ssoclustersetup.vbs (Windows only)
- Organization of this page
Format
- To configure an SSO cluster system:
-
(a) When configuring an executing system
ssoclustersetup.vbs -construction -primary shared-folder-name logical-IP-address
(b) When configuring a standby system
ssoclustersetup.vbs -construction -secondary shared-folder-name
- To maintain an SSO cluster system:
-
(a) When specifying the pre-maintenance settings
ssoclustersetup.vbs -beforemaint {-primary|-secondary} shared-folder-name(b) When specifying the post-maintenance settings
ssoclustersetup.vbs -aftermaint {-primary|-secondary} shared-folder-name - To release an SSO cluster system:
ssoclustersetup.vbs -release {-primary|-secondary} shared-folder-name- To configure a JP1 logical host:
-
(a) When setting up a JP1 logical host
ssoclustersetup.vbs -logicalset JP1-logical-host-name
(b) When clearing the settings of a JP1 logical host
ssoclustersetup.vbs -logicalunset
- To set up an action definition file:
ssoclustersetup.vbs -defset logical-IP-address
- To output the command usage:
ssoclustersetup.vbs -h
Function
The ssoclustersetup.vbs command configures and releases SSO, specifies the pre-maintenance settings and post-maintenance settings, sets up and clears a logical host in the JP1 authentication method, and sets up action definition files in an SSO cluster environment. This command is only for Windows.
- Configuring an SSO cluster environment:
-
-
Configuring an executing SSO cluster environment
-
Configuring a standby SSO cluster environment
-
- Specifying the maintenance settings for an SSO cluster environment:
-
-
Specifying the pre-maintenance settings
-
Specifying the post-maintenance settings
-
- Releasing an SSO cluster environment:
-
Release the cluster environment when SSO is uninstalled or SSO operation is switched from the logical host to the physical host.
- Setting up or clearing a logical host in the JP1 authentication method:
-
-
Setting up a logical host in the JP1 authentication method
-
Clearing the settings of a logical host in the JP1 authentication method
-
- Setting up action definition files:
-
Set a logical IP address and NNM cooperation policy.
Options
-construction
Specify this option when you configure an SSO cluster environment. Note that a logical IP address to be specified for this option must be an IPv4 address.
-beforemaint
Specify this option when you specify the settings required for maintenance of SSO before maintaining SSO (an overwrite installation, upgrade installation, or application of a patch). For details, see 7.3 Maintaining an SSO cluster system.
-aftermaint
Specify this option when you specify the settings required for the maintained SSO after maintaining an SSO (an overwrite installation, upgrade installation, or application of a patch). For details, see 7.3 Maintaining an SSO cluster system.
-release
Specify this option when you release an SSO cluster environment.
-logicalset
Specify this option when you use the JP1 authentication method as the authentication method and perform authentication in JP1/Base on a logical host.
-logicalunset
Specify this option when you clear the authentication method on a logical host in the JP1 authentication method.
-defset
Specify this option when you set or change an IPv4 or IPv6 logical IP address that is set in an action definition file. For details, see the snmp-address:, snmp-address-v6:, change-my-address:, and default-disp-address: keys in the action definition file.
-primary
Specify this option when you execute the command in the executing system.
-secondary
Specify this option when you execute the command in the standby system.
shared-folder-name
Specifies an SSO shared folder name on the shared disk.
logical-IP-address
Specifies a logical IP address that SSO uses.
JP1-logical-host-name
Specifies the JP1 logical host name when you use the JP1 authentication method as the authentication method and perform authentication in JP1/Base on a logical host.
-h
Outputs the command usage. This option cannot be specified together with other options.
Return values
|
0 |
Normal termination. |
|
1 |
Execution error such as incorrect arguments |
Notes
-
You must specify cscript at the beginning of the command line to be executed.
-
If the current folder of the command prompt in which the command is executed is not $SSO_BIN, specify the command by using its full pathname following cscript.
-
When you execute this command, you must be able to access the shared disk, except in the following cases:
-
When setting up configuration in the standby system
-
When specifying the pre-maintenance settings in the standby system
-
When specifying the post-maintenance settings in the standby system
-
-
If you execute this command with the -beforemaint option specified, the SSO service stops. If you execute this command with the -aftermaint option specified, the SSO service starts.