![[Contents]](FIGURE/CONTENT.GIF)
![[Glossary]](FIGURE/GLOSS.GIF)
![[Index]](FIGURE/INDEX.GIF)
![[Back]](FIGURE/FRONT.GIF)
![[Next]](FIGURE/AFTER.GIF)
Job Management Partner 1/Automatic Job Management System 3 Configuration Guide 2
To set up the communication control environment, perform the necessary setup operations in the manager environment (JP1/AJS3 - Manager). Nothing is required in the agent environment (JP1/AJS3 - Agent).
The table below lists the environment setting parameters to be used to set the communication control environment in the manager environment (JP1/AJS3 - Manager).
To determine whether an environment setting parameter is to be set in Windows or UNIX, see the Applicable OS column.
Table 2-6 Environment setting parameters (communication control)
No. Definition key#1 Environment setting parameter Definition Applicable OS Applicable product 1 [{JP1_DEFAULT|logical-host-name}\JP1AJS2\HOST\NETWORK], [{JP1_DEFAULT|logical-host-name}\JP1AJS2\HOST\NETWORK\subkey]#2, and [{JP1_DEFAULT|logical-host-name}\JP1AJSMANAGER\scheduler-service-name\NETWORK\subkey]#2 "ClientConnectTimeout"= Connection timeout Windows
UNIXM 2 "ClientRetryInterval"= Connection retry interval Windows
UNIXM 3 "ClientRetryCount"= Number of connection retries Windows
UNIXM
- Legend:
- M: JP1/AJS3 - Manager
- #1
- Specify JP1_DEFAULT for the physical host. For logical-host-name, specify the name of a logical host.
- #2
- For subkey, specify QUEUEMANAGER for the job execution control manager, QUEUENOTIFY for the job execution control (Notify), and EVMANAGER for the event/action control manager.
The following explains each of the environment setting parameters.
Parameters that are not described here are used for maintenance purposes. Do not change their values.
The default value is used whenever a value is not specified for an environment setting parameter.
- Organization of this section
- (1) "ClientConnectTimeout"=dword:connection-timeout-period
- (2) "ClientRetryInterval"=dword:connection-retry-interval
- (3) "ClientRetryCount"=dword:number-of-connetion-retries
(1) "ClientConnectTimeout"=dword:connection-timeout-period
Use this parameter to specify the connection timeout value to be used when connecting to JP1/AJS3 - Agent.
Note that if the TCP/IP connection timeout value specified in the OS settings is smaller than this value, the setting for the OS takes effect.
- Specifiable values
- A hexadecimal value (in milliseconds) from 00000000 to 05265C00 (0 to 86,400,000 in decimal)
- Default value
- dword:00015F90 (90,000 in decimal)
- Recommended value
- Default value
- When the setting takes effect
- The next time the JP1/AJS3 service is started
If you want to set this parameter on the event/action control manager, see the description in To set the parameter for event/action control below.
n To set the parameter for event/action control
This environment setting parameter has no effect if it is specified for the [{JP1_DEFAULT|logical-host-name}\JP1AJS2\HOST\NETWORK]definition key.
- Specifiable values
- A hexadecimal value (in milliseconds) from 000003E8 to 000927C0 (1,000 to 600,000 in decimal)
- Default value
- In Windows:
dword:00007530 (30,000 in decimal)
- In UNIX:
dword:000003E8 (1,000 in decimal)
- Recommended value
- Set the value appropriate for the operating environment.
- When the setting takes effect
- The next time the JP1/AJS3 service starts
- Cautionary notes
- If this environment setting parameter is omitted, the default value is used.
- For event/action control, even if a value specified for this environment setting parameter is not within the allowable range for the parameter, the JP1/AJS3 services start with the default value as long as the value is allowed by communication control. The allowable ranges of values for communication control are 0 to 999 and 600001 to 86400000 (milliseconds as a decimal).
If the specified value is not allowed by communication control, the KAVS1518-E message is output to the integrated trace log, and the JP1/AJS3 services do not start.
- When setting this environment setting parameter in an agent environment, see 2.4(22) ClientConnectTimeout.
(2) "ClientRetryInterval"=dword:connection-retry-interval
Use this parameter to specify the retry interval for the remote connection timeout (includes connection to JP1/AJS3 - Agent). This environment setting parameter has no effect on event/action control.
- Specifiable values
- A hexadecimal value (in seconds) from 00000000 to 00015180 (0 to 86,400 in decimal)
- Default value
- dword:00000014 (20 in decimal)
- Recommended value
- Default value
- When the setting takes effect
- The next time the JP1/AJS3 service is started
(3) "ClientRetryCount"=dword:number-of-connetion-retries
Use this parameter to specify the number of retries for a remote-communication connection timeout occurring when trying to connect to JP1/AJS3 - Agent. This environment setting parameter has no effect on event/action control.
- Specifiable values
- A hexadecimal value (number of times) from 00000000 to 7FFFFFFF (0 to 2,147,483,647 in decimal)
- Default value
- dword:00000002 (2 in decimal)
- Recommended value
- Default value
- When the setting takes effect
- The next time the JP1/AJS3 service is started
Copyright (C) 2009, 2010, Hitachi, Ltd.
Copyright (C) 2009, 2010, Hitachi Solutions, Ltd.