7.6 Control characters
The following table lists the control characters that are not available in the user-created plug-ins.
Code |
Value |
Description |
---|---|---|
00 |
NUL |
NULl (Null) |
01 |
SOH |
Start Of Heading (Start of heading) |
02 |
STX |
Start of TeXt (Start of text) |
03 |
ETX |
End of TeXt (End of text) |
04 |
EOT |
End Of Transmission (End of transmission) |
05 |
ENQ |
ENQuiry (Inquiry) |
06 |
ACK |
ACKnowledge (Acknowledgement) |
07 |
BEL |
BELl (Bell) |
08 |
BS |
Back Space (Back space) |
09 |
HT |
Horizontal Tabulation (Horizontal tabulation) |
0A |
LF |
Line Feed (Line feed) |
0B |
VT |
Vertical Tabulation (Vertical tabulation) |
0C |
FF |
Form Feed (Form feed) |
0D |
CR |
Carriage Return (Return) |
0E |
SO |
Shift Out (Shift Out) |
0F |
SI |
Shift In (Shift In) |
10 |
DLE |
Data Link Escape (Extended data link control) |
11 |
DC1 |
Device Control 1 (Device control 1) |
12 |
DC2 |
Device Control 2 (Device control 2) |
13 |
DC3 |
Device Control 3 (Device control 3) |
14 |
DC4 |
Device Control 4 (Device control 4) |
15 |
NAK |
Negative AcKnowledge (Negative acknowledgement) |
16 |
SYN |
SYNchronous idle (Synchronization signal) |
17 |
ETB |
End of Transmission Block (End of transmission block) |
18 |
CAN |
CANcel (Cancel) |
19 |
EM |
End of Medium (End of medium) |
1A |
SUB |
SUBstitute (Substitution) |
1B |
ESC |
ESCape (Extended) |
1C |
FS |
File Separator (File separator) |
1D |
GS |
Group Separator (Group separator) |
1E |
RS |
Record Separator (Record separator) |
1F |
US |
Unit Separator (Unit separator) |
7F |
DEL |
DELete (Delete) |
80 |
PAD |
PADding character (Padding character) |
81 |
HOP |
High Octet Preset (High Octet Preset) |
82 |
BPH |
Break Permitted Here (Break permission) |
83 |
NBH |
No Break Here (Break prohibition) |
84 |
IND |
INDex (Index) |
85 |
NEL |
NExt Line (New line) |
86 |
SSA |
Start of Selected Area (Start of selected area) |
87 |
ESA |
End of Selected Area (End of selected area) |
88 |
HTS |
Horizontal Tabulation Set (Horizontal tabulation set) |
89 |
HTJ |
Horizontal Tabulation with Justification (Horizontal tabulation set with justification) |
8A |
VTS |
Vertical Tabulation Set (Vertical tabulation set) |
8B |
PLD |
Partial Line Down (Partial line down) |
8C |
PLU |
Partial Line Up (Partial line up) |
8D |
RI |
Reverse line feed (Previous page) |
8E |
SS2 |
Single Shift 2 (Single character shift 2) |
8F |
SS3 |
Single Shift 3 (Single character shift 3) |
90 |
DCS |
Device Control String (Device control string) |
91 |
PU1 |
Private Use 1 (Private use 1) |
92 |
PU2 |
Private Use 2 (Private use 2) |
93 |
STS |
Set Transmit State (Transmission state setting) |
94 |
CCH |
Cancel CHaracter (Cancel character) |
95 |
MW |
Message Waiting (Waiting for message) |
96 |
SPA |
Start of Protected Area (Start of protected area) |
97 |
EPA |
End of Protected Area (End of protected area) |
98 |
SOS |
Start Of String (Start of string) |
99 |
SGCI |
Single Graphic Character Introducer (Start of single graphic character) |
9A |
SCI |
Single Character Introducer (Start of single character) |
9B |
CSI |
Control Sequence Introducer (Start of control sequence) |
9C |
ST |
String Terminator (End of string) |
9D |
OSC |
Operating System Command (OScommand) |
9E |
PM |
Privacy Message (Private message) |
9F |
APC |
Application Program Command (AP command) |