3.2.1 Usage example of Add virtual server (LU creation and data store creation) service template
This section provides assumed system configurations and examples of properties to be specified when using the Add virtual server (LU creation and data store creation) service template.
By using this service template, you can create a DP volume on a storage system or a data store on VMware vSphere ESXi (or VMware ESX Server).
Assumed system configuration
This service template assumes the following system configuration:
- Web browser
-
A terminal used to operate JP1/AO. The user uses this terminal to set property values in the service template.
- IT operation automation server
-
A server with JP1/AO and JP1/Base installed.
- vCenter operation server
-
A server with VMware vSphere Power CLI installed.
- vCenter server
-
A server with VMware vCenter Server installed.
- HDvM CLI server
-
A server with Hitachi Device Manager Software CLI installed.
- HDvM server
-
A server with Hitachi Device Manager installed.
- Storage system
-
A storage system managed by Hitachi Device Manager.
- ESX server
-
A server with VMware vSphere ESXi (or VMware ESX Server) installed. This server manages the virtualization server.
Processing flow
-
A user enters property values in the Web browser and submits the service for execution.
-
The IT operation automation server executes automatic processing on the HDvM CLI server and the vCenter operation server.
-
The HDvM CLI server creates one DP volume on the storage system.
-
The HDvM CLI server registers the created volume in the host group of the ESX server.
-
The vCenter operation server allows the ESX server to recognize the added H-LUN.
-
The vCenter operation server adds the data store to the ESX server.
-
From the vCenter operations server, set the FC path to the added data store to Preferred.
Example of specifying property values
To use the Add virtual server (LU creation and data store creation) service template, a user must specify the appropriate property values for the user environment. Specify the property values in the Service Definition dialog box and the Submit Service dialog box.
Property group |
Property name |
Property key |
Description |
Specification example |
---|---|---|---|---|
Virtual system environment information |
Host name of Device Manager CLI server |
hdvm.targetHost |
Specify the host name or IP address of the server where Device Manager CLI is installed. You cannot specify an IPv6 address. |
storagehostCL |
Installation path of Device Manager CLI |
hdvm.cliInstallPath |
Specify the installation path of Device Manager CLI. |
C:\HDVM |
|
Protocol for HDvM communication |
hdvm.hdvmProtocol |
Specify the protocol (http or https) to use when connecting to Device Manager server. |
http |
|
HDvM server host name |
hdvm.hdvmHostName |
Specify the host name or IP address of the Device Manager server. |
storagehostM |
|
Port number for HDvM connection |
hdvm.hdvmPortNumber |
Specify the port number used to connect to the Device Manager server. |
2001 |
|
User name for HDvM connection |
hdvm.hdvmUserName |
Specify the user ID to use when connecting to Device Manager server. |
System |
|
Password for HDvM connection |
hdvm.hdvmPassword |
Specify the password to use when connecting to Device Manager server. |
password |
|
Host name of VMware vCenter control server |
vmware.targetHost |
Specify the host name or IP address of the server (a server with vSphere PowerCLI installed) that will be used to control VMware vCenter. You cannot specify an IPv6 address. |
Vspcli |
|
VMware vCenter server name |
vmware.vCenterServerName |
Specify the host name or IP address of the VMware vCenter server. You cannot specify an IPv6 address. |
Vcenterhost |
|
User name for VMware vCenter Server connection |
vmware.userName |
Specify the user name to use when connecting to the VMware vCenter server. |
User01 |
|
Password for VMware vCenter Server connection |
vmware.password |
Specify the password to use when connecting to the VMware vCenter server. |
password |
|
Protocol for VMware vCenter Server connection |
vmware.protocol |
Specify the protocol to use when connecting to the VMware vCenter server. |
https |
|
Storage information |
Storage system serial number |
hdvm.hdvmSerialNumber |
Specify the serial number of the target storage system. |
123456789 |
Storage system family |
hdvm.hdvmArrayFamily |
Specify the family name of the storage system. You can specify AMS, USP_V, USP_VM, VSP, HUS, HUS VM, or VSP G1000. |
AMS |
Property group |
Property name |
Property key |
Description |
Specification example |
---|---|---|---|---|
Storage information |
DP volume (LU) capacity (in GB) |
hdvm.hdvmCapacity |
Specify the capacity of the DP volume (LU) in GB. |
100 |
DP volume (LU) device number |
hdvm.hdvmDevNumber |
Specify the device number of the DP volume (LU) as a decimal. |
1001 |
|
ID of DP pool |
hdvm.hdvmPoolId |
Specify the pool ID of the pool to be linked with the volume(LU) you are creating. |
10 |
|
Path port name |
hdvm.hdvmPathPortName |
Specify the port name of the path to the DP volume (LU). |
CLT0-A |
|
Host group ID |
hdvm.hdvmDomainId |
Specifies the ID, in decimal or hexadecimal, of the host group where the DP volume (LU) is to be added. In the case of hexadecimal, the prefix "0x" must be used. |
123 |
|
LU number (LUN) |
hdvm.hdvmLun |
Specify the LU number (LUN). |
127 |
|
Virtual environment information |
ESX server name |
vmware.vmHostName |
Specify the ESX server name to be displayed in the Hosts and Clusters inventory view managed by VMware vCenter server. |
ESXhost |
Datastore name |
vmware.dataStoreName |
Specify the datastore name. |
datastore |
|
HBA name |
vmware.hbaName |
Specify the name of the preferred HBA, in the format displayed for the runtime name of the storage adapter in VMware vCenter Server. For example: vmhba0 |
hba |
Related topics