Hitachi

JP1 Version 12 JP1/Automatic Job Management System 3 Configuration Guide


22.4.3 Procedure for replicating a virtual machine after setup of JP1/AJS3 - Agent (on the replicated VM)

If you replicate a virtual machine after setting up JP1/AJS3 - Agent, the replication procedure varies depending on whether you change the IP address or host name after replication. If you change the IP address or host name, the procedure also varies depending on which item you change. The following subsections describe the procedure to be performed on the replicated virtual machine in each case:

Organization of this subsection

(1) When changing neither the IP address nor the host name

The following describes the procedure for replicating a virtual machine (after setting up JP1/AJS3 - Agent) that must be performed on the replicated virtual machine when neither the IP address nor the host name is to be changed.

  1. Perform the tasks that are required in JP1/Base after the virtual machine is replicated by performing disk copy installation.

    For the tasks that must be performed in JP1/Base during disk copy installation, see the JP1/Base User's Guide.

  2. To use the agent connection permission configuration file, edit it based on the replication-destination environment.

    For details about the agent connection permission configuration file, see 2.3.9 Restricting hosts that can access JP1/AJS3 in the JP1/Automatic Job Management System 3 System Design (Configuration) Guide.

  3. Enable automatic startup of the JP1/Base and JP1/AJS3 services again based on the operational requirements.

    For details about how to enable automatic startup of the JP1/Base service, see the JP1/Base User's Guide.

    For details about how to enable automatic startup of the JP1/AJS3 service, see 4.2.4 Settings for starting and stopping JP1/AJS3 services automatically in the JP1/Automatic Job Management System 3 System Design (Configuration) Guide.

(2) When changing the IP address only

The following describes the procedure for replicating a virtual machine (after setting up JP1/AJS3 - Agent) that must be performed on the replicated virtual machine when only the IP address is to be changed.

  1. Perform the tasks required in JP1/Base when the IP address is changed.

    For details about the tasks required in JP1/Base when the IP address is changed, see the JP1/Base User's Guide.

  2. Perform the tasks that are required in JP1/Base after the virtual machine is replicated by performing disk copy installation.

    For the tasks that must be performed in JP1/Base during disk copy installation, see the JP1/Base User's Guide.

  3. To use the agent connection permission configuration file, edit it based on the replication-destination environment.

    For details about the agent connection permission configuration file, see 2.3.9 Restricting hosts that can access JP1/AJS3 in the JP1/Automatic Job Management System 3 System Design (Configuration) Guide.

  4. Enable automatic startup of the JP1/Base and JP1/AJS3 services again based on the operational requirements.

    For details about how to enable automatic startup of the JP1/Base service, see the JP1/Base User's Guide.

    For details about how to enable automatic startup of the JP1/AJS3 service, see 4.2.4 Settings for starting and stopping JP1/AJS3 services automatically in the JP1/Automatic Job Management System 3 System Design (Configuration) Guide.

(3) When changing the host name only

The following describes the procedure for replicating a virtual machine (after setting up JP1/AJS3 - Agent) that must be performed on the replicated virtual machine when only the host name is to be changed.

  1. Perform the tasks required in JP1/Base when the host name is changed.

    For details about the tasks required in JP1/Base when the host name is changed, see the JP1/Base User's Guide.

  2. Perform the tasks that are required in JP1/Base after the virtual machine is replicated by performing disk copy installation.

    For the tasks that must be performed in JP1/Base during disk copy installation, see the JP1/Base User's Guide.

  3. To use the agent connection permission configuration file, edit it based on the replication-destination environment.

    For details about the agent connection permission configuration file, see 2.3.9 Restricting hosts that can access JP1/AJS3 in the JP1/Automatic Job Management System 3 System Design (Configuration) Guide.

  4. Enable automatic startup of the JP1/Base and JP1/AJS3 services again based on the operational requirements.

    For details about how to enable automatic startup of the JP1/Base service, see the JP1/Base User's Guide.

    For details about how to enable automatic startup of the JP1/AJS3 service, see 4.2.4 Settings for starting and stopping JP1/AJS3 services automatically in the JP1/Automatic Job Management System 3 System Design (Configuration) Guide.

(4) When changing both the IP address and the host name

The following describes the procedure for replicating a virtual machine (after setting up JP1/AJS3 - Agent) that must be performed on the replicated virtual machine when both the IP address and host name are to be changed.

  1. Perform the tasks required in JP1/Base when the IP address is changed.

    For details about the tasks required in JP1/Base when the IP address is changed, see the JP1/Base User's Guide.

  2. Perform the tasks required in JP1/Base when the host name is changed.

    For details about the tasks required in JP1/Base when the host name is changed, see the JP1/Base User's Guide.

  3. Perform the tasks that are required in JP1/Base after the virtual machine is replicated by performing disk copy installation.

    For the tasks that must be performed in JP1/Base during disk copy installation, see the JP1/Base User's Guide.

  4. To use the agent connection permission configuration file, edit it based on the replication-destination environment.

    For details about the agent connection permission configuration file, see 2.3.9 Restricting hosts that can access JP1/AJS3 in the JP1/Automatic Job Management System 3 System Design (Configuration) Guide.

  5. Enable automatic startup of the JP1/Base and JP1/AJS3 services again based on the operational requirements.

    For details about how to enable automatic startup of the JP1/Base service, see the JP1/Base User's Guide.

    For details about how to enable automatic startup of the JP1/AJS3 service, see 4.2.4 Settings for starting and stopping JP1/AJS3 services automatically in the JP1/Automatic Job Management System 3 System Design (Configuration) Guide.