Hitachi

JP1 Version 12 JP1/Integrated Management 2 - Manager Configuration Guide


1.18.4 Specifying settings for upgrading(for Windows)

This subsection describes the setup items to be specified during upgrade installation of JP1/IM - Manager.

Organization of this subsection

(1) Executing the Central Scope upgrade command

If you have upgraded JP1/IM - Central Scope from version 8 or earlier, apply the procedure below to execute the upgrade command. Until you execute the upgrade command, JP1/IM - Central Scope will run in the mode that is compatible with the old version of JP1/IM - Central Scope (no new functions can be used).

To execute the Central Scope upgrade command:

  1. Terminate JP1/IM - Manager.

  2. Check the available disk capacity.

    To execute the jp1csverup.bat command in the next step, you will need sufficient free space for the monitoring object database. The monitoring object database includes all the data in the following folder:

    Scope-path\database\jcsdb\

  3. Execute the jp1csverup.bat command.

  4. Execute the jbssetcnf command.

    Whether the following functions are enabled or disabled depends on the settings of the old version of JP1/IM - Central Scope:

    • Completed-action linkage function

    • Monitoring of the maximum number of status change events

    To enable these functions, execute the jbssetcnf command using the files shown in the table below as arguments.

    Table 1‒6: Setting files for enabling functions

    File name

    Description

    action_complete_on.conf

    File for enabling the completed-action linkage function

    evhist_warn_event_on.conf

    File for enabling the JP1 event issuance function when the number of status change events for the monitored object exceeds the maximum value (100)

  5. Start JP1/IM - Manager.

  6. Use JP1/IM - View to connect to JP1/IM - Manager (JP1/IM - Central Scope) to check for any problems.

(2) Updating the automated action definition file

If you have upgraded JP1/IM - Manager from version 11-10 or earlier, apply the procedure below to update the automated action definition file.

If you want to continue using the automated action definition file for version 11-10 or earlier as is, there is no need to perform this procedure.

To update the automated action definition file:

  1. Terminate JP1/IM - Manager.

  2. Execute the following jcadefconv command to update the automated action definition file:

    jcadefconv -i action-definition-file-name-before-conversion -o action-definition-file-name-after-conversion

  3. Rename the file specified for the -o option of the jcadefconv command to actdef.conf, and then move the file to the correct location.

    The path name (including the file name) of the correct location is shown below. Note that you do not need to perform this step if the file name that was specified for the -o option in step 2 is the path name including the file name shown below.

    For a physical host: Console-path\conf\action\actdef.conf

    For a logical host: shared-folder\jp1cons\conf\action\actdef.conf

  4. Start JP1/IM - Manager.

(3) Displaying the source host

When you upgrade JP1/IM - Manager version 09-00 to 09-10, source hosts are not set in the file that defines which items are displayed for event conditions. As a result, even if you enable mapping for source hosts, the list box in the Event conditions section does not display Source host in the Action Parameter Detailed Definitions window. If you want to display Source host in the list box in the Event conditions section of the Action Parameter Detailed Definitions window, you need to add E.JP1_SOURCEHOST in the file that defines which items are displayed for event conditions.

For details about the Action Parameter Detailed Definitions window, see 3.33.1 Action Parameter Detailed Definitions window in the manual JP1/Integrated Management 2 - Manager GUI Reference.

For details about the file that defines which items are displayed for event conditions, see File that defines which items are displayed for event conditions (attr_list.conf) in Chapter 2. Definition Files in the manual JP1/Integrated Management 2 - Manager Command, Definition File and API Reference.

(4) Specifying the event report output format

If you have upgraded from JP1/IM - Manager version 10-50 or earlier, the function for assigning one column to each program-specific extended attribute when event reports are output in CSV format is disabled. To specify whether this function is to be enabled, use the PROGRAM_SPECIFIC_EX_ATTR_COLUMN parameter in the environment definition file for event report output (evtreport.conf). This function is enabled when you perform a new installation. If necessary, configure the environment definition file for event report output.

For details about the environment definition file for event report output, see Environment definition file for event report output (evtreport.conf) in Chapter 2. Definition Files in the manual JP1/Integrated Management 2 - Manager Command, Definition File and API Reference.

(5) Displaying the Start the process automatically when the log file trap service starts check box

If you have upgraded JP1/IM - Manager from version 11-01 or earlier, the Start the process automatically when the log file trap service starts check box is disabled (hidden).

You can use the LOGFILETRAP_AUTO_START_CONTROL parameter in the profile management environment definition file (jp1cf_profile_manager.conf) to specify the enable/disable setting for the Start the process automatically when the log file trap service starts check box. For details, see Profile management environment definition file (jp1cf_profile_manager.conf) in Chapter 2. Definition Files in the manual JP1/Integrated Management 2 - Manager Command, Definition File and API Reference.

(6) Updated agent profile notification function

If you have upgraded JP1/IM - Manager from version 11-01 or earlier, the updated agent profile notification function is disabled.

You can use the AGENT_PROFILE_UPDATE_NOTICE parameter in the profile management environment definition file (jp1cf_profile_manager.conf) to specify the enable/disable setting for the updated agent profile notification function. For details, see Profile management environment definition file (jp1cf_profile_manager.conf) in Chapter 2. Definition Files in the manual JP1/Integrated Management 2 - Manager Command, Definition File and API Reference.

(7) Setting for monitoring logs while remote monitoring is stopped

If you have upgraded JP1/IM - Manager from version 11-01 or earlier, the log data that is output while remote monitoring is stopped is set to be not collected.

You can use the START_OPTION parameter in the remote log trap environment definition file (jp1cf_remote_logtrap.conf) to specify the setting for whether log data that is output while remote monitoring is stopped is to be collected. For details, see Remote log trap environment definition file (jp1cf_remote_logtrap.conf) in Chapter 2. Definition Files in the manual JP1/Integrated Management 2 - Manager Command, Definition File and API Reference.

(8) Upgrading the Intelligent Integrated Management Base (for Windows)

If you are using the Intelligent Integrated Management Base, you can upgrade it as follows:

  1. Terminate JP1/IM - Manager.

  2. Add new settings.

    Add new settings corresponding to the new functions you are going to use.

  3. Start JP1/IM - Manager.

  4. Execute the jddcreatetree command.

  5. Execute the jddupdatetree command in new and rebuilding mode.

Unless you upgrade the Intelligent Integrated Management Base, you cannot use the functionality provided by Intelligent Integrated Management Base 12-50.