8.5 List of messages
The following table describes a list of messages.
Message ID |
Message details |
Description |
---|---|---|
DWCO1001_I |
Command start. |
Notifies that the command process is started. |
DWCO1002_I |
Command finished. |
Notifies that the command process is completed. |
DWCO1101_E |
An option [{0}] must be specified only once. |
Indicates that multiple options with the same name are specified for the argument of the command. Do not specify multiple options with same name. The option specified multiple times is output to {0}. |
DWCO1102_E |
Arguments must be a pair of an option key and its value. |
Indicates that only the key for an option or only a value is specified for the argument of the command. Specify a key and value pair. |
DWCO1103_E |
Option [{0}] is invalid. |
Indicates that an invalid option was specified for the argument of the command. See 8.4 List of administrator commands and specify a valid option. The specified invalid option is output to {0}. |
DWCO1104_E |
Please specify option [{1}]. |
Indicates that a mandatory option is not specified. Specify the mandatory option. The mandatory option is output to {1}. |
DWCO1105_E |
Please specify option [{1}] within [{0}] characters. |
Indicates that the number of characters specified for the option value exceeds the maximum characters that can be specified. Specify the value for the option in the number of characters equal to or less than the allowed number of characters. |
DWCO1109_E |
The specified files/folders do not exist or cannot be read. (Path:{0}) |
The certificate file does not exist in the specified file or folder or cannot be read. Check if the certificate file exists in the specified file or folder, you have read permission, or the character code for the file is proper. The path to the specified file or folder is output to {0}. |
DWCO1110_E |
Please specify an integer number between [{1}] to [{2}] for option [{3}]. (Value:{0}) |
A value other than an integer in the preset range was specified for the option. Specify an integer in the specifiable range for the option. The value specified for the option is output to {0}. The smallest integer that can be specified for the option is output to {1}, the largest integer that can be specified for the option is output to {2}, and the option is output to {3}. |
DWCO1112_E |
The settings of Command Property File is wrong. (Setting:{0}, Value:{1}) |
There is an error in the command property file (property.xml). Confirm the following:
Correct the data in the item with an error, and then try again. The setting item name is output to {0}, and the set value is output to {1}. |
DWCO1113_E |
The selected files/folders do not exist or cannot be written. (Path:{0}) |
The specified file or folder does not exist or data cannot be written to it. Check if the specified file or folder exists, or if you have write permission. The path to the specified file or folder is output to {0}. |
DWCO1141_E |
Please specify "now" in the [-downloaddate] option. |
Specify now for the option -downloaddate. |
DWCO1201_E |
User authentication failed. |
User authentication for JP1/DH - Server failed. Check the authentication information defined in the command property file. |
DWCO1203_E |
This user cannot use delivery because the user's password expired. |
Unable to send or receive data because the password has expired. Set a new password. |
DWCO1206_E |
You do not have authority to execute. |
The user does not have authority to execute the commands for system administrators. |
DWCO1501_I |
Log files which expires have been deleted. (File name:{0}) |
Notifies that the log file has been deleted. The file name is output to {0}. |
DWCO1502_I |
Failed to delete log files which expires. (File name:{0}) |
Notifies that the deletion of the log file failed. The file name is output to {0}. |
DWCO1701_I |
Got server status. |
Notifies that the server status has been acquired successfully. |
DWCO1702_I |
Got server parameter. |
Notifies that the server parameter has been acquired successfully. |
DWCO1703_I |
Set server parameter. |
Notifies that the server parameter has been set successfully. |
DWCO1704_E |
Failed to read server parameter file. (Details:{0}) |
Check if the server parameter file exists, or if reading of the file is permitted. The detailed reason is output to {0}. |
DWCO1705_E |
Failed to parse an XML. (Details:{0}) |
The format of the server parameter file is invalid. Check and revise the format. The detailed reason is output to {0}. |
DWCO1706_E |
Failed to generate an XML. (Details:{0}) |
Check the detailed reason output to {0} and take necessary action. |
DWCO1707_E |
The XML format is invalid. (Details:{0}) |
The format of the server parameter file is invalid. Check and revise the format. The detailed reason is output to {0}. |
DWCO1708_E |
A setting is wrong. (Setting:{0}, Value:{1}) |
There is an error in the setting items in the server parameter file. Check and review the settings. The setting item name is output to {0}, and the set item is output to {1}. |
DWCO1720_I |
Got user information. |
Notifies that the user information has been acquired successfully. |
DWCO1721_E |
The specified domain does not exist. (Domain:{0}) |
The specified domain does not exist. Check if an existing domain is specified. The domain name is output to {0}. |
DWCO1722_E |
Failed to get user information. (Details:{0}) |
Check if writing to the user information export file is permitted. The detailed reason is output to {0}. |
DWCO1723_I |
Imported user information. |
Notifies that the user information has been imported successfully. |
DWCO1724_E |
Failed to import user information. (Details:{0}) |
Check the detailed reason output to {0} and try again. |
DWCO1725_E |
Failed to import user information. Please refer to the results file for details of the error. (Results file:{0}) |
Import of user information failed. Based on the detailed information output to the result file, correct the user information import file and try again. The result file name is output to {0}. |
DWCO1726_W |
Failed to write a results file. (Details:{0}) |
Check if writing to the result file is permitted. The detailed reason is output to {0}. |
DWCO1730_I |
Got audit log. |
Notifies that the audit log has been acquired successfully. |
DWCO1731_E |
Failed to get audit log. (Details:{0}) |
Acquisition of the audit log failed. See the detailed reason output to {0}, confirm that writing to the audit log file is permitted, and then try again. |
DWCO1732_E |
The specified date is wrong. (Date:{0}) |
Check that the date format is YYYY/MM/DD, and if the date is correct. The date is output to {0}. |
DWCO1735_I |
Extracted a file/folder. |
Notifies that delivery data has been ejects successfully. |
DWCO1736_E |
Failed to Extract a file/folder. (Details:{0}) |
Notifies that delivery data has been ejects failed. The date is output to {0}. |
DWCO1741_I |
Got bandwidth limitation rules. |
Notifies that the Refer to bandwidth limitation rules has been acquired successfully. |
DWCO1742_E |
Failed to get bandwidth limitation rules. (Details:{0}) |
Notifies that the Refer to bandwidth limitation rules has been acquired failed. The date is output to {0}. |
DWCO1743_E |
Failed to output bandwidth limitation rules to an XML file. (PathDetails:{0}) |
Notifies that output of an XML file for the bandwidth limitation rules failed. The date is output to {0}. |
DWCO1745_I |
Set bandwidth limitation rules. |
Notifies that the Refer to bandwidth limitation rules has been set successfully. |
DWCO1746_E |
Failed to set bandwidth limitation rules. (Details:{0}) |
Notifies that the Refer to bandwidth limitation rules has been set failed. The date is output to {0}. |
DWCO1747_E |
Failed to read bandwidth limitation rules file. (Details:{0}) |
Notifies that reading of an XML file for the bandwidth limitation rules failed. The date is output to {0}. |
DWCO1801_I |
Got delivery information. |
Notifies that the delivery information has been acquired successfully. |
DWCO1802_E |
Failed to get delivery information. (Details:{0}) |
Acquisition of the delivery information failed. Check and review the settings based on the detailed reason, and then try again. The detailed reason is output to {0}. |
DWCO1803_E |
Failed to output delivery information to an XML file. (Path:{0}) |
Check if you have write permission for the specified file. The path to the XML file is displayed in {0}. |
DWCO1821_I |
Updated delivery status. (Delivery ID:{0}, File ID:{1}) |
Notifies that the delivery status has been updated successfully. The delivery ID is output to {0}, and the file ID is output to {1}. |
DWCO1822_E |
Failed to update delivery status. It might be caused by the following reasons: The delivery does not exist. The delivery expired. Uploading is not completed. The delivery was not approved. (Delivery ID:{0}, File ID:{1}, Details:{2}) |
Update of the delivery status failed. Check if the relevant delivery exists, if its data storage period has expired, if its transmission was completed, and if its approval process has completed. The delivery ID is output to {0}, the file ID is output to {1}, and the detailed reason is output to {2}. |
DWCO1841_I |
Deleted a delivery. (Delivery ID:{0}) |
Notifies that the delivery has been deleted successfully. The delivery ID is output to {0}. |
DWCO1842_E |
Failed to delete a delivery. It might be caused by the following reasons: The delivery does not exist. Uploading is not completed. The delivery was not approved. (Delivery ID:{0}, Details:{1}) |
A non-existing delivery cannot be deleted. A delivery whose transfer is not completed cannot be deleted. For an unapproved delivery, try again after it is approved. The delivery ID is output to {0}, and the detailed reason is output to {1}. |
DWCO1843_E |
Failed to delete a delivery. The delivery might be sending or downloading. (Delivery ID:{0}, Details:{1}) |
A delivery being in progress of transmission or reception cannot be deleted. The delivery ID is output to {0}, and the detailed reason is output to {1}. |
DWCO1901_E |
An unexpected error occurred. |
An unexpected exception occurred. Load might be concentrated on the server. Try again after a while. If the same error keeps occurring even after some retries, contact our sales representative or support contact. Also, it is possible that the user executing the process might have been deleted in the middle of execution. Contact the representative user or a group manager. |
DWCO1902_E |
Unable to start the application because initialization of logs failed. |
The settings for the log files are invalid. This problem could be solved by re-installation. |
DWCO1903_E |
Unable to start the application because reading message files failed. |
The settings for the configuration file are invalid. This problem could be solved by re-installation. |
DWCO1904_E |
Unable to start the application because reading setting files failed. |
The settings for the configuration file are invalid. This problem could be solved by re-installation. |
DWCO1906_E |
Failed to connect to the server. (Details:{0}) |
See the detailed reason, and then check and review the execution environment such as the network environment again. The detailed reason is output to {0}. |
DWCO1907_E |
The server is busy. Please try again later. |
The server is currently busy, and the HTTP status code 503 (Service Unavailable) is returned. Try again after a while. |
DWCO1908_E |
The session has timed out. Please try again. |
The session is timed out. Log in again. |
DWCO1909_E |
The server returned an error. (Details:{0}) |
See the detailed reason, and then check and review the settings for the user, group, and delivery rules again. The detailed reason is output to {0}. |
DWCO1911_E |
The operation of getting a lock for concurrent control timed out. |
A command is already running in the same computer. Because more than one command cannot be executed simultaneously, try again after the active command ends. If this error message frequently appears, the problem might be solved by setting a longer timeout time. Also, the user might not have the write permission to the Windows temporary folder. Check that the temporary folder is set correctly. |
DWCO1999_E |
Unable to start the application. |
The server is busy, and the service cannot be started. Try again after a while. |
DWCO2002_I |
Suspended running file transfers. (Delivery ID:{0}) |
Notifies that the file transfer process has been suspended. The delivery ID is output to {0}. |
DWCO2005_W |
Running file transfers do not exist. |
Notifies that there was no file transfer process. |
DWCO2006_W |
Running file transfers do not exist. (Delivery ID:{0}) |
Notifies that there was no file transfer process. The delivery ID is output to {0}. |
DWCO2007_I |
The specified delivery was already suspended. (Delivery ID:{0}) |
Notified that the delivery you tried to suspend had already been suspended. The delivery ID is output to {0}. |
DWCO2008_E |
Failed to suspend the specified delivery because it was already canceled. (Delivery ID:{0}) |
You cannot suspend a delivery that has been canceled. The delivery ID is output to {0}. |
DWCO2009_E |
The specified delivery did not exist. (Delivery ID:{0}) |
Notifies that the specified delivery does not exist. Check if the specified delivery ID is correct. The delivery ID is output to {0}. |
DWCO2010_E |
The specified delivery cannot be suspended. (Delivery ID:{0}) |
The specified delivery cannot be suspended because the delivery might already have been sent in the web window. The delivery ID is output to {0}. |
DWCO2022_I |
Canceled running file transfers. (Delivery ID:{0}) |
Notifies that the file transfer process was canceled. The delivery ID is output to {0}. |
DWCO2025_I |
The specified delivery was already canceled. (Delivery ID:{0}) |
Notified that the delivery you attempted to cancel has already been canceled. The delivery ID is output to {0}. |
DWCO2026_E |
Failed to cancel the specified delivery because it was already suspended. (Delivery ID:{0}) |
You cannot cancel a delivery that has been suspended. The delivery ID is output to {0}. |
DWCO2027_E |
The specified delivery cannot be canceled. (Delivery ID:{0}) |
The specified delivery cannot be canceled because the delivery might already have been sent in the web window. The delivery ID is output to {0}. |
DWCO2041_I |
Set acceptance of the file transfer function to deny. |
The delivery acceptance status of the file transfer function has been set to delivery denial. |
DWCO2061_I |
Set acceptance of the file transfer function to allow. |
The delivery acceptance status of the file transfer function has been set to start delivery. |