KFCT73430-E

            aa....aa

                        PRF identifier

                        If the PRF identifier cannot be identified, **** is
                            displayed.

bb....bb

                        Reason code

cc....cc

                        Internal system code

Description
An attempt to start the PRF daemon service has failed.

The PRF daemon service terminates.

Action
Based on the list of reason codes described in the following table, investigate the cause, and
                then remove the cause of the error. However, when exclusive control fails, an
                internal error occurs, and a message other than the listed reason codes appears,
                please contact our customer service.

                                Reason code

                                Cause

                                101

                                Memory is insufficient.

                                102

                                Memory is insufficient.

                                104

                                The new message queue ID in the msgget system
                                    call was not allocated. Check the usage status with the
                                        ipcs command. If an unnecessary message
                                    queue exists, the queue needs to be deleted with the
                                        ipcrm command.

                                106

                                The environment variable PRFSPOOL may not have
                                    been specified or the directory specified in the environment
                                    variable PRFSPOOL may not have been created
                                    correctly.

                                112

                                The specified trace service is already running, or the trace
                                    service is not running but a new trace service cannot be started
                                    because the running process is collecting the trace.

                                115

                                An attempt to access the shared memory used in the PRF daemon
                                    service has failed.

                                117

                                The specified option is invalid.

                                118

                                The shared memory used in the PRF daemon service cannot be
                                    reused. Add the -PrfRemakeBuffer option to the
                                        cprfstart command, and then execute the
                                    command.

                                119

                                An attempt to re-create the shared memory used in the PRF daemon
                                    service has failed. If the process using the PRF daemon service
                                    is running, the shared memory cannot be re-created. If you want
                                    to recreate the shared memory and start the PRF daemon,
                                    terminate the process that is using the PRF daemon service. Note
                                    that, the shared memory is re-created in the following
                                    cases:

                                        When the cprfstart command is executed
                                            with the -PrfRemakeBuffer option
                                            added

                                        When the cprfstart command is executed
                                            with a value different from the previous value (if value
                                            was not specified previously, specify a value other than
                                            8194) specified in the
                                                -PrfTraceBufferSize option

                                502

                                An error occurred while creating the necessary environment to
                                    control the PRF daemon service.

                                1601

                                An error occurred in the system call.

                                3201

                                A timeout occurred when starting the PRF daemon. The PRF daemon
                                    may be running normally.

                                3203

                                An attempted exclusive control has failed.

                                8001

                                An internal error occurred.

Reason code	Cause
101	Memory is insufficient.
102	Memory is insufficient.
104	The new message queue ID in the `msgget` system call was not allocated. Check the usage status with the `ipcs` command. If an unnecessary message queue exists, the queue needs to be deleted with the `ipcrm` command.
106	The environment variable `PRFSPOOL` may not have been specified or the directory specified in the environment variable `PRFSPOOL` may not have been created correctly.
112	The specified trace service is already running, or the trace service is not running but a new trace service cannot be started because the running process is collecting the trace.
115	An attempt to access the shared memory used in the PRF daemon service has failed.
117	The specified option is invalid.
118	The shared memory used in the PRF daemon service cannot be reused. Add the `-PrfRemakeBuffer` option to the `cprfstart` command, and then execute the command.
119	An attempt to re-create the shared memory used in the PRF daemon service has failed. If the process using the PRF daemon service is running, the shared memory cannot be re-created. If you want to recreate the shared memory and start the PRF daemon, terminate the process that is using the PRF daemon service. Note that, the shared memory is re-created in the following cases: When the `cprfstart` command is executed with the `-PrfRemakeBuffer` option added When the `cprfstart` command is executed with a value different from the previous value (if value was not specified previously, specify a value other than 8194) specified in the `-PrfTraceBufferSize` option
502	An error occurred while creating the necessary environment to control the PRF daemon service.
1601	An error occurred in the system call.
3201	A timeout occurred when starting the PRF daemon. The PRF daemon may be running normally.
3203	An attempted exclusive control has failed.
8001	An internal error occurred.