5.1.2 Specifying the settings for linking to JP1/AJS3

To link JP1/FTP to JP1/AJS3, you must specify the following settings in JP1/AJS3:

Register JP1/FTP as a custom job

Register JP1/FTP into JP1/AJS3 as a custom job so that the job can be used in JP1/AJS3.
Copy the transmission information for JP1/FTP

If the host used to define jobs differs from the host used to execute the jobs, copy the transmission information from the host used to execute jobs into the host used to define jobs.

Organization of this subsection

(1) Registering JP1/FTP as a custom job
(2) Copying the definition program and configuring settings

(1) Registering JP1/FTP as a custom job

To register JP1/FTP into JP1/AJS3 as a custom job in order to link JP1/FTP to JP1/AJS3:

From the Windows Start menu, choose Programs, JP1_Automatic Job Management System 3 - View, and then Register Custom Job.

The Register Custom Job dialog box appears.
Click Add.

The Set Properties of Custom Job dialog box appears.

Set each item and then click OK.

The custom job is registered. The following shows the Set Properties of Custom Job dialog box and the settings.

Figure 5‒2: Set Properties of Custom Job dialog box

Table 5‒1: Settings in the Set Properties of Custom Job dialog box
Item	Setting
Name ((1 to 8-byte character string)) <<blank>>	Specify any name for the custom job. This item is mandatory.
Comment ((0 to 40-byte character string)) <<blank>>	Specify any desired comment. The forward slash (/) and the space cannot be used in a comment.
Defining program	Specify the following definition program name: `JP1/FTP-installation-directory\FTS_CARD.EXE` (fixed) Specify the definition program on the host that is used to define jobs. If JP1/FTP is not installed on the host that is used to define jobs, copy the required files according to the description in (2) Copying the definition program and configuring settings.
Executing program	Specify the name of the following executable program: `JP1/FTP-installation-directory\FTS_JPCS.EXE` (fixed) This executable program must be located on the executing host. If the executable program exists in multiple JP1/AJS3 - Agents and their installation paths are different, specify `$xxx$\name-of-executable-file` (`xxx`: variable). In this case, you must register (define) the variables at the JP1/AJS3 - Agent hosts. For details about the registration method, see the JP1/Automatic Job Management System 3 Linkage Guide. Note that the return value for the executable program is the same as that for the `ftstran` command. See the return value for this command.
Version	`0600` (fixed)
Class	`JP1FTP` (fixed)
Job Type	PC

To Page Top

(2) Copying the definition program and configuring settings

If JP1/FTP is not installed on the host that is used to define jobs, perform the following steps:

Copy the following files to the machine on which JP1/AJS3 - View is installed.

The files must be copied to the following destinations:
- Copy destination for the definition program FTS_CARD.EXE and the DLL file ftslang.dll
  
  The directory specified in Defining program in the Set Properties of Custom Job dialog box.
- Copy destination for the environment settings file ftscard.ini
  
  C:\Program Files\HITACHI\FTSFTP
- Copy destination for the DLL files Fts_card_*.dll and Fts_cmn_msg_*.dll
  
  C:\Program Files\HITACHI\FTSFTP\Lang

In the environment setting file that was copied, configure the environment in which the definition program will run. The following table lists and describes the section, keys, and values that can be specified.

Table 5‒2: Contents of the definition file (ftscard.ini)
Section	Key	Value	Description
`[Language]`	`LangType`	`0x0409\|0x0411` `<<0x0411>>`	Specifies the language to be used. `0x0409`: English. `0x0411`: Japanese.

To Page Top