1.7.3 操作時の注意事項
-
次に示す条件が重なると,インポートの処理結果が不正になることがあるため,インポートしないでください。
-
次の項目のどれかの2行目以降に「unit=」または「eun=」の文字列が定義されている。
・UNIXジョブの「コマンド文」
・メール受信監視ジョブの「本文一覧」
・Windowsイベントログ監視ジョブの「説明」
・メール送信ジョブの「本文」
・カスタムUNIXジョブの「コマンド文」
-
ルートジョブグループ直下のユニット以外で,1.の条件を満たすジョブを配下に含むユニットと同階層のユニットをインポートする。
-
-
インポートまたはエクスポート時に指定する文字コード種別には,「AUTO」を指定してください。「AUTO」以外を指定する場合,必ず接続先のJP1/AJS3 - ManagerまたはJP1/AJS2 - Managerの環境設定パラメーター「AJSCHARCODE」に設定されている値を指定してください。異なる文字コード種別を指定すると,KAVZ0904-Eエラーの発生や,設定と異なる文字コードで接続先のJP1/AJS3 - ManagerまたはJP1/AJS2 - Managerのデータベースを更新してしまうなど,処理結果が不正になることがあります。
なお,文字コード種別がUTF-8の場合は,文字コード種別に「AUTO」を指定してください。
-
大量の定義情報が一つのセルに出力された場合,行の区分の色が変わりその行の最後にKAVZ0310-Wのメッセージが出力されることがあります。このメッセージが出力された行の区分に,一括か単独を指定してエクスポートを実行するとエラーが発生したり,定義情報が失われたりするため注意してください。エクスポートする場合は,問題のセルの内容をすべて削除するか,修正してからエクスポートを実行してください。
-
インポートやエクスポートの実行中,またはajsdaconvertコマンドの実行中に[ESC]キーを押さないでください。誤って[ESC]キーを押してしまうと継続または終了した処理の結果が不正になることがあります。
-
インポートまたはエクスポートをした結果,JP1/AJS3 - Definition AssistantとJP1/AJS3 - ViewまたはJP1/AJS2 - Viewのデフォルトの表示方法が異なる場合があります。
-
接続先のマネージャーホストでサポートされていないユニット定義情報をエクスポートするとエラーが発生します。サポートされていないユニット定義情報を削除してからエクスポートしてください。
このため,上位バージョンからインポートしたユニット定義情報を下位バージョンにエクスポートする場合は,接続先のマネージャーホストよりあとのバージョンでサポートされた項目を削除してから,エクスポートしてください。
-
JP1/AJS3 - Definition Assistantは,接続先のマネージャーホストで,文字コード種別と異なる文字コードで定義されたユニット定義情報が混在する場合には正常に動作しません。
-
JP1/AJS3 - Definition Assistantは,インポートまたはエクスポート時に内部的にJP1/AJSのコマンドを実行します。コマンドの操作仕様やエラーの内容などについては,必要に応じてJP1/AJSのマニュアルを参照してください。インポートまたはエクスポート時に使用するコマンドを次に示します。
インポート
-
ajsprint
エクスポート
-
ajsprint
-
一括:ajsdefine
-
単独:ajsdefine,ajschgnet
-
変更:ajschange,ajschgnet,ajschgjob,ajscalendar
-
削除:ajsdelete
-
-
ユニット定義情報にタブ文字を含むユニットをインポートすると,インポート処理結果が不正になる場合があります。ユニット定義情報にタブ文字を含むユニットをインポートしないでください。
ただし,「標準ジョブ定義情報部」の「コマンド文」または「その他の定義情報部」に設定される定義項目の場合は,ユニット定義情報にタブ文字を使用しても不正になりません。「標準ジョブ定義情報部」の「コマンド文」または「その他の定義情報部」にタブ文字を使用している場合のインポート時の表示については,「5.1 定義情報一覧」を参照してください。
-
改行([Alt]+[Enter]キー)で複数の定義を指定できる定義項目を変更対象にする場合,空行を含めてセル内のすべての定義が変更対象になります。
-
「最終更新日時情報部」は,インポートした時点でのユニットの最終更新日時を確認するためのものです。そのため,「最終更新日時情報部」では値を変更できず,エクスポートの対象外となります。
-
一括定義または単独定義は,同一名称のユニットが存在した場合,そのユニットをいったん削除して再作成します。そのため,再作成時にエラーが発生した場合,ユニットが削除された状態になることがあります。