1.3.1 Installation procedure

This subsection explains how to install JP1/IM - Manager and JP1/IM - View.

Organization of this subsection

(1) How to install JP1/IM - Manager
(2) How to install JP1/IM - View
(3) About the types of installation

(1) How to install JP1/IM - Manager

To install:

Terminate all programs.

Before you start the installation, terminate all programs.

Stop the JP1/Base services.

If you are performing an upgrade installation, stop the JP1/Console service. If a JP1/IM - View is connected to the JP1/IM - Manager for which you want to perform an upgrade installation, the login user should log out from the JP1/IM - Manager.

Insert the distribution medium in the corresponding drive and start the installation.

Follow the instructions of the installer, which starts automatically.

Select the software you want to install, and then enter the following items:

User information

Enter this information only if you are performing a new installation. If you are upgrading from an old version of JP1/IM - Manager, JP1/IM - Central Console, or JP1/IM - Central Scope, the information specified for the old version will be inherited.

Installation folders

In an x64 environment, do not install JP1/IM under system-drive\Program Files\ (the Program Files folder without x86). Problems might occur during operation if JP1/IM is in the Program Files folder that contains 64-bit modules.

The installation folders listed below are created when you install JP1/IM - Manager.

Table 1‒1: Folders created during installation
Product	Folder that is created^#1	Description
JP1/IM - Manager	`installation-folder\JP1IMM\`^#2	Stores JP1/IM - Manager information
	`installation-folder\JP1Cons\`^#2	Stores Central Console information
	`installation-folder\JP1Scope\`^#2	Stores Central Scope information

#1: The default installation folder is system-drive:\Program Files\Hitachi. This value might differ depending on the environment because the value system-drive:\Program Files is determined by the environment variable of the OS at installation in Windows 8.1, Windows 8, Windows Server 2012, Windows 7, Windows Server 2008, or Windows Vista.

#2: If an old version of JP1/IM - Manager, JP1/IM - Central Console, or JP1/IM - Central Scope was installed in a different folder, that installation folder is inherited and the folders listed above are not created.

Note that the drive that is specified as the installation folder for JP1/IM - Manager must be a fixed disk.

If you are prompted to restart the system, restart Windows.

Windows must be restarted when Hitachi Network Objectplaza Trace Library (HNTRLib2) is installed. For details, see 1.3.3 Notes about installing and uninstalling.

When you install JP1/IM - Manager for Windows Server 2003 or Windows XP Professional, the file below is created as an installer log. This file contains maintenance information that is used in the event of abnormal termination of installation. Once JP1/IM - Manager has been installed successfully, start it. If there are no problems, delete the following file:

Windows-installation-folder\Temp\HITACHI_JP1_INST_LOG\jp1imm_inst{1|2|3|4|5}.log

When you install JP1/IM - Manager for Windows Server 2012 or Windows Server 2008, an installer log is not created.

When you install JP1/IM - Manager from the provided distribution medium, Hitachi Program Product Installer logs are output. You do not need to check or delete these files.

Important note

You must specify a fixed disk as the drive for the JP1/IM - Manager installation folder. JP1/IM - Manager and JP1/IM - View must not be installed on a removable disk, network drive, or UNC path.

It will not be possible to upgrade JP1/IM - Manager if JP1/IM - Central Console or JP1/IM - Central Scope is installed anywhere other than on a fixed disk.

To Page Top

(2) How to install JP1/IM - View

To install:

Terminate all programs.

Before you start the installation, terminate all programs.

Insert the distribution medium in the corresponding drive and start the installation.

Follow the instructions of the installer, which starts automatically.

Select the software you want to install, and then enter the following items:

User information

Enter this information only if you are performing a new installation.

Installation folders

In an x64 environment, do not install JP1/IM under system-drive\Program Files\ (the Program Files folder that is not x86 compatible). Problems might occur during operation if JP1/IM is in the Program Files folder that contains 64-bit modules.

The installation folders listed below are created when you install JP1/IM - View.

Table 1‒2: Folders created during installation
Product	Folder that is created^#1	Description
JP1/IM - View	`installation-folder\JP1CoView\`^#2	Stores JP1/IM - View information

#2: If an old version of JP1/IM - View was installed in a different folder, that installation folder is inherited and the default folder listed above is not created.

Note that the drive that is specified as the installation folder for JP1/IM - View must be a fixed disk.

Program folder

Specify the registration location in the Start menu. Note that you cannot specify a program folder when you install JP1/IM - View for Windows 8.1, Windows 8, Windows Server 2012, Windows 7, Windows Server 2008, and Windows Vista.

If you are prompted to restart the system, restart Windows.

Windows must be restarted when Hitachi Network Objectplaza Trace Library (HNTRLib2) is installed. For details, see 1.3.3 Notes about installing and uninstalling.

When you install JP1/IM - View for Windows XP Professional or Windows Server 2003, the following file is created as an installer log. This file contains maintenance information that is used in the event of abnormal termination of installation. Once JP1/IM - View has been installed successfully, start it. If there are no problems, delete the following file:

Windows-installation-folder\Temp\HITACHI_JP1_INST_LOG\jp1coview_inst{1|2|3|4|5}.log

When you install JP1/IM - View for Windows 8.1, Windows 8, Windows Server 2012, Windows 7, Windows Server 2008, or Windows Vista, an installer log is not created.

Important note

You must specify a fixed disk as the drive for the JP1/IM - View installation folder. JP1/IM - View must not be installed on a removable disk, network drive, or UNC path.

It will not be possible to upgrade JP1/IM - View if it is installed anywhere other than on a fixed disk.

To Page Top

(3) About the types of installation

Upgrade installation

If you are upgrading from an old version, first read the notes about upgrading that you will find in 12.2 Upgrading from a previous version of JP1/IM in the Job Management Partner 1/Integrated Management - Manager Overview and System Design Guide.

Remote installation using JP1/Software Distribution

JP1/IM supports remote installation (software distribution) using JP1/Software Distribution.

By running JP1/Software Distribution on the server where JP1/IM is run, you can perform a new installation as well as an upgrade installation of JP1/IM. For details about how to perform remote installation using JP1/Software Distribution, see the Job Management Partner 1/Software Distribution Administrator's Guide Volume 1.

To Page Top