12.3.10 Define Details - [Remote Jobnet] dialog box (for a root remote jobnet)

Specify a unit name. Use a character string of up to 30 bytes. The default is a blank.

Specify a comment for the unit. Use a character string of up to 80 bytes. The default is a blank.

Specify the execution agent name or execution agent group name to be assigned the task of job execution. Use a character string of up to 255 bytes. The execution agent name or execution agent group name must already be defined in the JP1/AJS3 - Manager you specified in Target manager.

The execution agent name that is used in the job definition differs depending on whether the execution agent is specified for a remote jobnet and whether the execution agent is specified for a job in the remote jobnet.

The following table shows the value used for each specification.

For details about execution agents, see 5.1.1 Execution agents in the manual JP1/Automatic Job Management System 3 Overview.

Cautionary note

If you selected Queueless Agent for Exec. service for a job in the jobnet, specify the execution host name.

Select whether to concurrently execute multiple jobnets. You can specify Disable or Enable. The default is Disable. If you select Enable, you cannot specify Hold if prev. = 'abend' and Hold if prev. = 'warning' or 'abend' for Hold in the Attributes page.

Specify the number of execution result logs to be saved. You can specify 1 to 99. The default is 1. However, to specify the maximum number of logs to keep in the environment setting parameter, you can specify 1 to 999. For details about how to specify the environment setting parameter MAXSAVEGEN, see 20.4.2(78) MAXSAVEGEN in the JP1/Automatic Job Management System 3 Configuration Guide.

Specify the name of the JP1/AJS3 - Manager host to which you want to transfer the root remote jobnet to be run. Use a character string of up to 255 bytes. The default is a blank.

The scheduler service that executes a remote jobnet is determined by the specification of the environment setting parameter REMNETSERVICENAME for JP1/AJS3 - Manager on the host to which the jobnet is to be transferred.

Specify the priority of a job. You can set None, or 1 to 5. The highest priority is 5. The default is None. If the priority of a job is set to None, the priority value set for the environment setting parameter DEFAULTPRIORITY is applied to the job.

In UNIX, if non-root users execute jobs resulting from mapping, specifying the value of 4 or 5 will result in an authority error at the time of job execution.

Specify a time period after which a time-out should occur if a root remote jobnet registered for execution is not executed on the schedule date. The value is the period of time to pass before the Skipped so not exe. status is set up. The specified value is always effective, irrespective of the registration procedure. For immediate registration, the date of registration is used as the date when execution starts. The default is Use system settings.

You can specify one of the following:

• Use system settings

  Executes the jobnet based on the settings of the EXECDEFER environment setting parameter.

• 1 day

  Suppresses remote jobnet execution if one day has passed since the execution schedule date.

• 2 days

  Suppresses remote jobnet execution if two days have passed since the execution schedule date.

• Unlimited

  Waits for hold release, event or execution for an unlimited amount of time.

Dictates how the system handles execution schedules when a jobnet fails to complete before the scheduled start time of the next generation. The default is Schedule skip. You can specify one of the following:

• Schedule skip

  Skips the jobnet execution schedule having the same start time. Then it starts a next-generation jobnet that does not have a conflicting start time.

• Multi-schedule

  Waits until the execution of the current-generation jobnet has been completed, and upon completion, executes the next generation. If Enable is selected for Concurrent exec., executes the next generation at its start time, without waiting for the completion of the current-generation jobnet.

When using the required jobnet execution time to monitor the end delay of the jobnet, select Time-required-for-execution and specify the required jobnet execution time in minutes. You can specify 1 to 2,879. In the default mode, Time-required-for-execution is not selected.

Specify whether to place the unit in the hold status in advance. The default is No. You can specify one of the following:

• No

  Does not hold a remote jobnet.

• Hold if prev. = 'abend'

  If the result of the previous root jobnet execution is "Ended abnormally", "Skipped so not exe.", "Invalid exe. seq.", "Interrupted", or "Killed", this option holds the root jobnet. If you select Enable for Concurrent exec. in the Definition page, you cannot specify this option.

• Hold if prev. = 'warning' or 'abend'

  If the result of the previous root jobnet execution is "Ended abnormally", "Ended with warning", "Skipped so not exe.", "Invalid exe. seq.", "Interrupted", or "Killed", this option holds the root jobnet. If you select Enable for Concurrent exec. in the Definition page, you cannot specify this option.

• Yes

  Holds the remote jobnet.

Set the unit type to Normal or Recovery. The default is Normal.

Specify the owner of the unit. Use a character string of up to 31 bytes. The default is the login JP1 user name. Note that if the upper-level unit-attribute inheritance function has been set for the upper-level jobnet, the default is the owner of the upper-level unit.

Specify a JP1 resource group name. Use a character string of up to 63 bytes. You can specify alphanumeric characters and underscores (_). The default is the JP1 resource group name of the upper-level unit. If you set a blank, you are not authorized to access this group.