2.18 Messages from KECT01001 to KECT12999
This section describes the messages from KECT01001 to KECT12999.
-
KECT01001-I
The file aa....aa already exists. Do you want to overwrite it?
aa....aa: File name
- Description
-
An attempt was made to save a file with the same name as an existing file.
- (S)
-
The Yes and No buttons will be displayed.
- (O)
-
To overwrite the file, click the Yes button and to cancel the processing, click the No button.
-
KECT01002-I
The settings will be specified after deleting the mapping lines to the transformation destination node that you do not want to map. Do you want to continue?
- Description
-
The nodes other than the selected transformation destination node or the descendants of the selected transformation destination node have been mapped.
- (S)
-
The [Yes] and [No] buttons are displayed.
- (O)
-
If you click the [Yes] button, the settings are specified after deleting the mapping lines connected to the nodes other than the selected transformation destination node, and its descendant nodes. If you click the [No] button, the control returns to the mapping definition editor without performing any operation.
-
KECT02100-I
The data transformation definition file was generated successfully.
- Description
-
the data transformation definition file is generated.
- (S)
-
Outputs the data transformation definition file.
-
KECT02101-E
An error occurred during validation of the mapping definition file. (cause = aa....aa)
aa....aa: Information about the exception that caused the error
- Description
-
A validation error occurred during the validation of the mapping definition file.
- (S)
-
After the validation of the mapping definition file is completed, the system stops building a data transformation definition file.
- (O)
-
Refer to the information about the exception that caused the error, and take the necessary corrective action.
-
KECT02102-E
An fatal error occurred during validation of the mapping definition file. (cause = aa....aa)
aa....aa: Information about the exception that caused the error
- Description
-
A validation error due to which operations cannot be continued occurred during the validation of the mapping definition file.
- (S)
-
Stops validation of the mapping definition file and stops building a data transformation definition file.
- (O)
-
Refer to the information about the exception that caused the error, and take the necessary corrective action.
-
KECT02103-E
An attempt to load the mapping definition file has failed. (cause = aa....aa)
aa....aa: Information about the exception that caused the error
- Description
-
An error occurred while the mapping definition file was being loaded.
- (S)
-
Stops building a data transformation definition file.
- (O)
-
Refer to the information about the exception that caused the error, and take the necessary corrective action.
-
KECT02104-E
An attempt to generate the data transformation definition file has failed. (cause = aa....aa)
aa....aa: Information about the exception that caused the error
- Description
-
An error occurred while the data transformation definition file was being generated.
- (S)
-
Stops building a data transformation definition file.
- (O)
-
Refer to the information about the exception that caused the error, and take the necessary corrective action.
-
KECT02105-E
An unexpected error occurred. (cause = aa....aa)
aa....aa: Information about the exception that caused the error
- Description
-
An unexpected error occurred.
- (S)
-
Stops building a data transformation definition file.
- (O)
-
Contact a customer engineer.
-
KECT02106-E
The repository is invalid. (details = aa....aa)
aa....aa: Detailed error information
- Description
-
An invalid repository was specified.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Refer to the detailed error information, and take the necessary corrective action.
-
KECT02107-E
A consistency check of the XML Schema used in the mapping definition file has failed. Cause = aa....aa
aa....aa: Information about the exception that caused the error
- Description
-
An error occurred during the consistency check of XML Schema used in the mapping definition file.
- (S)
-
Building of the data transformation definition file will be canceled.
- (O)
-
Reference the exception information that caused the error, and then take the required actions.
-
KECT02108-E
The XML Schema used by the mapping definition file has been changed.
- Description
-
The contents of the XML Schema used in the mapping definition file differ from the contents of the XML Schema set up in the variable.
- (S)
-
Building of the data transformation definition file will be canceled.
- (O)
-
Check the XML Schema used in the mapping definition file, and then re-define the mapping definition.
-
KECT04001-E
Specify a file whose extension is "mdo".
- Description
-
A file whose extension is not mdo was registered.
- (S)
-
Displays an error message and cancels the processing.
- (O)
-
Check the file extension.
-
KECT04002-E
The selected node cannot be added. The selected node, or an ancestor or descendent of that node, has already been added.
- Description
-
The selected node, or an ancestor or descendent node of the selected node, has already been added.
- (S)
-
Displays an error message and cancels the processing.
- (O)
-
Check the selected node.
-
KECT04003-E
The transformation function definition file is not registered.
- Description
-
The transformation function definition file is not registered.
- (S)
-
Displays an error message and cancels the processing.
- (O)
-
Register the transformation function definition file.
-
KECT04004-E
An error occurred while reading the transformation function definition file. cause = aa....aa
aa....aa: Information about the exception that caused the error
- Description
-
The transformation function definition file cannot be read.
- (S)
-
Displays an error message and cancels the processing.
- (O)
-
Confirm that the transformation function definition file exists. If the file exists, confirm that the user has the access permission.
-
KECT04005-E
An error occurred while parsing the transformation function definition file. For details about an error, reference the console. Path = aa....aa
aa....aa: File name
- Description
-
An error occurred during the parsing of the transformation function definition file.
- (S)
-
Displays an error message and cancels the processing.
- (O)
-
Check, and if necessary, revise the contents defined in the specified transformation function definition file.
-
KECT04006-E
The format for describing file is incorrect. Cause = aa....aa
aa....aa: Detailed error information
- Description
-
The transformation function definition file is not in the XML format or an error occurred during the XML Schema validation.
- (S)
-
Displays an error message and continues the processing.
- (O)
-
Reference the detailed error information, and correct the transformation function definition file according to the details.
-
KECT04007-E
The coded contents are incorrect. Cause = aa....aa:bb....bb
aa....aa: Detailed error information
bb....bb: Location of error
- Description
-
A string that cannot be used for the name is specified in the definition of the transformation function definition file.
- (S)
-
Displays an error message and continues the processing.
- (O)
-
Reference the error details, and correct the transformation function definition file according to the details.
-
KECT04009-E
An error occurred while parsing the transformation function definition file. For details about an error, reference the console.
- Description
-
An error occurred during the parsing of the transformation function definition file.
- (S)
-
Displays an error message and cancels the processing.
- (O)
-
Check and, if necessary, revise the contents defined in the specified transformation function definition file.
-
KECT04010-I
The file already exists. Do you want to overwrite it? Path = aa....aa
aa....aa: File name
- Description
-
A file with the same name exists in the output destination of the Java form file.
- (S)
-
The Yes, Yes to All, No, and Cancel buttons will be displayed.
- (O)
-
To overwrite the file, click the Yes or Yes to All buttons. If you do not want to overwrite the file, click the No button. To cancel the processing, click the Cancel button.
-
KECT04011-E
An attempt to write to the file has failed. Cause = aa....aa
aa....aa: Information about the exception that caused the error
- Description
-
An attempt to write to a file failed.
- (S)
-
Displays an error message and cancels the processing.
- (O)
-
Check whether the output destination of the Java form file exists. If the output destination exists, confirm that the user has the access permission.
-
KECT04012-I
The transformation function has been changed. Do you want to update it? If you update the function, the value entered in the argument will be unset up.
- Description
-
A transformation function where One of the following values is changed, is selected during the transformation function re-selection process:
-
jar file name
-
Package name
-
Class name
-
Method name
-
Number of arguments
-
Argument name
-
- (S)
-
The OK or Cancel buttons will be displayed.
- (O)
-
To unset up the entered values, click the OK button. Click the Cancel button to cancel the processing, and then return to the Select Transformation Function dialog box.
-
KECT04013-I
A comment has been changed. Do you want to update the comment?
- Description
-
The method or argument comments are changed in the transformation function selected during the transformation function re-selection process.
- (S)
-
The OK or Cancel buttons will be displayed.
- (O)
-
To change the comments, click the OK button. Click the Cancel button to cancel the processing, and then return to the Select Transformation Function dialog box.
-
KECT04014-E
Please select a transformation function.
- Description
-
The OK button was clicked without selecting the transformation function.
- (S)
-
Displays an error message and cancels the processing.
- (O)
-
Select the transformation function, and then click the OK button or click the Cancel button to cancel the processing.
-
KECT04017-W
A warning was issued during the parsing of the transformation function definition file. Cause = aa....aa
aa....aa: Information about the exception that caused the warning
- Description
-
An error occurred during an XML parsing.
- (S)
-
The message log will be output.
- (O)
-
Reference the warning details and check whether there is a problem.
-
KECT04018-E
The selected node cannot be set up. The selected node, or an ancestor or descendent of that node, has already been set up in the default path or linked path.
- Description
-
The selected node, or an ancestor or descendent node of the selected node, is already set up in the default or linked path.
- (S)
-
An error message is displayed and processing is cancelled.
- (O)
-
Check the selected node.
-
KECT04019-E
The same radix has been set up for the input radix and output radix.
- Description
-
The same radix is set up for the input radix and output radix values.
- (S)
-
If you click the [OK] button for the error message, the control returns to the window for setting up the [Radix conversion] dialog box.
- (O)
-
Specify a different radix for the input radix and output radix.
-
KECT05001-E
An internal error occurred. (details = aa....aa)
aa....aa: Detailed error information
- Description
-
An internal error occurred.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Contact a customer engineer.
-
KECT05002-E
An attempt to load the file has failed. (cause = aa....aa)
aa....aa: Information about the exception that caused the error
- Description
-
The file cannot be read.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Contact a customer engineer.
-
KECT05003-E
An attempt to load the file has failed. (path = aa....aa)
aa....aa: File path
- Description
-
The file cannot be read.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Contact a customer engineer.
-
KECT05004-E
An attempt to write to the file has failed.
- Description
-
An attempt to write to a file failed.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Contact a customer engineer.
-
KECT05005-E
An unexpected error occurred. (cause = aa....aa)
aa....aa: Information about the exception that caused the error
- Description
-
An unexpected error occurred.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Contact a customer engineer.
-
KECT05011-E
The root element has not been selected.
- Description
-
The root element has not been selected in the specified mapping definition file.
- (S)
-
Displays an error message and cancels the processing.
- (O)
-
Check whether the root element has been selected for the mapping definition file.
-
KECT05012-E
A mapping definition cannot be created without a root element selected. Please select a root element.
- Description
-
An attempt was made to create a mapping definition without selecting a root element.
- (S)
-
The OK button will be displayed.
- (O)
-
Click the OK button to display the Select Root Element dialog box again. Select the root element, and then create the mapping definition.
-
KECT10001-E
An error occurred during validation of the Schema. (logical name = aa....aa, detailed information = bb....bb)
aa....aa: XML Schema logical name
bb....bb: Validation error details
- Description
-
An error occurred during the validation of the XML Schema.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Check the specified XML schema.
-
KECT10002-E
An invalid URI or qualification name is being used for targetNamespace. (logical name = aa....aa)
aa....aa: XML Schema logical name
- Description
-
The prefix of targetNamespace in the transformation destination XML Schema begins with x, or an xsl or xsi URI has been specified for targetNamespace.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Check the specified XML schema.
-
KECT10003-E
redefine cannot be used. (logical name = aa....aa)
aa....aa: XML Schema logical name
- Description
-
An item, redefine, which is not supported in the XML Schema, has been defined.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Check the specified XML schema.
-
KECT10004-E
An error occurred during analysis of the XML Schema. (logical name = aa....aa, detailed information = bb....bb)
aa....aa: XML Schema logical name
bb....bb: Error details
- Description
-
An error occurred during the parsing of the XML Schema.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Check the specified XML schema.
-
KECT10005-E
An internal error occurred during analysis of the XML Schema. (logical name = aa....aa, detailed information = bb....bb)
aa....aa: XML Schema logical name
bb....bb: Detailed information
- Description
-
An internal error occurred.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Contact a customer engineer.
-
KECT10006-E
No valid candidate was found for the root element. (logical name = aa....aa)
aa....aa: XML Schema logical name
- Description
-
The global definition element was not found in the XML Schema.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Check the specified XML schema.
-
KECT10008-E
An unverified binary format definition was specified. (logical name = aa....aa)
aa....aa: XML Schema logical name
- Description
-
An unvalidated binary format definition is specified.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Validate the binary format definition, and then re-execute the operation.
-
KECT10009-E
The binary format definition is invalid. (logical name = aa....aa, detailed information = bb....bb)
aa....aa: XML Schema logical name
bb....bb: Detailed information
- Description
-
An invalid binary format definition is specified.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
The binary format definition might be damaged. If the same error occurs even after a validated binary format definition is specified, contact a customer engineer.
-
KECT11000-E
An attempt to create an instance for the command class has failed. (details = aa....aa)
aa....aa: Cause of error
- Description
-
An attempt to generate the command class (internal class) failed.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Contact a customer engineer.
-
KECT11001-E
No command class corresponding to the command search class was found. (command search class = aa....aa)
aa....aa: Command search class name
- Description
-
An attempt to search the command failed.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Contact a customer engineer.
-
KECT11002-E
No data transformation definition can be generated for the target schema that contains an "any" element or "anyattribute" attribute that has one or more minimum occurrence count. (details = aa....aa)
aa....aa: Node path of the any element or the anyattribute attribute
- Description
-
A schema that contains the any element or the anyattribute attribute with a minimum occurrence count of one or more times is specified for the transformation destination schema.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
You cannot execute data transformation by specifying the specified schema as the target schema. Specify a different schema file.
-
KECT11003-E
For the attribute node that has "required" specified for the "use" attribute, no assignment line has been defined. (detailed information = aa....aa)
aa....aa: Attribute node path
- Description
-
The mapping has not been defined for a required attribute.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Define mapping for the required attribute.
-
KECT11004-E
An assignment line has been defined for a complex type element node. (details = aa....aa)
aa....aa: Element node path
- Description
-
The assign mapping is defined for a complex-type element.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Delete the assignment mapping that is defined for the complex-type element.
-
KECT11005-E
A selection function has been connected to another selection function. (details = aa....aa)
aa....aa: Name of the choose node function
- Description
-
A choose node function is connected to another choose node function.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Selection functions cannot be nested. Delete the selection function that is connected to another selection function.
-
KECT11006-E
No mapping has been defined for elements whose minimum occurrence count is two or more. (details = aa....aa)
aa....aa: Element node path
- Description
-
The global definition element was not found in the XML Schema.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Define mapping for the element for which the loop function caused an error.
-
KECT11007-E
No mapping has been defined for simple content elements whose minimum occurrence count is one or more. (details = aa....aa)
aa....aa: Element node path
- Description
-
The mapping has not been defined for a simple content element with a minimum occurrence count of one or more times.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Define mapping for the simple content element for which the error occurred.
-
KECT11008-E
An attempt to add the XSLT node has failed. (additional node = aa....aa, additional destination node = bb....bb)
aa....aa: Name of the added XSLT element
bb....bb: Name of the XSLT element at the addition destination
- Description
-
An invalid node was processed while generating an XSLT.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Contact a customer engineer.
-
KECT11009-E
An error occurred during construction of the XSL tree. (details = aa....aa)
aa....aa: Detailed error information
- Description
-
An error occurred during the construction of the XSL tree.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Refer to the detailed error information, and take the necessary corrective action.
-
KECT11010-E
An internal error occurred. (details = aa....aa)
aa....aa: Detailed error information
- Description
-
An internal error occurred during the generation processing.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Contact a customer engineer.
-
KECT12000-E
An attempt to generate an instance for the command class has failed. (details = aa....aa)
aa....aa: Cause of error
- Description
-
An attempt to generate the command class (internal class) failed.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Contact a customer engineer.
-
KECT12001-E
No command class corresponding to the command search class was found. (command search class = aa....aa)
aa....aa: Command search class name
- Description
-
An attempt to search the command failed.
- (S)
-
Displays an error message and stops the processing.
- (O)
-
Contact a customer engineer.
-
KECT12002-E
aa....aa mapping lines cannot be connected to the input. (name = bb....bb, maximum number of connectable lines = cc....cc)
aa....aa: Number of connected mapping lines
bb....bb: Node name
cc....cc: Number of connectable mapping lines
- Description
-
The number of mapping lines connected to the input do not match the number of connectable lines.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Check the mapping lines connected to the applicable node.
-
KECT12003-E
aa....aa mapping lines cannot be connected to the output. (name = bb....bb, maximum number of connectable lines = cc....cc)
aa....aa: Number of connected mapping lines
bb....bb: Node name
cc....cc: Number of connectable mapping lines
- Description
-
The number of mapping lines connected to the output do not match the number of connectable lines.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Check the mapping lines connected to the applicable node.
-
KECT12004-E
aa....aa cannot be specified for the input node. (name = bb....bb)
aa....aa: Name of the connected node
bb....bb: Node name
- Description
-
A node that cannot be connected to the input has been connected.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Check the mapping lines connected to the applicable node.
-
KECT12005-E
aa....aa cannot be specified for the output node. (name = bb....bb)
aa....aa: Name of the connected node
bb....bb: Node name
- Description
-
A node that cannot be connected to the output has been connected.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Check the mapping lines connected to the applicable node.
-
KECT12006-E
No mapping has been defined for a required attribute node. (name = aa....aa, dependent target = bb....bb)
aa....aa: Node name
bb....bb: Name of loop node function at dependent destination
- Description
-
The mapping lines are not defined for a required attribute node.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Check the mapping lines connected to the applicable node.
-
KECT12007-E
No selection condition has been defined. (name = aa....aa)
aa....aa: Node name
- Description
-
The mapping lines are defined for the choose node function, but the corresponding conditions have not been set up.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Check the mapping lines connected to the applicable node.
-
KECT12008-E
You cannot define "no node output" for a required node. name = aa....aa
aa....aa: Function name
- Description
-
for a function mapped to a required node, the no node output is selected and the ancestor node does not contain an omissible node.
- (S)
-
An error message is displayed and the validation processing continues.
- (O)
-
Review and, if necessary, revise the information output for the applicable function.
-
KECT12009-E
No mapping has been defined for a required element node. (name = aa....aa, dependent target = bb....bb)
aa....aa: Node name
bb....bb: Name of loop node function at dependent destination
- Description
-
The mapping lines have not been defined for a required element node.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Check the mapping lines connected to the applicable node.
-
KECT12010-E
Multiple assignment lines cannot be defined if they have the same dependent target. (name = aa....aa, dependent target = bb....bb)
aa....aa: Node name
bb....bb: Name of loop node function at dependent destination
- Description
-
Multiple assign lines with the same dependence target have been defined for the same transformation destination schema node.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
The maximum number of assignment lines that can be defined for the same transformation-target schema node is 1 per dependent target.
Delete the multiple assignment lines that are defined.
-
KECT12011-E
A repeating correspondence line and an assignment line that have the same dependent target cannot be defined simultaneously. (name = aa....aa, dependent target = bb....bb)
aa....aa: Node name
bb....bb: Name of loop node function at dependent destination
- Description
-
The loop mapping lines and assign lines with the same dependence target have been defined at the same time for the same transformation destination schema node.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
A looping mapping line and an assignment line that have the same dependent target cannot be defined simultaneously for the same transformation-target schema node.
Delete either the looping mapping line or the assignment line.
-
KECT12012-E
Repeating functions cannot be nested for the same transformation target schema node. (name = aa....aa)
aa....aa: Node name
- Description
-
A nested loop definition has been defined for the same transformation destination schema node.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Looping definitions cannot be defined in a nested format for the same transformation-target schema node.
Delete the nested looping mapping lines.
-
KECT12013-E
An internal error occurred. (details = aa....aa)
aa....aa: Detailed error information
- Description
-
An internal error occurred during validation.
- (S)
-
Displays an error message and stops the validation process.
- (O)
-
Contact a customer engineer.
-
KECT12014-E
The occurrence count of the mapping definition at the transformation source does not match the equivalent count at the transformation target. (name = aa....aa, dependent target = bb....bb)
aa....aa: Node name
bb....bb: Name of loop node function at dependent destination
- Description
-
The occurrence count of the mapping definition at the transformation source does not match the count at the transformation destination.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Check the mapping lines connected to the applicable node.
-
KECT12015-E
A node that cannot be mapped has been defined as a required node. (name = aa....aa)
aa....aa: Node name
- Description
-
A node that cannot be mapped to the transformation destination schema has been defined as a required node.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
If any of the ancestor nodes of the applicable node has a minimum occurrence count of 0, define mapping such that that node and its descendants are not output.
-
KECT12016-E
There is no mapping line for the entered data. (name = aa....aa)
aa....aa: Node name
- Description
-
The input mapping lines are not connected.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Define a mapping line for input for the applicable node.
-
KECT12017-E
No value can be output for the complex content element. (name = aa....aa)
aa....aa: Node name
- Description
-
Assign mapping is not defined for a complex-type element.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Check the mapping lines connected to the applicable node.
-
KECT12018-E
No empty node can be output for an element that has a required element in the child node. (name = aa....aa)
aa....aa: Node name
- Description
-
The output of an empty element is defined for an element that has an element with a non-zero minimum occurrence count as a child element.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Check the mapping lines connected to the applicable node.
-
KECT12019-E
Mapping has not been defined for any of the descendant nodes of the "choice" structure element. (name = aa....aa, dependent target = bb....bb)
aa....aa: Node name
bb....bb: Name of loop node function at dependent destination
- Description
-
Although all the child elements of the choice structural element are required elements, the mapping is not defined for the descendant of any child element.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Check the mapping lines connected to the applicable node.
-
KECT12020-E
No empty node can be output for the "choice" structure element if all children nodes are required elements. (name = aa....aa)
aa....aa: Node name
- Description
-
Although all the child elements of the choice structural element are required elements, the output of an empty element is defined
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Check the mapping lines connected to the applicable node.
-
KECT12021-E
There is a mapping line that does not have a dependent target. (name = aa....aa, connection source = bb....bb)
aa....aa: Node name
bb....bb: Name of the connection source node
- Description
-
A mapping line that does not have a dependence target was found while the mapping related to the dependence target was being validated.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
There might be a mapping line that is not connected to the source node. Verify that all mapping lines are correctly connected to the source node.
-
KECT12022-E
No value has been set for mapping the node that is not a complex content element. (name = aa....aa)
aa....aa: Node name
- Description
-
A condition was found wherein the value to be output to the choose node function connected to a transformation destination node, which is not a complex content element, has not been specified.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Check the mapping lines connected to the applicable node.
-
KECT12023-E
The data transformation definition cannot be generated because there are too many mapping lines.
- Description
-
The size of the data transformation definition file has exceeded the limit.
- (S)
-
Displays a message and ends the validation process.
- (O)
-
Reduce the number of mapping lines that are defined.
If the error persists even after you have reduced the number of mapping lines, contact a customer engineer.
-
KECT12024-E
No root element was found. (name = aa....aa)
aa....aa: Logical name of the transformation destination schema
- Description
-
The root element of the transformation destination schema was not found.
- (S)
-
Displays a message and ends the validation process.
- (O)
-
Verify that a root element has been selected.
-
KECT12025-E
When the NodeList type custom function is defined for an element, mapping cannot be performed to a descendant node that has the same dependence target. name=aa....aa, dependence target=bb....bb
aa....aa: Node name
bb....bb: Name of the loop node function at the dependence destination
- Description
-
The NodeList type custom function is defined for an element, and the mapping is defined for a descendant node with the same dependence target.
- (S)
-
An error message is displayed and the validation processing continues.
- (O)
-
Delete the mapping lines for the descendant node, or delete the mapping lines for the custom function where the return value is the NodeList type.
-
KECT12026-E
The attributes cannot be mapped because the NodeList type custom function is specified in the output value of the choose node function. name=aa....aa
aa....aa: Function name
- Description
-
The NodeList type custom function is specified in the output value for a condition of the choose node function and mapped to an attribute.
- (S)
-
An error message is displayed and the validation processing continues.
- (O)
-
Review and, if necessary, revise the mapping lines connected to the applicable node.
-
KECT12027-E
A node or function that cannot be specified as an argument of the aa....aa type custom function has been defined. name=bb....bb
aa....aa: Return value type
bb....bb: Function name
- Description
-
A node or a function that cannot be mapped is specified for an argument.
- (S)
-
An error message is displayed and the validation processing continues.
- (O)
-
Change the return value type, or review and, if necessary, revise the node or function specified in the argument.
-
KECT12028-E
A node or function that cannot be specified in the output destination of the aa....aa type custom function has been defined. name=bb....bb
aa....aa: Return value type
bb....bb: Function name
- Description
-
A node or a function that cannot be mapped is specified in the output destination.
- (S)
-
An error message is displayed and the validation processing continues.
- (O)
-
Change the return value type, or review and, if necessary, revise the node or function specified in the output destination.
-
KECT12029-E
When the NodeList type custom function is output, the other output values must also be set to the NodeList type custom function. name=aa....aa
aa....aa: Function name
- Description
-
When the NodeList type custom function is specified for other output values, the node output and value output is specified and a function other than the NodeList type custom function is specified for the transformation destination node, which is a complex content element.
- (S)
-
An error message is displayed and the validation processing continues.
- (O)
-
Change the output value to the NodeList type custom function, or review and, if necessary, revise the transformation destination node.
-
KECT12030-E
A transformation source variable node that is defined second or later cannot be specified for an argument of the NodeList type custom function. name=aa....aa
aa....aa: Function name
- Description
-
A transformation source variable node that is defined second or later is specified for an argument of the NodeList type custom function.
- (S)
-
An error message is displayed and the validation processing continues.
- (O)
-
Review and, if necessary, revise the node or return value type specified in the argument.
-
KECT12031-E
The defined function cannot be specified as an input of the aa....aa function. name= bb....bb
aa....aa: Type of function
-
Convert number format
-
Perform node operation
-
Round node
-
NOT operation
-
Logical operation
-
Shift operation
-
Radix conversion
bb....bb: Function name
- Description
-
An unmappable function has been specified in [Input].
- (S)
-
An error message is displayed and the validation processing continues.
- (O)
-
Review and, if necessary, revise, the function specified in [Input].
-
-
KECT12100-I
The mapping definition was verified successfully.
- Description
-
The validation processing was successful.
- (S)
-
Displays a message and ends the validation process.
-
KECT12101-I
Error: aa....aa, Warning: bb....bb, Information: cc....cc
aa....aa: Error count
bb....bb: Warning count
cc....cc: Information count
- Description
-
This message describes the number of messages issued during validation.
- (S)
-
Displays a message and ends the validation process.
-
KECT12500-W
The occurrence count of the mapping definition at the transformation source might not match the occurrence count of the mapping definition at the transformation target. (name = aa....aa, dependent target = bb....bb)
aa....aa: Node name
bb....bb: Name of loop node function at dependent destination
- Description
-
The occurrence count of the mapping definition at the transformation source might not match the count at the transformation destination.
- (S)
-
Displays a warning message and continues the validation process.
- (O)
-
If the occurrence count at the mapping source does not match the occurrence count at the mapping target, a validation error might occur during transformation execution.
Check the occurrence count of the applicable node inside the XML data to be transformed to make sure that a validation error does not occur during execution.
-
KECT12501-W
Mapping has been defined simultaneously for multiple child nodes of the "choice" structure element. An error might occur during execution. (name = aa....aa, dependent target = bb....bb)
aa....aa: Node name
bb....bb: Name of loop node function at dependent destination
- Description
-
The mapping has been defined for multiple child elements or descendant nodes of the choice structural element.
- (S)
-
Displays a warning message and continues the validation process.
- (O)
-
Multiple child elements of the choice structure element might occur simultaneously, causing a validation error during transformation execution.
Check the mapping under the applicable choice structure to make sure that multiple child elements do not occur simultaneously.
-
KECT12502-W
The selection function has been defined for a child node of the "choice" structure element. (name = aa....aa, dependent target = bb....bb)
aa....aa: Node name
bb....bb: Name of the loop node function at dependent destination
- Description
-
Although all the child elements of the choice structural element are required elements, the choose node function has been defined.
- (S)
-
Displays a warning message and continues the validation process.
- (O)
-
If Do not output the node is defined for the choose node function, a validation error might occur during transformation execution.
Make sure that Do not output the node is not defined for the choose node function.
-
KECT12503-E
No conversion table ID is specified.
- Description
-
The transformation table ID is not specified.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Specify the conversion table ID.
-
KECT12504-W
Any element in the mapping definition at the transformation source might not match the any element in the transformation destination. Name = aa....aa
aa....aa: Node name
- Description
-
There are multiple any elements in the child element of the complex content element.
- (S)
-
Displays a warning message and continues the validation process.
- (O)
-
The any element in the mapping definition at the transformation source might not match the any element in the transformation destination. As a result, a validation error might occur during the execution of transformation.
Check the any element of the corresponding node in the XML data to be transformed, and make sure that a validation error does not occur at runtime.
-
KECT12508-E
A transformation function is not selected. Name = aa....aa
aa....aa: Function name
- Description
-
A transformation function has not been selected in the definition of the custom function.
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Select a transformation function in the custom function.
-
KECT12509-E
The number of input mapping lines must match the argument. Name = aa....aa
aa....aa: Function name
- Description
-
The entered mapping lines do not match the number of arguments in the custom function (custom).
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Check the custom function (custom) settings.
-
KECT12510-E
Input values have not been set up for all the arguments. Name = aa....aa
aa....aa: Function name
- Description
-
The input values are not specified for all the arguments in the custom function (custom).
- (S)
-
Displays an error message and continues the validation process.
- (O)
-
Check the custom function (custom) settings.
-
KECT12511-W
There are mapping lines from the transformation source where the nillable attribute is specified to the transformation destination where the nillable attribute is not specified. The nil attribute is not applied at the transformation destination. Name = aa....aa, dependent target = bb....bb
aa....aa: Node name
bb....bb: Name of loop node function at dependent destination
- Description
-
The mapping has been defined from an element with the nillable attribute specified in the transformation source schema to an element with the nillable attribute not specified in the transformation destination schema.
- (S)
-
Displays a warning message and continues the validation process.
- (O)
-
Check whether the nillable attribute is required in the transformation destination node.
-
KECT12514-W
"No node output" has been defined for a required node. name=aa....aa
aa....aa: Function name
- Description
-
The No node output is selected in a function mapped to a required node of a descendant of an omissible parent element.
- (S)
-
A warning message is displayed, and the validation processing continues.
- (O)
-
Review and, if necessary, revise the information output for the applicable function.
-
KECT12516-E
The XPath expression is invalid. (name = aa....aa, details = bb....bb)
aa....aa: Function name
bb....bb: Detailed error information
- Description
-
The XPath expression specified in the XPath function is invalid.
- (S)
-
Displays the message and continues the validation process.
- (O)
-
Check the detailed error information and make sure that the specified XPath expression is correct.
-
KECT12517-E
An error occurred during validation of the data transformation definition. (detail = aa....aa)
aa....aa: Detailed error information
- Description
-
The generated data transformation definition is invalid.
- (S)
-
Displays the message and continues the validation process.
- (O)
-
Check the detailed error information and make sure that the XPath expression specified in the XPath function is correct. If that XPath expression is correct or if no XPath function is used, contact the maintenance personnel.