A.1 Tables in the extended MIB object definition file
This section describes the tables of the extended MIB object definition file.
The OIDs of each table are as follows:
.iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).hitachi(116).systemExMib(5).cosminexusMibs(33).manager(1)
- Organization of this subsection
-
(1) j2eeContainerTable
The following table describes j2eeContainerTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
j2eeContainerTable (1) |
j2eeContainerEntry (1) |
j2eeContainerIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
None |
|
j2eeContainerFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name" |
|||
|
j2eeContainerServerName (3) |
DisplayString |
RO |
-- |
Name of the J2EE server |
|||
|
j2eeContainerNamingServiceHost (4) |
DisplayString |
RO |
-- |
Host name of the Naming Service to which the J2EE server is to be connected. |
|||
|
j2eeContainerNamingServicePort (5) |
INTEGER |
RO |
-- |
Port number of the Naming Service to which the J2EE server is to be connected. |
|||
|
j2eeContainerStartedTime (6) |
INTEGER |
RO |
Seconds |
Startup time of the J2EE server# |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
- #
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
(2) jvmTable
The following table describes jvmTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
jvmTable (2) |
jvmEntry (1) |
jvmIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
None |
|
jvmFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name" |
|||
|
jvmName (3) |
DisplayString |
RO |
-- |
Implementation name of JavaVM |
|||
|
jvmVersion (4) |
DisplayString |
RO |
-- |
Implementation version of JavaVM |
|||
|
jvmCurrentFreeMemory (5) |
Gauge |
RO |
KB |
Free memory requirement of JavaVM (current value) |
|||
|
jvmFreeMemoryHighWaterMark (6) |
Gauge |
RO |
KB |
Free memory requirement of JavaVM (maximum value) |
|||
|
jvmFreeMemoryLowWaterMark (7) |
Gauge |
RO |
KB |
Free memory requirement of JavaVM (minimum value) |
|||
|
jvmFreeMemoryAverag (8) |
Gauge |
RO |
KB |
Free memory requirement of JavaVM (average value#1) |
|||
|
jvmFreeMemoryPeak (9) |
Gauge |
RO |
KB |
Free memory requirement of JavaVM (peak value#2) |
|||
|
jvmCurrentTotalMemory (10) |
Gauge |
RO |
KB |
Current value of the total memory requirement of JavaVM (total of the used memory requirement and free memory requirement) |
|||
|
jvmTotalMemoryHighWaterMark (11) |
Gauge |
RO |
KB |
Maximum value of the total memory requirement of JavaVM (total of the used memory requirement and free memory requirement) |
|||
|
jvmTotalMemoryLowWaterMark (12) |
Gauge |
RO |
KB |
Minimum value of the total memory requirement of JavaVM (total of the used memory requirement and free memory requirement) |
|||
|
jvmTotalMemoryAverage (13) |
Gauge |
RO |
KB |
Average value#1 of the total memory requirement of JavaVM (total of the used memory requirement and free memory requirement) |
|||
|
jvmTotalMemoryPeak (14) |
Gauge |
RO |
KB |
Peak value#2 of the total memory requirement of JavaVM (total of the used memory requirement and free memory requirement) |
|||
|
jvmMaxMemory (15) |
INTEGER |
RO |
KB |
If maximum used memory requirement of JavaVM is not specified, assume (263-1)/210 |
|||
|
jvmStatisticsStartedTime (16) |
INTEGER |
RO |
Seconds |
Statistics start time#3 |
|||
|
jvmSamplingTime (17) |
INTEGER |
RW |
Seconds |
Statistics sampling time#4 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Peak value at the point of value acquisition request
This peak value is the maximum value for the available period of the sampling time after recording.
- #3
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #4
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(3) transactionTable
The following table describes transactionTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
transactionTable (3) |
transactionEntry (1) |
transactionIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The transaction must be started |
|
transactionFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name" |
|||
|
transactionDefaultTransactionTimeout (3) |
INTEGER |
RO |
Seconds |
Default value of transaction timeout |
|||
|
transactionActiveTransactionCount (4) |
Gauge |
RO |
-- |
Number of active transactions (current value) |
|||
|
transactionAveTime (5) |
Gauge |
RO |
Milliseconds |
Transaction time (average value#1) |
|||
|
transactionStatisticsStartedTime (6) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
transactionSamplingTime (7) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(4) httpServerTable
The following table describes httpServerTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
httpServerTable (4) |
httpServerEntry (1) |
httpServerIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
None |
|
httpServerFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name" |
|||
|
httpServerPortNumber (3) |
INTEGER |
RO |
-- |
Port number of the server for management |
|||
|
httpServerActiveThreadCountHighWaterMark (4) |
Gauge |
RO |
-- |
Number of active threads (maximum value) |
|||
|
httpServerActiveThreadCountLowWaterMark (5) |
Gauge |
RO |
-- |
Number of active threads (minimum value) |
|||
|
httpServerActiveThreadCountAverage (6) |
Gauge |
RO |
-- |
Number of active threads (average value#1) |
|||
|
httpServerActiveThreadCountPeak (7) |
Gauge |
RO |
-- |
Number of active threads (peak value#2) |
|||
|
httpServerStatisticsStartedTime (8) |
INTEGER |
RO |
Seconds |
Statistics start time#3 |
|||
|
httpServerSamplingTime (9) |
INTEGER |
RW |
Seconds |
Statistics sampling time#4 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Peak value at the point of value acquisition request
This peak value is the maximum value for the available period of the sampling time after recording.
- #3
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #4
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(5) httpServerConnectorTable
The following table describes httpServerConnectorTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
httpServer ConnectorTable (5) |
httpServer ConnectorEntry (1) |
httpServerConnectorIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Web server integration functionality is used |
|
httpServerConnectorFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name" |
|||
|
httpServerConnectorPortNumber (3) |
INTEGER |
RO |
-- |
Port used for communication with the Web server |
|||
|
httpServerConnectorBackLogUpperBound (4) |
INTEGER |
RO |
-- |
Backlog of the socket used for communication with the Web server |
|||
|
httpServerConnectorConnectionCount (5) |
Gauge |
RO |
-- |
Number of connections between the Web server and Web container (current value) |
|||
|
httpServerConnectorConnectionCountHighWaterMark (6) |
Gauge |
RO |
-- |
Number of connections between the Web server and Web container (maximum value) |
|||
|
httpServerConnectorConnectionCountLowWaterMark (7) |
Gauge |
RO |
-- |
Number of connections between the Web server and Web container (minimum value) |
|||
|
httpServerConnectorActiveThreadCountUpperBound (8) |
Gauge |
RO |
-- |
Number of active threads (upper-limit value) |
|||
|
httpServerConnectorActiveThreadCountHighWaterMark (9) |
Gauge |
RO |
-- |
Number of active threads (maximum value) |
|||
|
httpServerConnectorActiveThreadCountLowWaterMark (10) |
Gauge |
RO |
-- |
Number of active threads (minimum value) |
|||
|
httpServerConnectorActiveThreadCountAverage (11) |
Gauge |
RO |
-- |
Number of active threads (average value#1) |
|||
|
httpServerConnectorActiveThreadCountPeak (12) |
Gauge |
RO |
-- |
Number of active threads (peak value#2) |
|||
|
httpServerConnectorWaitingRequestCountHighWaterMark (13) |
Gauge |
RO |
-- |
Number of requests awaiting execution based on the upper-limit value set for the running threads (maximum value) |
|||
|
httpServerConnectorWaitingRequestCountLowWaterMark (14) |
Gauge |
RO |
-- |
Number of requests awaiting execution based on the upper-limit value set for the running threads (minimum value) |
|||
|
httpServerConnectorWaitingRequestCountAverage (15) |
Gauge |
RO |
-- |
Number of requests awaiting execution based on the upper-limit value set for the running threads (average value#1) |
|||
|
httpServerConnectorWaitingRequestCountPeak (16) |
Gauge |
RO |
-- |
Number of requests awaiting execution based on the upper-limit value set for the running threads (peak value#2) |
|||
|
httpServerConnectorStatisticsStartedTime (17) |
INTEGER |
RO |
Seconds |
Statistics start time#3 |
|||
|
httpServerConnectorSamplingTime (18) |
INTEGER |
RW |
Seconds |
Statistics sampling time#4 |
|||
|
httpServerConnectorActiveThreadCount (19) |
Gauge |
RO |
-- |
Number of active threads |
|||
|
httpServerConnectorWaitingRequestCount (20) |
Gauge |
RO |
-- |
Number of requests awaiting execution |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Peak value at the point of value acquisition request
This peak value is the maximum value for the available period of the sampling time after recording.
- #3
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #4
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(6) dataSourceTable
The following table describes dataSourceTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
dataSourceTable (6) |
dataSourceEntry (1) |
dataSourceIndex(1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The data source must be imported |
|
dataSourceFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:data-source-name" |
|||
|
dataSourceName (3) |
DisplayString |
RO |
-- |
Data source name |
|||
|
dataSourceAuthenticationType (4) |
INTEGER |
RO |
-- |
Authentication type 0: Authentication of each application 1: Authentication of each container |
|||
|
dataSourceLoginTimeout (5) |
INTEGER |
RO |
Seconds |
Login timeout value |
|||
|
dataSourceUserID (6) |
DisplayString |
RO |
-- |
User ID |
|||
|
dataSourcePoolUpperBound (7) |
INTEGER |
RO |
-- |
Number of connection pools (upper-limit value) |
|||
|
dataSourcePoolLowerBound (8) |
INTEGER |
RO |
-- |
Number of connection pools (lower-limit value) |
|||
|
dataSourceCurrentPoolSize (9) |
Gauge |
RO |
-- |
Number of connection pools (current value) |
|||
|
dataSourceActiveConnectionCount (10) |
Gauge |
RO |
-- |
Number of active connections (current value) |
|||
|
dataSourceFreeConnectionCount (11) |
Gauge |
RO |
-- |
Number of free connections (current value) |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
(7) j2eeApplicationTable
The following table describes j2eeApplicationTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
j2eeApplicationTable (7) |
j2eeApplicationEntry (1) |
j2eeApplicationIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The J2EE application (EAR) must be started |
|
j2eeApplicationFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name"# |
|||
|
j2eeApplicationName (3) |
DisplayString |
RO |
-- |
J2EE application name |
|||
|
j2eeApplicationDeployedTime (4) |
INTEGER |
RO |
Seconds |
Time of deployment |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
- #
-
When you start an application in the test mode,
the fully qualified name becomes"logical-server-name:J2EE-application-name_TEST".
(8) ejbApplicationTable
The following table describes ejbApplicationTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
ejbApplicationTable (8) |
ejbApplicationEntry (1) |
ejbApplicationIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The EJB application (EJB-JAR) must be started |
|
ejbApplicationFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name" |
|||
|
ejbApplicationName (3) |
DisplayString |
RO |
-- |
EJB application name (EJB-JAR name) |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
(9) statelessSessionBeanTable
The following table describes statelessSessionBeanTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statelessSessionBeanTable (9) |
statelessSessionBeanEntry (1) |
statelessSessionBeanIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
A Stateless Session Bean is used |
|
statelessSessionBeanFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name" |
|||
|
statelessSessionBeanName (3) |
DisplayString |
RO |
-- |
Enterprise Bean name |
|||
|
statelessSessionBeanHomeInterfaceName (4) |
DisplayString |
RO |
-- |
RemoteHome interface class name#1 |
|||
|
statelessSessionBeanRemoteInterfaceName (5) |
DisplayString |
RO |
-- |
RemoteComponent interface class name#1 |
|||
|
statelessSessionBeanLocalHomeInterfaceName (6) |
DisplayString |
RO |
-- |
LocalHome interface class name (EJB2.0 compliant)#2 |
|||
|
statelessSessionBeanLocalComponentInterfaceName (7) |
DisplayString |
RO |
-- |
LocalComponent interface class name (EJB2.0 compliant)#2 |
|||
|
statelessSessionBeanEjbClassName (8) |
DisplayString |
RO |
-- |
EJB class name |
|||
|
statelessSessionBeanPoolUpperBound (9) |
INTEGER |
RO |
-- |
Number of instance pools (upper-limit value) |
|||
|
statelessSessionBeanPoolLowerBound (10) |
INTEGER |
RO |
-- |
Number of instance pools (lower-limit value) |
|||
|
statelessSessionBeanCurrentPoolSize (11) |
Gauge |
RO |
-- |
Number of instance pools (current value) |
|||
|
statelessSessionBeanWaitingSessionCount (12) |
Gauge |
RO |
-- |
Number of sessions waiting to be connected (current value) |
|||
|
statelessSessionBeanActiveSessionBeanCount (13) |
Gauge |
RO |
-- |
Number of active Stateless Session Beans (current value) |
|||
|
statelessSessionBeanFreeSessionBeanCount (14) |
Gauge |
RO |
-- |
Number of free Stateless Session Beans (current value) |
|||
|
statelessSessionBeanFreeSessionTransactionType (15) |
DisplayString |
RO |
-- |
Transaction type "CMT" or "BMT" |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
- #1
-
Displays "" (a null character) only in case of the Local interface.
- #2
-
Displays "" (a null character) only in case of the Remote interface.
(10) statelessSessionBeanHomeTable
The following table describes statelessSessionBeanHomeTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statelessSession BeanHomeTable (10) |
statelessSession BeanHomeEntry (1) |
statelessSessionBeanHomeIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Stateless Session Bean Remote Home Interface is used |
|
statelessSessionBeanHomeFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name" |
|||
|
statelessSessionBeanHomeName (3) |
DisplayString |
RO |
-- |
RemoteHome interface class name |
|||
|
statelessSessionBeanHomeResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteHome interface (maximum value) |
|||
|
statelessSessionBeanHomeResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteHome interface (minimum value) |
|||
|
statelessSessionBeanHomeResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteHome interface (average value#1) |
|||
|
statelessSessionBeanHomeStatisticsStartedTime (7) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
statelessSessionBeanHomeSamplingTime (8) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(11) statelessSessionBeanRemoteTable
The following table describes statelessSessionBeanRemoteTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statelessSession BeanRemoteTable (11) |
statelessSession BeanRemoteEntry (1) |
statelessSessionBeanRemoteIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Stateless Session Bean Remote Component Interface is used |
|
statelessSessionBeanRemoteFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name" |
|||
|
statelessSessionBeanRemoteName (3) |
DisplayString |
RO |
-- |
RemoteComponent interface class name |
|||
|
statelessSessionBeanRemoteResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteComponent interface (maximum value) |
|||
|
statelessSessionBeanRemoteResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteComponent interface (minimum value) |
|||
|
statelessSessionBeanRemoteResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteComponent interface (average value#1) |
|||
|
statelessSessionBeanRemoteResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the Remote interface (maximum value) |
|||
|
statelessSessionBeanRemoteResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the Remote interface (minimum value) |
|||
|
statelessSessionBeanRemoteResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the Remote interface (average value#1) |
|||
|
statelessSessionBeanRemoteStatisticsStartedTime (10) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
statelessSessionBeanRemoteSamplingTime (11) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(12) statefulSessionBeanTable
The following table describes statefulSessionBeanTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statefulSession BeanTable (12) |
statefulSession BeanEntry (1) |
statefulSessionBeanIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
A Stateful Session Bean is used |
|
statefulSessionBeanFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name" |
|||
|
statefulSessionBeanName (3) |
DisplayString |
RO |
-- |
Enterprise Bean name |
|||
|
statefulSessionBeanHomeInterfaceName (4) |
DisplayString |
RO |
-- |
RemoteHome interface class name#1 |
|||
|
statefulSessionBeanRemoteInterfaceName (5) |
DisplayString |
RO |
-- |
RemoteComponent interface class name#1 |
|||
|
statefulSessionBeanLocalHomeInterfaceName (6) |
DisplayString |
RO |
-- |
LocalHome interface class name#2 |
|||
|
statefulSessionBeanLocalComponentInterfaceName (7) |
DisplayString |
RO |
-- |
LocalComponent interface class name#2 |
|||
|
statefulSessionBeanEjbClassName (8) |
DisplayString |
RO |
-- |
EJB class name |
|||
|
statefulSessionBeanSessionUpperBound (9) |
INTEGER |
RO |
-- |
Number of concurrent connections (upper-limit value) |
|||
|
statefulSessionBeanActiveSessionUpperBound (10) |
INTEGER |
RO |
-- |
Number of concurrent executions (upper-limit value) |
|||
|
statefulSessionBeanPassivateTimeout (11) |
INTEGER |
RO |
Seconds |
Timeout value of a passive session |
|||
|
statefulSessionBeanActiveTimeout (12) |
INTEGER |
RO |
Seconds |
Timeout value of an active session |
|||
|
statefulSessionBeanCurrentSessionCount (13) |
Gauge |
RO |
-- |
Number of connected sessions (current value) |
|||
|
statefulSessionBeanWaitingSessionCount (14) |
Gauge |
RO |
-- |
Number of sessions waiting to be connected (current value) |
|||
|
statefulSessionBeanActiveSessionCount (15) |
Gauge |
RO |
-- |
Number of active sessions (current value) |
|||
|
statefulSessionBeanPassiveSessionCount (16) |
Gauge |
RO |
-- |
Number of passive sessions (current value) |
|||
|
statefulSessionBeanTransactionType (17) |
DisplayString |
RO |
-- |
Transaction type "CMT" or "BMT" |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
- #1
-
Displays "" (a null character) only in case of the Local interface.
- #2
-
Displays "" (a null character) only in case of the Remote interface.
(13) statefulSessionBeanHomeTable
The following table describes statefulSessionBeanHomeTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statefulSession BeanHomeTable (13) |
statefulSession BeanHomeEntry (1) |
statefulSessionBeanHomeIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
Stateful Session Bean Remote Home Interface is used |
|
statefulSessionBeanHomeFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name" |
|||
|
statefulSessionBeanHomeName (3) |
DisplayString |
RO |
-- |
RemoteHome interface class name |
|||
|
statefulSessionBeanHomeResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteHome interface (maximum value) |
|||
|
statefulSessionBeanHomeResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteHome interface (minimum value) |
|||
|
statefulSessionBeanHomeResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteHome interface (average value#1) |
|||
|
statefulSessionBeanHomeResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the RemoteHome interface (maximum value) |
|||
|
statefulSessionBeanHomeResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the RemoteHome interface (minimum value) |
|||
|
statefulSessionBeanHomeResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the RemoteHome interface (average value#1) |
|||
|
statefulSessionBeanHomeStatisticsStartedTime (10) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
statefulSessionBeanHomeSamplingTime (11) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(14) statefulSessionBeanRemoteTable
The following table describes statefulSessionBeanRemoteTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statefulSession BeanRemoteTable (14) |
statefulSession BeanRemoteEntry (1) |
statefulSessionBeanRemoteIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Stateful Session Bean Remote Component Interface is used |
|
statefulSessionBeanRemoteFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name" |
|||
|
statefulSessionBeanRemoteName (3) |
DisplayString |
RO |
-- |
RemoteComponent interface class name |
|||
|
statefulSessionBeanRemoteResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteComponent interface (maximum value) |
|||
|
statefulSessionBeanRemoteResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteComponent interface (minimum value) |
|||
|
statefulSessionBeanRemoteResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteComponent interface (average value#1) |
|||
|
statefulSessionBeanRemoteResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the RemoteComponent interface (maximum value) |
|||
|
statefulSessionBeanRemoteResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the RemoteComponent interface (minimum value) |
|||
|
statefulSessionBeanRemoteResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the RemoteComponent interface (average value#1) |
|||
|
statefulSessionBeanRemoteStatisticsStartedTime (10) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
statefulSessionBeanRemoteSamplingTime (11) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(15) entityBeanTable
The following table describes entityBeanTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
entityBeanTable (15) |
entityBeanEntry (1) |
entityBeanIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
An Entity Bean is used |
|
entityBeanFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name" |
|||
|
entityBeanName (3) |
DisplayString |
RO |
-- |
Enterprise Bean name |
|||
|
entityBeanHomeInterfaceName (4) |
DisplayString |
RO |
-- |
RemoteHome interface class name#1 |
|||
|
entityBeanRemoteInterfaceName (5) |
DisplayString |
RO |
-- |
RemoteComponent interface class name#1 |
|||
|
entityBeanLocalHomeInterfaceName (6) |
DisplayString |
RO |
-- |
LocalHome interface class name#2 |
|||
|
entityBeanLocalComponentInterfaceName (7) |
DisplayString |
RO |
-- |
LocalComponent interface class name#2 |
|||
|
entityBeanEjbClassName (8) |
DisplayString |
RO |
-- |
EJB class name |
|||
|
entityBeanPersistenceType (9) |
DisplayString |
RO |
-- |
Persistence type CMP or BMP |
|||
|
entityBeanCacheOption (10) |
DisplayString |
RO |
-- |
Cache model A: Full Cache B: Cache C: No Cache |
|||
|
entityBeanSessionUpperBound (11) |
INTEGER |
RO |
-- |
Number of concurrent connections (upper-limit value) |
|||
|
entityBeanPoolUpperBound (12) |
INTEGER |
RO |
-- |
Number of instance pools (upper-limit value) |
|||
|
entityBeanPoolLowerBound (13) |
INTEGER |
RO |
-- |
Number of instance pools (lower-limit value) |
|||
|
entityBeanCurrentPoolSize (14) |
Gauge |
RO |
-- |
Number of instance pools (current value) |
|||
|
entityBeanSessionTimeout (15) |
INTEGER |
RO |
-- |
Connection timeout value |
|||
|
entityBeanCurrentSessionCount (16) |
Gauge |
RO |
-- |
Number of connected sessions (current value) |
|||
|
entityBeanWaitingSessionCount (17) |
Gauge |
RO |
-- |
Number of sessions waiting to be connected (current value) |
|||
|
entityBeanActiveEntityBeanCount (18) |
Gauge |
RO |
-- |
Number of active Entity Beans (current value) |
|||
|
entityBeanFreeEntityBeanCount (19) |
Gauge |
RO |
-- |
Number of free Entity Beans (current value) |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
- #1
-
Displays "" (a null character) only in case of the Local interface.
- #2
-
Displays "" (a null character) only in case of the Remote interface.
(16) entityBeanHomeTable
The following table describes entityBeanHomeTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
entityBeanHomeTable (16) |
entityBeanHomeEntry (1) |
entityBeanHomeIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Entity Bean Remote Home Interface is used |
|
entityBeanHomeFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name" |
|||
|
entityBeanHomeName (3) |
DisplayString |
RO |
-- |
RemoteHome interface class name |
|||
|
entityBeanHomeResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteHome interface (maximum value) |
|||
|
entityBeanHomeResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteHome interface (minimum value) |
|||
|
entityBeanHomeResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteHome interface (average value#1) |
|||
|
entityBeanHomeResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the RemoteHome interface (maximum value) |
|||
|
entityBeanHomeResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the RemoteHome interface (minimum value) |
|||
|
entityBeanHomeResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the RemoteHome interface (average value#1) |
|||
|
entityBeanHomeStatisticsStartedTime (10) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
entityBeanHomeSamplingTime (11) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(17) entityBeanRemoteTable
The following table describes entityBeanRemoteTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
entityBeanRemoteTable (17) |
entityBeanRemoteEntry (1) |
entityBeanRemoteIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Entity Bean Remote Component Interface is used |
|
entityBeanRemoteFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name" |
|||
|
entityBeanRemoteName (3) |
DisplayString |
RO |
-- |
RemoteComponent interface class name |
|||
|
entityBeanRemoteResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteComponent interface (maximum value) |
|||
|
entityBeanRemoteResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteComponent interface (minimum value) |
|||
|
entityBeanRemoteResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the RemoteComponent interface (average value#1) |
|||
|
entityBeanRemoteResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the RemoteComponent interface (maximum value) |
|||
|
entityBeanRemoteResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the RemoteComponent interface (minimum value) |
|||
|
entityBeanRemoteResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the RemoteComponent interface (average value#1) |
|||
|
entityBeanRemoteStatisticsStartedTime (10) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
entityBeanRemoteSamplingTime (11) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(18) webApplicationTable
The following table describes webApplicationTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
webApplicationTable (18) |
webApplicationEntry (1) |
webApplicationIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
A Web application (WAR) is used |
|
webApplicationFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:Context-root" |
|||
|
webApplicationContextRoot (3) |
DisplayString |
RO |
-- |
Context root |
|||
|
webApplicationActiveSessionCount (4) |
Gauge |
RO |
-- |
Number of active sessions (current value) |
|||
|
webApplicationTotalJSPServiceCount (5) |
Counter |
RO |
-- |
Number of JSP executions (total value) |
|||
|
webApplicationTotalJSPServiceFailedCount (6) |
Counter |
RO |
-- |
Number of failed JSP executions (total value) |
|||
|
webApplicationTotalJSPServiceMaxTime (7) |
Gauge |
RO |
Milliseconds |
JSP execution time (maximum value) |
|||
|
webApplicationTotalJSPServiceMinTime (8) |
Gauge |
RO |
Milliseconds |
JSP execution time (minimum value) |
|||
|
webApplicationTotalJSPServiceAveTime (9) |
Gauge |
RO |
Milliseconds |
JSP execution time (average value#1) |
|||
|
webApplicationTotalJSPServicePeak (10) |
Gauge |
RO |
Milliseconds |
JSP execution time (peak value#2) |
|||
|
webApplicationTotalJSPServiceOutputDataSizeMax (11) |
Gauge |
RO |
KB |
JSP output data size (maximum value) |
|||
|
webApplicationTotalJSPServiceOutputDataSizeMin (12) |
Gauge |
RO |
KB |
JSP output data size (minimum value) |
|||
|
webApplicationTotalJSPServiceOutputDataSizeAve (13) |
Gauge |
RO |
KB |
JSP output data size (average value#1) |
|||
|
webApplicationTotalJSPServiceOutputDataSizePeak (14) |
Gauge |
RO |
KB |
JSP output data size (peak value#2) |
|||
|
webApplicationTotalStaticFileServiceCount (15) |
Counter |
RO |
-- |
Number of times of accessing static contents (total value) |
|||
|
webApplicationTotalStaticFileServiceFailedCount (16) |
Counter |
RO |
-- |
Number of times of accessing failed static contents (total value) |
|||
|
webApplicationTotalStaticFileServiceMaxTime (17) |
Gauge |
RO |
Milliseconds |
Processing time for static contents acquisition (maximum value) |
|||
|
webApplicationTotalStaticFileServiceMinTime (18) |
Gauge |
RO |
Milliseconds |
Processing time for static contents acquisition (minimum value) |
|||
|
webApplicationTotalStaticFileServiceAveTime (19) |
Gauge |
RO |
Milliseconds |
Processing time for static contents acquisition (average value#1) |
|||
|
webApplicationTotalStaticFileServicePeak (20) |
Gauge |
RO |
Milliseconds |
Processing time for static contents acquisition (peak value#2) |
|||
|
webApplicationTotalStaticFileServiceOutputDataSizeMax (21) |
Gauge |
RO |
KB |
Static contents output data size (maximum value) |
|||
|
webApplicationTotalStaticFileServiceOutputDataSizeMin (22) |
Gauge |
RO |
KB |
Static contents output data size (minimum value) |
|||
|
webApplicationTotalStaticFileServiceOutputDataSizeAve (23) |
Gauge |
RO |
KB |
Static contents output data size (average value#1) |
|||
|
webApplicationTotalStaticFileServiceOutputDataSizePeak (24) |
Gauge |
RO |
KB |
Static contents output data size (peak value#2) |
|||
|
webApplicationStatisticsStartedTime (25) |
INTEGER |
RO |
Seconds |
Statistics start time#3 |
|||
|
webApplicationSamplingTime (26) |
INTEGER |
RW |
Seconds |
Statistics sampling time#4 |
|||
|
webApplicationExclusiveThreadCountUpperBound (27) |
INTEGER |
RO |
-- |
Number of exclusive threads |
|
||
|
webApplicationActiveThreadCountUpperBound (28) |
INTEGER |
RO |
-- |
Number of active threads (upper-limit value) |
|||
|
webApplicationCurrentThreadCountUpperBound (29) |
Gauge |
RO |
-- |
Number of active threads (current upper-limit value#5) |
|||
|
webApplicationActiveThreadCount (30) |
Gauge |
RO |
-- |
Number of active threads (current value) |
|||
|
webApplicationActiveThreadCountHighWaterMark (31) |
Gauge |
RO |
-- |
Number of active threads (maximum value) |
|||
|
webApplicationActiveThreadCountLowWaterMark (32) |
Gauge |
RO |
-- |
Number of active threads (minimum value) |
|||
|
webApplicationActiveThreadCountAverage (33) |
Gauge |
RO |
-- |
Number of active threads (average value#1) |
|||
|
webApplicationActiveThreadCountPeak (34) |
Gauge |
RO |
-- |
Number of active threads (peak value#2) |
|||
|
webApplicationWaitingRequestCountUpperBound (35) |
INTEGER |
RO |
-- |
Number of requests awaiting execution based on the upper-limit value set for the running threads (upper-limit value) |
|||
|
webApplicationWaitingRequestCount (36) |
Gauge |
RO |
-- |
Number of requests awaiting execution based on the upper-limit value set for the running threads (current value) |
|||
|
webApplicationWaitingRequestCountHighWaterMark (37) |
Gauge |
RO |
-- |
Number of requests awaiting execution based on the upper-limit value set for the running threads (maximum value) |
|||
|
webApplicationWaitingRequestCountLowWaterMark (38) |
Gauge |
RO |
-- |
Number of requests awaiting execution based on the upper-limit value set for the running threads (minimum value) |
|||
|
webApplicationWaitingRequestCountAverage (39) |
Gauge |
RO |
-- |
Number of requests awaiting execution based on the upper-limit value set for the running threads (average value#1) |
|||
|
webApplicationWaitingRequestCountPeak (40) |
Gauge |
RO |
-- |
Number of requests awaiting execution based on the upper-limit value set for the running threads (peak value#2) |
|||
|
webApplicationOverflowRequestCount (41) |
Counter |
RO |
-- |
Number of requests for which an error is returned based on the upper limit value that is set up for pending requests of each URL group and Web application (total value) |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Peak value at the point of value acquisition request
This peak value is the maximum value for the available period of the sampling time after recording.
- #3
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #4
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
- #5
-
Upper-limit value for the number of threads that can be concurrently executed at present
(19) servletTable
The following table describes servletTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
servletTable (19) |
servletEntry (1) |
servletIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
A servlet is used |
|
servletFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:context-root:Servlet-class-name" |
|||
|
servletName (3) |
DisplayString |
RO |
-- |
Servlet name coded in web.xml Null character if the servlet name is not set |
|||
|
servletServletClassName (4) |
DisplayString |
RO |
-- |
Servlet class name |
|||
|
servletServiceCount (5) |
Counter |
RO |
-- |
Number of executions of the servlet (total value) |
|||
|
servletServiceFailedCount (6) |
Counter |
RO |
-- |
Number of failed executions of the servlet (total value) |
|||
|
servletServiceMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the servlet (maximum value) |
|||
|
servletServiceMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the servlet (minimum value) |
|||
|
servletServiceAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the servlet (average value#1) |
|||
|
servletServicePeak (10) |
Gauge |
RO |
Milliseconds |
Execution time of the servlet (peak value#2) |
|||
|
servletServiceOutputDataSizeMax (11) |
Gauge |
RO |
KB |
Servlet output data size (maximum value) |
|||
|
servletServiceOutputDataSizeMin (12) |
Gauge |
RO |
KB |
Servlet output data size (minimum value) |
|||
|
servletServiceOutputDataSizeAve (13) |
Gauge |
RO |
KB |
Servlet output data size (average value#1) |
|||
|
servletServiceOutputDataSizePeak (14) |
Gauge |
RO |
KB |
Servlet output data size (peak value#2) |
|||
|
servletStatisticsStartTime (15) |
INTEGER |
RO |
Seconds |
Statistics start time#3 |
|||
|
servletSamplingTime (16) |
INTEGER |
RW |
Seconds |
Statistics sampling time#4 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Peak value at the point of value acquisition request
This peak value is the maximum value for the available period of the sampling time after recording.
- #3
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #4
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(20) requestUrlTable
The following table describes requestUrlTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
requestUrlTable (20) |
requestUrlEntry (1) |
requestUrlIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
Statistics of the requestUrl must be started, and the URL for the corresponding Web application must be accessed |
|
requestUrlFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:context-root:request-URL" |
|||
|
requestUrl (3) |
DisplayString |
RO |
-- |
Request URL |
|||
|
requestUrlServiceCount (4) |
Counter |
RO |
-- |
Number of request executions (total value) |
|||
|
requestUrlServiceFailedCount (5) |
Counter |
RO |
-- |
Number of failed request executions (total value) |
|||
|
requestUrlServiceMaxTime (6) |
Gauge |
RO |
Milliseconds |
Request execution time (maximum value) |
|||
|
requestUrlServiceMinTime (7) |
Gauge |
RO |
Milliseconds |
Request execution time (minimum value) |
|||
|
requestUrlServiceAveTime (8) |
Gauge |
RO |
Milliseconds |
Request execution time (average value#1) |
|||
|
requestUrlServicePeak (9) |
Gauge |
RO |
Milliseconds |
Request execution time (peak value#2) |
|||
|
requestUrlServiceOutputDataSizeMax (10) |
Gauge |
RO |
KB |
Request output data size (maximum value) |
|||
|
requestUrlServiceOutputDataSizeMin (11) |
Gauge |
RO |
KB |
Request output data size (minimum value) |
|||
|
requestUrlServiceOutputDataSizeAve (12) |
Gauge |
RO |
KB |
Request output data size (average value#1) |
|||
|
requestUrlServiceOutputDataSizePeak (13) |
Gauge |
RO |
KB |
Request output data size (peak value#2) |
|||
|
requestUrlStatisticsStartedTime (14) |
INTEGER |
RO |
Seconds |
Statistics start time#3 |
|||
|
requestUrlSamplingTime (15) |
INTEGER |
RW |
Seconds |
Statistics sampling time#4 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Peak value at the point of value acquisition request
This peak value is the maximum value for the available period of the sampling time after recording.
- #3
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #4
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(21) dataSourceFullJTATable
The following table describes dataSourceFullJTATable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
dataSourceFullJTATable (21) |
dataSourceFullJTAEntry (1) |
dataSourceFullJTAIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
Data source (XA) is imported |
|
dataSourceFullJTAFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:data-source-name" |
|||
|
dataSourceFullJTAName (3) |
DisplayString |
RO |
-- |
Data source name |
|||
|
dataSourceFullJTALoginTimeout (4) |
INTEGER |
RO |
Seconds |
Login timeout value |
|||
|
dataSourceFullJTAUserID (5) |
DisplayString |
RO |
-- |
User ID |
|||
|
dataSourceFullJTAPoolUpperBound (6) |
INTEGER |
RO |
-- |
Number of connection pools (upper-limit value) |
|||
|
dataSourceFullJTAPoolLowerBound (7) |
INTEGER |
RO |
-- |
Number of connection pools (lower-limit value) |
|||
|
dataSourceFullJTACurrentPoolSize (8) |
Gauge |
RO |
-- |
Number of connection pools (current value) |
|||
|
dataSourceFullJTAActiveConnectionCount (9) |
Gauge |
RO |
-- |
Number of active connections (current value) |
|||
|
dataSourceFullJTAFreeConnectionCount (10) |
Gauge |
RO |
-- |
Number of free connections (current value) |
|||
|
dataSourceFullJTAGetConnectionMaxTime (11) |
Gauge |
RO |
Milliseconds |
Execution time of the getConnection method (maximum value) |
|||
|
dataSourceFullJTAGetConnectionMinTime (12) |
Gauge |
RO |
Milliseconds |
Execution time of the getConnection method (minimum value) |
|||
|
dataSourceFullJTAGetConnectionAveTime (13) |
Gauge |
RO |
Milliseconds |
Execution time of the getConnection method (average value#1) |
|||
|
dataSourceFullJTACreateConnectionMaxTime (14) |
Gauge |
RO |
Milliseconds |
Execution time of the getXAConnection method (maximum value) |
|||
|
dataSourceFullJTACreateConnectionMinTime (15) |
Gauge |
RO |
Milliseconds |
Execution time of the getXAConnection method (minimum value) |
|||
|
dataSourceFullJTACreateConnectionAveTime (16) |
Gauge |
RO |
Milliseconds |
Execution time of the getXAConnection method (average value#1) |
|||
|
dataSourceFullJTAGetConnectionFailedCount (17) |
Counter |
RO |
-- |
Number of failures of the getConnection method |
|||
|
dataSourceFullJTAConnectionErrorCount (18) |
Counter |
RO |
-- |
Number of times a FATAL error occurred in the Connection. Number of times the connectionErrorOccurred method of ConnectionEventListener was invoked. |
|||
|
dataSourceFullJTAStatisticsStartedTime (19) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
dataSourceFullJTASamplingTime (20) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(22) resourceAdapterTable
The following table describes resourceAdapterTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
resourceAdapterTable (22) |
resourceAdapterEntry (1) |
resourceAdapterIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
A resource adapter is used |
|
resourceAdapterFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:resource-adapter-name":container "logical-server-name:J2EE-application-name:resource-adapter-name":application" |
|||
|
resourceAdapterName (3) |
DisplayString |
RO |
-- |
Resource adapter name |
|||
|
resourceAdapterVendorName (4) |
DisplayString |
RO |
-- |
Name of the vendor providing the resource adapter |
|||
|
resourceAdapterSpecVersion (5) |
DisplayString |
RO |
-- |
Used version of the JCA-based resource adapter |
|||
|
resourceAdapterEISType (6) |
DisplayString |
RO |
-- |
EIS type to which the resource adapter connects |
|||
|
resourceAdapterVersion (7) |
DisplayString |
RO |
-- |
Version of the resource adapter |
|||
|
resourceAdapterConnectionFactoryInterfaceName (8) |
DisplayString |
RO |
-- |
Interface class name of ConnectionFactory |
|||
|
resourceAdapterConnectionFactoryImplName (9) |
DisplayString |
RO |
-- |
Implementation class name of ConnectionFactory |
|||
|
resourceAdapterManagedConnectionFactoryImplName (10) |
DisplayString |
RO |
-- |
Implementation class name of ManagedConnectionFactory |
|||
|
resourceAdapterConnectionInterfaceName (11) |
DisplayString |
RO |
-- |
Interface class name of Connection |
|||
|
resourceAdapterConnectionImplName (12) |
DisplayString |
RO |
-- |
Implementation class name of Connection |
|||
|
resourceAdapterTransactionSupport (13) |
DisplayString |
RO |
-- |
Supported transaction models NoTransaction: No transaction LocalTransaction: Local transaction XATransaction: XA transaction |
|||
|
resourceAdapterConfigProperties (14) |
DisplayString |
RO |
-- |
ConfigurationProperty information#1 |
|||
|
resourceAdapterMConCreateCount (15) |
Counter |
RO |
-- |
Number of executions of the createManagedConnection method of ManagedConnectionFactory |
|||
|
resourceAdapterConCreateCount (16) |
Counter |
RO |
-- |
Number of executions of the getConnection method of ManagedConnection |
|||
|
resourceAdapterMConCleanupCount (17) |
Counter |
RO |
-- |
Number of executions of the cleanup method of ManagedConnection |
|||
|
resourceAdapterMConDestroyCount (18) |
Counter |
RO |
-- |
Number of executions of the destroy method of ManagedConnection |
|||
|
resourceAdapterUserId (19) |
DisplayString |
RO |
-- |
User ID |
|||
|
resourceAdapterPoolUpperBound (20) |
INTEGER |
RO |
-- |
Number of connection pools (upper-limit value) |
|||
|
resourceAdapterPoolLowerBound (21) |
INTEGER |
RO |
-- |
Number of connection pools (lower-limit value) |
|||
|
resourceAdapterCurrentPoolSize (22) |
Gauge |
RO |
-- |
Number of connection pools (current value) |
|||
|
resourceAdapterActiveConnectionCount (23) |
Gauge |
RO |
-- |
Number of active connections (current value) |
|||
|
resourceAdapterFreeConnectionCount (24) |
Gauge |
RO |
-- |
Number of free connections (current value) |
|||
|
resourceAdapterGetConnectionMaxTime (25) |
Gauge |
RO |
Milliseconds |
Execution time of the allocateConnection method of ConnectionManager (maximum value) |
|||
|
resourceAdapterGetConnectionMinTime (26) |
Gauge |
RO |
Milliseconds |
Execution time of the allocateConnection method of ConnectionManager (minimum value) |
|||
|
resourceAdapterGetConnectionAveTime (27) |
Gauge |
RO |
Milliseconds |
Execution time of the allocateConnection method of ConnectionManager (average value#2) |
|||
|
resourceAdapterCreateConnectionMaxTime (28) |
Gauge |
RO |
Milliseconds |
Execution time of the createManagedConnection method of ManagedConnectionFactory (maximum value) |
|||
|
resourceAdapterCreateConnectionMinTime (29) |
Gauge |
RO |
Milliseconds |
Execution time of the createManagedConnection method of ManagedConnectionFactory (minimum value) |
|||
|
resourceAdapterCreateConnectionAveTime (30) |
Gauge |
RO |
Milliseconds |
Execution time of the createManagedConnection method of ManagedConnectionFactory (average value#2) |
|||
|
resourceAdapterGetConnectionFailedCount (31) |
Counter |
RO |
-- |
Number of failures of the allocateConnection method |
|||
|
resourceAdapterConnectionErrorCount (32) |
Counter |
RO |
-- |
Number of times a FATAL error occurred in ManagedConnection Number of times the connectionErrorOccurred method of ConnectionEventListener was invoked |
|||
|
resourceAdapterStatisticsStartedTime (33) |
INTEGER |
RO |
Seconds |
Statistics start time#3 |
|||
|
resourceAdapterSamplingTime (34) |
INTEGER |
RW |
Seconds |
Statistics sampling time#4 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
The output format is property-name=property-value:property-name=property-value:.... If the property name or property value includes an equal sign (=), colon (:), and a yen sign (
![[Figure]](GRAPHICS/ZUENG03A.GIF)
), these signs are displayed as \=, \:and \\.
(Example) abc=ab\:bc\=ef\\gh for property name ..."abc" and property value..."ab:bc=ef\gh"
- #2
-
Average value of the past sampling time from the time of value acquisition request.
- #3
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #4
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(23) statelessSessionBeanLocalHomeTable
The following table describes statelessSessionBeanLocalHomeTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statelessSession BeanLocalHomeTable (23) |
statelessSession BeanLocalHomeEntry (1) |
statelessSessionBeanLocalHomeIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Stateless Session Bean Local Home Interface is used |
|
statelessSessionBeanLocalHomeFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name" |
|||
|
statelessSessionBeanLocalHomeName (3) |
DisplayString |
RO |
-- |
LocalHome interface class name |
|||
|
statelessSessionBeanLocalHomeResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalHome interface (maximum value) |
|||
|
statelessSessionBeanLocalHomeResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalHome interface (minimum value) |
|||
|
statelessSessionBeanLocalHomeResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalHome interface (average value#1) |
|||
|
statelessSessionBeanLocalHomeStatisticsStartedTime (7) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
statelessSessionBeanLocalHomeSamplingTime (8) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(24) statelessSessionBeanLocalComponentTable
The following table describes statelessSessionBeanLocalComponentTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statelessSession BeanLocalComponentTable (24) |
statelessSession BeanLocalComponentTable (1) |
statelessSessionBeanLocalComponentIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Stateless Session Bean Local Component Interface is used |
|
statelessSessionBeanLocalComponentFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name" |
|||
|
statelessSessionBeanLocalComponentFullyQualifiedName (3) |
DisplayString |
RO |
-- |
LocalComponent interface class name |
|||
|
statelessSessionBeanLocalComponentResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalComponent interface (maximum value) |
|||
|
statelessSessionBeanLocalComponentResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalComponent interface (minimum value) |
|||
|
statelessSessionBeanLocalComponentResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalComponent interface (average value#1) |
|||
|
statelessSessionBeanLocalComponentResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalComponent interface (maximum value) |
|||
|
statelessSessionBeanLocalComponentResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalComponent interface (minimum value) |
|||
|
statelessSessionBeanLocalComponentResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalComponent interface (average value#1) |
|||
|
statelessSessionBeanLocalComponentStatisticsStartedTime (10) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
statelessSessionBeanLocalComponentSamplingTime (11) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(25) statefulSessionBeanLocalHomeTable
The following table describes statefulSessionBeanLocalHomeTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statefulSession BeanLocalHomeTable (25) |
statefulSession BeanLocalHomeEntry (1) |
statefulSessionBeanLocalHomeIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Stateful Session Bean Local Home Interface is used |
|
statefulSessionBeanLocalHomeFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name" |
|||
|
statefulSessionBeanLocalHomeName (3) |
DisplayString |
RO |
-- |
LocalHome interface class name |
|||
|
statefulSessionBeanLocalHomeResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalHome interface (maximum value) |
|||
|
statefulSessionBeanLocalHomeResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalHome interface (minimum value) |
|||
|
statefulSessionBeanLocalHomeResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalHome interface (average value#1) |
|||
|
statefulSessionBeanLocalHomeResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalHome interface (maximum value) |
|||
|
statefulSessionBeanLocalHomeResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalHome interface (minimum value) |
|||
|
statefulSessionBeanLocalHomeResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalHome interface (average value#1) |
|||
|
statefulSessionBeanLocalHomeStatisticsStartedTime (10) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
statefulSessionBeanLocalHomeSamplingTime (11) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(26) statefulSessionBeanLocalComponentTable
The following table describes statefulSessionBeanLocalComponentTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statefulSession BeanLocalComponentTable (26) |
statefulSession BeanLocalComponentEntry (1) |
statefulSessionBeanLocalComponentIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Stateful Session Bean Local Component Interface is used |
|
statefulSessionBeanLocalComponentFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name" |
|||
|
statefulSessionBeanLocalComponentName (3) |
DisplayString |
RO |
-- |
LocalComponent interface class name |
|||
|
statefulSessionBeanLocalComponentResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalComponent interface (maximum value) |
|||
|
statefulSessionBeanLocalComponentResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalComponent interface (minimum value) |
|||
|
statefulSessionBeanLocalComponentResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalComponent interface (average value#1) |
|||
|
statefulSessionBeanLocalComponentResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalComponent interface (maximum value) |
|||
|
statefulSessionBeanLocalComponentResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalComponent interface (minimum value) |
|||
|
statefulSessionBeanLocalComponentResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalComponent interface (average value#1) |
|||
|
statefulSessionBeanLocalComponentStatisticsStartedTime (10) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
statefulSessionBeanLocalComponentSamplingTime (11) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(27) entityBeanLocalHomeTable
The following table describes entityBeanLocalHomeTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
entityBeanLocalHomeTable (27) |
entityBeanLocalHomeEntry (1) |
entityBeanLocalHomeIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Entity Bean Local Home Interface is used |
|
entityBeanLocalHomeFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name" |
|||
|
entityBeanLocalHomeName (3) |
DisplayString |
RO |
-- |
LocalHome interface class name |
|||
|
entityBeanLocalHomeResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalHome interface (maximum value) |
|||
|
entityBeanLocalHomeResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalHome interface (minimum value) |
|||
|
entityBeanLocalHomeResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalHome interface (average value#1) |
|||
|
entityBeanLocalHomeResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalHome interface (maximum value) |
|||
|
entityBeanLocalHomeResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocaHome interface (minimum value) |
|||
|
entityBeanLocalHomeResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocaHome interface (average value#1) |
|||
|
entityBeanLocalHomeStatisticsStartedTime (10) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
entityBeanLocalHomeSamplingTime (11) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(28) entityBeanLocalComponentTable
The following table describes entityBeanLocalComponentTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
entityBeanLocal ComponentTable (28) |
entityBeanLocal ComponentEntry (1) |
entityBeanLocalComponentIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Entity Bean Local Component Interface is used |
|
entityBeanLocalComponentFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name" |
|||
|
entityBeanLocalComponentName (3) |
DisplayString |
RO |
-- |
LocalComponent interface class name |
|||
|
entityBeanLocalComponentResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalComponent interface (maximum value) |
|||
|
entityBeanLocalComponentResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalComponent interface (minimum value) |
|||
|
entityBeanLocalComponentResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalComponent interface (average value#1) |
|||
|
entityBeanLocalComponentResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalComponent interface (maximum value) |
|||
|
entityBeanLocalComponentResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalComponent interface (minimum value) |
|||
|
entityBeanLocalComponentResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalComponent interface (average value#1) |
|||
|
entityBeanLocalComponentStatisticsStartedTime (10) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
entityBeanLocalComponentSamplingTime (11) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(29) messageDrivenBeanTable
The following table describes messageDrivenBeanTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
messageDrivenBeanTable (29) |
messageDrivenBeanEntry (1) |
messageDrivenBeanIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
A Message-driven Bean is used |
|
messageDrivenBeanFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name" |
|||
|
messageDrivenBeanName (3) |
DisplayString |
RO |
-- |
Enterprise Bean name |
|||
|
messageDrivenBeanEjbClassName (4) |
DisplayString |
RO |
-- |
EJB class name |
|||
|
messageDrivenBeanTransactionType (5) |
DisplayString |
RO |
-- |
Transaction type CMT or BMT |
|||
|
messageDrivenBeanDestinationType (6) |
DisplayString |
RO |
-- |
Destination types Queue: Destination of the Point-To-Point model Topic: Destination of the Publish-Subscribe model |
|||
|
messageDrivenBeanPoolUpperBound (7) |
INTEGER |
RO |
-- |
Number of instance pools (upper-limit value) |
|||
|
messageDrivenBeanCurrentPoolSize (8) |
Gauge |
RO |
-- |
Number of instance pools (current value) |
|||
|
messageDrivenBeanCurrentSessionCount (9) |
Gauge |
RO |
-- |
Number of connected sessions (current value) |
|||
|
messageDrivenBeanResponseEjbMaxTime (10) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method (maximum value) |
|||
|
messageDrivenBeanResponseEjbMinTime (11) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method (minimum value) |
|||
|
messageDrivenBeanResponseEjbAveTime (12) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method (average value#1) |
|||
|
messageDrivenBeanStatisticsStartedTime (10) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
messageDrivenBeanSamplingTime (11) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(30) queueTable
The following table describes queueTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
queueTable (30) |
queueEntry (1) |
queueIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
None |
|
queueFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:queue-name" |
|||
|
queueName (3) |
DisplayString |
RO |
-- |
Queue name |
|||
|
queueStatus (4) |
DisplayString |
RO |
-- |
Status scheduling:State in which scheduling is possible preparing: Preparation in progress stopping: Queue being terminated closing[in]:Locking the queue entry closing[out]: Locking the queue exit |
|||
|
queueSharedApplicationCount (5) |
INTEGER |
RO |
-- |
Number of applications sharing the queue |
|||
|
queueStayedRequestCount (6) |
Gauge |
RO |
-- |
Number of requests retained in the queue |
|||
|
queueStayedRequestMax (7) |
Gauge |
RO |
-- |
Maximum number of requests retained in the queue |
|||
|
queueLength (8) |
INTEGER |
RO |
-- |
Number of requests that can be registered concurrently |
|||
|
queueLookupName (9) |
DisplayString |
RO |
-- |
Registered name information managed by the queue |
|||
|
queueInterfaceName (10) |
DisplayString |
RO |
-- |
Interface information managed by the queue |
|||
|
queueParallelCount (11) |
INTEGER |
RO |
-- |
Number of concurrent executions managed by the queue |
|||
|
queueTotalThreadCount (12) |
INTEGER |
RO |
-- |
Total number of current resident threads managed by the queue |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
(31) statelessSessionBeanHomeMethodTable
The following table describes statelessSessionBeanHomeMethodTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statelessSessionBean HomeMethodTable (31) |
statelessSessionBean HomeMethodEntry (1) |
statelessSessionBeanHomeMethodIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Stateless Session Bean Remote Home Interface Method is used |
|
statelessSessionBeanHomeMethodFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name:Home-interface-class-name:method-name" |
|||
|
statelessSessionBeanHomeMethodName (3) |
DisplayString |
RO |
-- |
Method name |
|||
|
statelessSessionBeanHomeMethodResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the Home interface (maximum value) |
|||
|
statelessSessionBeanHomeMethodResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the Home interface (minimum value) |
|||
|
statelessSessionBeanHomeMethodResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the Home interface (average value#1) |
|||
|
statelessSessionBeanHomeMethodResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the Home interface (maximum value) |
|||
|
statelessSessionBeanHomeMethodResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the Home interface (minimum value) |
|||
|
statelessSessionBeanHomeMethodResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the Home interface (average value#1) |
|||
|
statelessSessionBeanHomeMethodCallCount (10) |
Counter |
RO |
-- |
Number of executions of the method |
|||
|
statelessSessionBeanHomeMethodStatisticsStartedTime (11) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
statelessSessionBeanHomeMethodSamplingTime (12) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(32) statelessSessionBeanRemoteMethodTable
The following table describes statelessSessionBeanRemoteMethodTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statelessSessionBean RemoteMethodTable (32) |
statelessSessionBean RemoteMethodEntry (1) |
statelessSessionBeanRemoteMethodIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Stateless Session Bean Remote Component Interface Method is used |
|
statelessSessionBeanRemoteMethodFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name:Remote-interface-class-name:method-name" |
|||
|
statelessSessionBeanRemoteMethodName (3) |
DisplayString |
RO |
-- |
Method name |
|||
|
statelessSessionBeanRemoteMethodResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the Remote interface (maximum value) |
|||
|
statelessSessionBeanRemoteMethodResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the Remote interface (minimum value) |
|||
|
statelessSessionBeanRemoteMethodResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the Remote interface (average value#1) |
|||
|
statelessSessionBeanRemoteMethodResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the Remote interface (maximum value) |
|||
|
statelessSessionBeanRemoteMethodResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the Remote interface (minimum value) |
|||
|
statelessSessionBeanRemoteMethodResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the Remote interface (average value#1) |
|||
|
statelessSessionBeanRemoteMethodCallCount (10) |
Counter |
RO |
-- |
Number of executions of the method |
|||
|
statelessSessionBeanRemoteMethodStatisticsStartedTime (11) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
statelessSessionBeanRemoteMethodSamplingTime (12) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(33) statelessSessionBeanLocalHomeMethodTable
The following table describes statelessSessionBeanLocalHomeMethodTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statelessSessionBean LocalHomeMethodTable (33) |
statelessSessionBean LocalHomeMethodEntry (1) |
statelessSessionBeanLocalHomeMethodIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Stateless Session Bean Local Home Interface Method is used |
|
statelessSessionBeanLocalHomeMethodFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name:LocalHome-interface-class-name:method-name" |
|||
|
statelessSessionBeanLocalHomeMethodName (3) |
DisplayString |
RO |
-- |
Method name |
|||
|
statelessSessionBeanLocalHomeMethodResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalHome interface (maximum value) |
|||
|
statelessSessionBeanLocalHomeMethodResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalHome interface (minimum value) |
|||
|
statelessSessionBeanLocalHomeMethodResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalHome interface (average value#1) |
|||
|
statelessSessionBeanLocalHomeMethodResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalHome interface (maximum value) |
|||
|
statelessSessionBeanLocalHomeMethodResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalHome interface (minimum value) |
|||
|
statelessSessionBeanLocalHomeMethodResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalHome interface (average value#1) |
|||
|
statelessSessionBeanLocalHomeMethodCallCount (10) |
Counter |
RO |
-- |
Number of executions of the method |
|||
|
statelessSessionBeanLocalHomeMethodStatisticsStartedTime (11) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
statelessSessionBeanLocalHomeMethodSamplingTime (12) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(34) statelessSessionBeanLocalComponentMethodTable
The following table describes statelessSessionBeanLocalComponentMethodTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statelessSessionBean LocalComponentMethodTable (34) |
statelessSessionBean LocalComponentMethodEntry (1) |
statelessSessionBeanLocalComponentMethodIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Stateless Session Bean Local Component Interface Method is used |
|
statelessSessionBeanLocalComponentMethodFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name:LocalComponent-interface-class-name:method-name" |
|||
|
statelessSessionBeanLocalComponentMethodName (3) |
DisplayString |
RO |
-- |
Method name |
|||
|
statelessSessionBeanLocalComponentMethodResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalComponent interface (maximum value) |
|||
|
statelessSessionBeanLocalComponentMethodResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalComponent interface (minimum value) |
|||
|
statelessSessionBeanLocalComponentMethodResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalComponent interface (average value#1) |
|||
|
statelessSessionBeanLocalComponentMethodResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalComponent interface (maximum value) |
|||
|
statelessSessionBeanLocalComponentMethodResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalComponent interface (minimum value) |
|||
|
statelessSessionBeanLocalComponentMethodResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalComponent interface (average value#1) |
|||
|
statelessSessionBeanLocalComponentMethodCallCount (10) |
Counter |
RO |
-- |
Number of executions of the method |
|||
|
statelessSessionBeanLocalComponentMethodStatisticsStartedTime (11) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
statelessSessionBeanLocalComponentMethodSamplingTime (12) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(35) statefulSessionBeanHomeMethodTable
The following table describes statefulSessionBeanHomeMethodTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statefulSessionBean HomeMethodTable (35) |
statefulSessionBean HomeMethodEntry (1) |
statefulSessionBeanHomeMethodIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Stateful Session Bean Remote Home Interface Method is used |
|
statefulSessionBeanHomeMethodFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name:Home-interface-class-name:method-name" |
|||
|
statefulSessionBeanHomeMethodName (3) |
DisplayString |
RO |
-- |
Method name |
|||
|
statefulSessionBeanHomeMethodResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the Home interface (maximum value) |
|||
|
statefulSessionBeanHomeMethodResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the Home interface (minimum value) |
|||
|
statefulSessionBeanHomeMethodResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the Home interface (average value#1) |
|||
|
statefulSessionBeanHomeMethodResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the Home interface (maximum value) |
|||
|
statefulSessionBeanHomeMethodResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the Home interface (minimum value) |
|||
|
statefulSessionBeanHomeMethodResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the Home interface (average value#1) |
|||
|
statefulSessionBeanHomeMethodCallCount (10) |
Counter |
RO |
-- |
Number of executions of the method |
|||
|
statefulSessionBeanHomeMethodStatisticsStartedTime (11) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
statefulSessionBeanHomeMethodSamplingTime (12) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(36) statefulSessionBeanRemoteMethodTable
The following table describes statefulSessionBeanRemoteMethodTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statefulSessionBean RemoteMethodTable (36) |
statefulSessionBean RemoteMethodEntry (1) |
statefulSessionBeanRemoteMethodIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Stateful Session Bean Remote Component Interface Method is used |
|
statefulSessionBeanRemoteMethodFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name:Remote-interface-class-name:method-name" |
|||
|
statefulSessionBeanRemoteMethodName (3) |
DisplayString |
RO |
-- |
Method name |
|||
|
statefulSessionBeanRemoteMethodResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the Remote interface (maximum value) |
|||
|
statefulSessionBeanRemoteMethodResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the Remote interface (minimum value) |
|||
|
statefulSessionBeanRemoteMethodResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the Remote interface (average value#1) |
|||
|
statefulSessionBeanRemoteMethodResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the Remote interface (maximum value) |
|||
|
statefulSessionBeanRemoteMethodResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the Remote interface (minimum value) |
|||
|
statefulSessionBeanRemoteMethodResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the Remote interface (average value#1) |
|||
|
statefulSessionBeanRemoteMethodCallCount (10) |
Counter |
RO |
-- |
Number of executions of the method |
|||
|
statefulSessionBeanRemoteMethodStatisticsStartedTime (11) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
statefulSessionBeanRemoteMethodSamplingTime (12) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(37) statefulSessionBeanLocalHomeMethodTable
The following table describes statefulSessionBeanLocalHomeMethodTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statefulSessionBean LocalHomeMethodTable (37) |
statefulSessionBean LocalHomeMethodEntry (1) |
statefulSessionBeanLocalHomeMethodIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Stateful Session Bean Local Home Interface Method is used |
|
statefulSessionBeanLocalHomeMethodFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name:LocalHome-interface-class-name:method-name" |
|||
|
statefulSessionBeanLocalHomeMethodName (3) |
DisplayString |
RO |
-- |
Method name |
|||
|
statefulSessionBeanLocalHomeMethodResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalHome interface (maximum value) |
|||
|
statefulSessionBeanLocalHomeMethodResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalHome interface (minimum value) |
|||
|
statefulSessionBeanLocalHomeMethodResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalHome interface (average value#1) |
|||
|
statefulSessionBeanLocalHomeMethodResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalHome interface (maximum value) |
|||
|
statefulSessionBeanLocalHomeMethodResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalHome interface (minimum value) |
|||
|
statefulSessionBeanLocalHomeMethodResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalHome interface (average value#1) |
|||
|
statefulSessionBeanLocalHomeMethodCallCount (10) |
Counter |
RO |
-- |
Number of executions of the method |
|||
|
statefulSessionBeanLocalHomeMethodStatisticsStartedTime (11) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
statefulSessionBeanLocalHomeMethodSamplingTime (12) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(38) statefulSessionBeanLocalComponentMethodTable
The following table describes statefulSessionBeanLocalComponentMethodTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
statefulSessionBean LocalComponentMethodTable (38) |
statefulSessionBean LocalComponentMethodEntry (1) |
statefulSessionBeanLocalComponentMethodIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
The Stateful Session Bean Local Component Interface Method is used |
|
statefulSessionBeanLocalComponentMethodFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name:J2EE-application-name:EJB-application-name:Enterprise-Bean-name:LocalComponent-interface-class-name:method-name" |
|||
|
statefulSessionBeanLocalComponentMethodName (3) |
DisplayString |
RO |
-- |
Method name |
|||
|
statefulSessionBeanLocalComponentMethodResponseMaxTime (4) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalComponent interface (maximum value) |
|||
|
statefulSessionBeanLocalComponentMethodResponseMinTime (5) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalComponent interface (minimum value) |
|||
|
statefulSessionBeanLocalComponentMethodResponseAveTime (6) |
Gauge |
RO |
Milliseconds |
Response time of calls to the LocalComponent interface (average value#1) |
|||
|
statefulSessionBeanLocalComponentMethodResponseEjbMaxTime (7) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalComponent interface (maximum value) |
|||
|
statefulSessionBeanLocalComponentMethodResponseEjbMinTime (8) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalComponent interface (minimum value) |
|||
|
statefulSessionBeanLocalComponentMethodResponseEjbAveTime (9) |
Gauge |
RO |
Milliseconds |
Execution time of the EJB method for the LocalComponent interface (average value#1) |
|||
|
statefulSessionBeanLocalComponentMethodCallCount (10) |
Counter |
RO |
-- |
Number of executions of the method |
|||
|
statefulSessionBeanLocalComponentMethodStatisticsStartedTime (11) |
INTEGER |
RO |
Seconds |
Statistics start time#2 |
|||
|
statefulSessionBeanLocalComponentMethodSamplingTime (12) |
INTEGER |
RW |
Seconds |
Statistics sampling time#3 |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Average value of the past sampling time from the time of value acquisition request.
- #2
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #3
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
(39) webContainerTable
The following table describes webContainerTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
webContainerTable (39) |
webContainerEntry (1) |
webContainerIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
None |
|
webContainerFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-server-name" |
|||
|
webContainerServerName (3) |
DisplayString |
RO |
-- |
Server name of the Web container |
|||
|
webContainerStartedTime (4) |
INTEGER |
RO |
Seconds |
Startup time of the Web container#1 |
|||
|
webContainerStatisticsStartedTime (5) |
INTEGER |
RO |
Seconds |
Statistics start time#1 |
|||
|
webContainerSamplingTime (6) |
INTEGER |
RW |
Seconds |
Statistics sampling time#2 |
|||
|
webContainerActiveThreadCountUpperBound (7) |
INTEGER |
RO |
-- |
Upper-limit value of the number of active threads |
|
||
|
webContainerCurrentThreadCountUpperBound (8) |
Gauge |
RO |
-- |
Current upper-limit value of the number of active threads#3 |
|||
|
webContainerActiveThreadCount (9) |
Gauge |
RO |
-- |
Current number of active threads |
|||
|
webContainerActiveThreadCountHighWaterMark (10) |
Gauge |
RO |
-- |
Maximum number of active threads |
|||
|
webContainerActiveThreadCountLowWaterMark (11) |
Gauge |
RO |
-- |
Minimum number of active threads |
|||
|
webContainerActiveThreadCountAverage (12) |
Gauge |
RO |
-- |
Average value#4 of the number of active threads |
|||
|
webContainerActiveThreadCountPeak (13) |
Gauge |
RO |
-- |
Peak value#5of the number of active threads |
|||
|
webContainerWaitingRequestCountUpperBound (14) |
INTEGER |
RO |
-- |
Upper-limit value of the number of requests awaiting execution based on the upper-limit value set for the running threads |
|||
|
webContainerWaitingRequestCount (15) |
Gauge |
RO |
-- |
Current number of requests awaiting execution based on the upper-limit value set for the running threads |
|||
|
webContainerWaitingRequestCountHighWaterMark (16) |
Gauge |
RO |
-- |
Maximum number of requests awaiting execution based on the upper-limit value set for the running threads |
|||
|
webContainerWaitingRequestCountLowWaterMark (17) |
Gauge |
RO |
-- |
Minimum number of requests awaiting execution based on the upper-limit value set for the running threads |
|||
|
webContainerWaitingRequestCountAverage (18) |
Gauge |
RO |
-- |
Average value#4 of the number of requests awaiting execution based on the upper-limit value set for the running threads |
|||
|
webContainerWaitingRequestCountPeak (19) |
Gauge |
RO |
-- |
Peak value#5 of the number of requests awaiting execution based on the upper-limit value set for the running threads |
|||
|
webContainerOverflowRequestCount (20) |
Counter |
RO |
-- |
Total number of requests in which an error is returned based on the upper limit value that is set up for the default pending request |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only
RW: Read-Write
- #1
-
Number of seconds elapsed since 00:00 Jan. 1, 1970 UTC
- #2
-
Setting the sampling time
If you specify 0 or a lesser value, the statistics stops. If you specify a value from 1 to 9, the sampling time is set to the default value (10 seconds) and the statistics starts. If you specify 10 or a higher value, the statistics starts assuming the specified value as the sampling time.
- #3
-
Upper-limit value for the number of threads that can be concurrently executed at present
- #4
-
Average value of the past sampling time from the time of value acquisition request.
- #5
-
Peak value at the point of value acquisition request (the maximum value involving the available period of the sampling time after recording).
(40) queueAppTable
The following table describes queueAppTable:
|
Table name (OID) |
Entry name (OID) |
Metric name (OID) |
TYPE |
R/W |
Unit |
Description |
Preconditions |
|---|---|---|---|---|---|---|---|
|
queueAppTable (40) |
queueAppEntry (1) |
queueAppIndex (1) |
INTEGER |
RO |
-- |
Sequence number [1,...] |
None |
|
queueAppFullyQualifiedName (2) |
DisplayString |
RO |
-- |
Fully qualified name that uniquely identifies an instance "logical-CTM-server-name:queue-name:logical-J2EE-server-name" |
|||
|
queueAppQueueName (3) |
DisplayString |
RO |
-- |
Queue name |
|||
|
queueAppJ2EEName (4) |
DisplayString |
RO |
-- |
Actual J2EE server name |
|||
|
queueAppStartParallelCount (5) |
INTEGER |
RO |
-- |
Number of concurrent executions when the J2EE application is started |
|||
|
queueAppResidentThreadCount (6) |
INTEGER |
RO |
-- |
Number of current resident threads for the J2EE application |
- Legend:
-
R/W:Read-Only/ Read-Write type
--: Not applicable
RO: Read-Only