21.5.1 Procedure to enable the job distribution delay reduction function
This subsection describes the procedure to enable the job distribution delay reduction function.
-
Stop the JP1/AJS3 service.
-
Enable the job distribution delay reduction function.
Specify yes for the AGMMONITORING environment setting parameter by executing the following command:
jajs_config -k "[{JP1_DEFAULT|logical-host-name}\JP1AJS2\HOST\AGENTMONITOR]" "AGMMONITORING" = "yes"
-
Specify settings to start the ajsagtmond process.
To start the ajsagtmond process, you must revise the JP1/AJS3 startup process definition file (jp1ajs_hstd.conf). The following shows the storage folders for the JP1/AJS3 startup process definition file (jp1ajs_hstd.conf) and model files:
- For a physical host (in Windows)
-
JP1/AJS3-Manager-installation-folder\conf
- For a physical host (in UNIX)
-
/etc/opt/jp1ajs2/conf
- For a logical host (in Windows)
-
shared-folder\conf
- For a logical host (in UNIX)
-
shared-directory/conf
The procedure to edit the JP1/AJS3 startup process definition file differs depending on whether the file has been updated since JP1/AJS3 was installed. For details about how to edit, see (1) Procedure to edit the JP1/AJS3 startup process definition file.
-
If necessary, change the restart setting of the ajsagtmond process.
The restart of the ajsagtmond process is defined in the extended startup process definition file (jp1ajs_hstd_0700.conf). For details about the extended startup process definition file, see 6.3.1 Restarting an abnormally terminated JP1/AJS3 process in the JP1/Automatic Job Management System 3 Administration Guide.
-
Start the JP1/AJS3 service.
-
Execute the jajs_spmd_status command to confirm that the following process name is displayed:
- In Windows
-
agentmon
- In UNIX
-
ajsagtmond
-
Execute the ajsagtcheck command with the -m status option specified to confirm that the command can be executed normally.
- Organization of this subsection
(1) Procedure to edit the JP1/AJS3 startup process definition file
This subsection describes the procedure to edit the JP1/AJS3 startup process definition file.
The procedure differs depending on whether the file has been updated since JP1/AJS3 was installed.
(a) Procedure to apply if the JP1/AJS3 startup process definition file has not been updated
If the JP1/AJS3 startup process definition file has not been updated, edit the file by completing the following procedure:
-
Back up the JP1/AJS3 startup process definition file (jp1ajs_hstd.conf), and store the backup file in any folder.
-
Copy the model file (jp1ajs_hstd_agtmon.conf.model).
-
Rename the copy of the model file to jp1ajs_hstd.conf, and then overwrite the file.
(b) Procedure to apply if the JP1/AJS3 startup process definition file has been updated
If the JP1/AJS3 startup process definition file has been updated, edit the file by completing the following procedure:
-
Open the model file for the JP1/AJS3 startup process definition file (jp1ajs_hstd_agtmon.conf.model) by using a text editor.
-
Copy the definition entry for the ajsagtmond process in the model file, and then close the file.
The entry to be copied is as follows:
- In Windows
-
agentmon|ajsagtmond.exe|||1800|
- In UNIX
-
ajsagtmond|/opt/jp1ajs2/bin/ajsagtmond|||1800|
-
Open the JP1/AJS3 startup process definition file (jp1ajs_hstd.conf) by using a text editor.
-
Add the definition entry for the ajsagtmond process.
Create a new line anywhere in the file, and paste the entry that you copied in step 2.
-
Save and close the JP1/AJS3 startup process definition file.