1.1.1 Start sequence for the entire Performance Management system
The Performance Management system must be started in the order of monitoring manager, monitoring agent, and monitoring console server.
-
Start PFM - Manager by executing the jpcspm start command on the monitoring manager.
-
Execute the jpcspm start command on each monitoring agent to start PFM - Base and PFM - Agent, or PFM - Base and PFM - RM.
-
Start PFM - Web Console by executing the jpcwstart command on the monitoring console server.
The jpcspm start command and the jpcwstart command start the services for each Performance Management program in sequence. Service dependencies are pre-set in Windows, which means that you do not need to be concerned with the start sequence.
If PFM - Manager or PFM - Base is installed on the same host as PFM - Web Console, their start processes can be linked. For details on how to link start processes, see 1.4 Synchronizing the starting and stopping of PFM - Manager or PFM - Base and PFM - Web Console.
- Reference note:
-
If PFM - Agent or PFM - RM is installed on the same host as PFM - Manager, start the PFM - Manager services first, and then start the PFM - Agent or PFM - RM services.
Notes:
-
When you install version 08-00 or later of a Performance Management program, the setting for the status management function is as follows:
-
After a new installation of version 08-00 or later of PFM - Manager or PFM - Base on a host that does not already have a Performance Management program installed:
Status management function setting: Enabled
-
Other cases#:
Status management function setting: Remains the same
# The following fall under the other cases category:
-
Upgrading version 06-70 to 07-10 of PFM - Manager to version 08-00 or later
-
Performing a new installation of version 08-00 or later of PFM - Manager or PFM - Base in an environment where version 06-70 to 07-00 of PFM - Agent is installed
The setting is disabled because Performance Management versions 06-70 to 07-10 do not have the status management function.
For the procedure to change the settings of the status management function, see 16.3.1 Configuring the status management function.
-
-
If the Agent Collector or Remote Monitor Collector service fails to start, stop the PFM - Agent or PFM - RM services, and check the common message log to identify the cause of the start failure. Restart the PFM - Agent or PFM - RM services after solving the cause of the Agent Collector or Remote Monitor Collector start failure.
-
You can use the health check function with PFM - Manager 08-11 or later. On a host where PFM - Manager version 09-00 or later is installed, the settings of the health check function are as follows:
-
When performing a new installation of PFM - Manager version 09-00 or later in an environment that does not already have PFM - Manager installed:
Health check function settings: Enabled
-
Other cases#:
Health check function settings: Remains the same
#: The following fall under the other cases category:
-
Upgrading version 06-70 to 08-00 of PFM - Manager to version 08-11 or later
-
Performing a new installation of version 08-11 or later of PFM - Manager in an environment where version 06-70 to 07-00 of PFM - Agent is installed
Because 06-70 to 08-00 versions of PFM - Manager do not have the health check function, the setting status in this case becomes invalid. For details on configuring the health check function, see 16.2.1 Configuring the health check function.
-
-
When a new PFM - Agent or PFM - RM is registered with PFM - Manager while both PFM - Manager and PFM - Web Console are running, a temporary communication error may occur, preventing the newly registered PFM - Agent or PFM - RM from being displayed on PFM - Web Console.
In this case, restart PFM - Web Console. If this problem is not solved even after PFM - Web Console is restarted, restart PFM - Manager and PFM - Web Console again in this order.
-
In PFM - Web Console 12-00 or later, the startup process of the service was changed. This might cause the service of version 12-00 or later to take a longer time to start than that of version 11-50 or earlier.