Feature	16. NNMi IPv6 Management Feature
PART 4: High Availability Environment Configuration	PART 5: High Availability Environment Configuration
15. NNMi Data Resilience	17. NNMi Data Resilience
16. Configuring NNMi for Application Failover	18. Configuring NNMi for Application Failover
17. Configuring NNMi in a High Availability Cluster	19. Configuring NNMi in a High Availability Cluster
PART 5: NNMi Maintenance	PART 6: NNMi Maintenance
18. NNMi Backup and Restore Tools	20. NNMi Backup and Restore Tools
19. Maintaining NNMi	21. Maintaining NNMi
20. Changing the NNMi Management Server	22. Changing the NNMi Management Server
21. NNMi Security	23. NNMi Security
PART 6: Migration	PART 7: Migration
22. Upgrading from NNMi Version 9, 10-00, or 10-10	24. Upgrading from NNMi Version 9, 10, or 11
23. Comparison with NNM Version 8 or Earlier	25. Comparison with NNM Version 8 or Earlier
24. Upgrading from NNM Version 8 or Earlier	26. Upgrading from NNM Version 8 or Earlier
--	27. Migrating NNMi from an HP-UX or Solaris Operating System
PART 7: Integration with NNMi	PART 8: Integration with NNMi
25. NNMi Northbound Interface	28. NNMi Northbound Interface
--	PART 9: Integration
--	29. Integration with JP1/IM2 Intelligent Integrated Management Base
--	30. RESTful API
Appendixes	Appendixes
(This appendix was moved from 1.2 System configuration (UNIX).)	A. When NNMi Manpages Cannot Be Displayed (Linux)
(C. List of MIBs Read During a New Installation was inserted from the Installation Guide into the current edition Setup Guide)	B. List of MIBs Read During a New Installation
A. NNMi Environment Variables	C. NNMi Environment Variables
B. The Causal Engine and NNMi Incidents	D. The Causal Engine and NNMi Incidents
C. List of Ports Used by NNMi	E. List of Ports Used by NNMi
D. Version Changes	F. Version Changes
E. Reference Material for This Manual	G. Reference Material for This Manual
F. Glossary	H. Glossary

To Page Top

■ Conventions: Fonts and symbols

The following table explains the text formatting conventions used in this manual:

Text formatting	Convention
Bold	Bold characters indicate text in a window, other than the window title. Such text includes menus, menu options, buttons, radio box options, or explanatory labels. For example: From the File menu, choose Open. Click the Cancel button. In the Enter name entry box, type your name.
Italic	Italic characters indicate a placeholder for some actual text to be provided by the user or system. For example: Write the command as follows: `copy` `source-file` `target-file` The following message appears: `A` `file` `was` `not` `found.` `(file` `=` `file-name)` Italic characters are also used for emphasis. For example: Do not delete the configuration file.
`Monospace`	Monospace characters indicate text that the user enters without change, or text (such as messages) output by the system. For example: At the prompt, enter `dir`. Use the `send` command to send mail. The following message is displayed: `The` `password` `is` `incorrect.`

Text formatting

Convention

Bold

Bold characters indicate text in a window, other than the window title. Such text includes menus, menu options, buttons, radio box options, or explanatory labels. For example:

From the File menu, choose Open.
Click the Cancel button.
In the Enter name entry box, type your name.

Italic

Italic characters indicate a placeholder for some actual text to be provided by the user or system. For example:

Write the command as follows:

copy source-file target-file
The following message appears:

A file was not found. (file = file-name)

Italic characters are also used for emphasis. For example:

Do not delete the configuration file.

Monospace

Monospace characters indicate text that the user enters without change, or text (such as messages) output by the system. For example:

At the prompt, enter dir.
Use the send command to send mail.
The following message is displayed:

The password is incorrect.

The following table explains the symbols used in this manual:

Symbol	Convention
`\|`	In syntax explanations, a vertical bar separates multiple items, and has the meaning of OR. For example: `A\|B\|C` means `A`, or `B`, or `C`.
`{` `}`	In syntax explanations, curly brackets indicate that only one of the enclosed items is to be selected. For example: `{A\|B\|C}` means only one of `A`, or `B`, or `C`.
`[` `]`	In syntax explanations, square brackets indicate that the enclosed item or items are optional. For example: `[A]` means that you can specify `A` or nothing. `[B\|C]` means that you can specify `B`, or `C`, or nothing.
`...`	In coding, an ellipsis (`...`) indicates that one or more lines of coding have been omitted. In syntax explanations, an ellipsis indicates that the immediately preceding item can be repeated as many times as necessary. For example: `A,` `B,` `B,` `...` means that, after you specify `A,` `B,` you can specify `B` as many times as necessary.

To Page Top