3.5.1 Extending trace log files

This subsection describes how to extend the following trace log files in Windows:

JP1/AJS3 trace log file
Queueless trace log file
Internal log file for execution of queueless jobs

Organization of this subsection

(1) Extending the JP1/AJS3 trace log file
(2) Extending the queueless trace log file
(3) Extending the internal log file for execution of queueless jobs

(1) Extending the JP1/AJS3 trace log file

The following two types of JP1/AJS3 trace log files exist:

Common scheduler trace log file

The scheduler trace information on the physical host and all logical hosts is output to a single trace log file.
Scheduler trace log file of each scheduler service

The scheduler trace information of scheduler service is output to this log file in units of scheduler service.

The following table describes the initial status of each type of trace log file:

Item	Common scheduler trace log file	Scheduler trace log file of each scheduler service
File name	If the installation folder is the default installation folder or is in a folder protected by the system^#1, the file name is as follows: `%ALLUSERSPROFILE%`^#2`\Hitachi\JP1\JP1_DEFAULT\JP1AJS2\log\tracelog` If the installation folder is other than the above, the file name is as follows: `JP1/AJS3-Manager-installation-folder\log\tracelog`	If the installation folder is the default installation folder or is in a folder protected by the system^#1, the file name is as follows: `%ALLUSERSPROFILE%`^#2`\Hitachi\JP1\JP1_DEFAULT\JP1AJS2\log\tracelog_scheduler-service-name` If the installation folder is other than the above, the file name is as follows: `JP1/AJS3-Manager-installation-folder\log\tracelog_scheduler-service-name`
Size	The size that allows the file to contain the trace log for about 2,000 executed jobs. Specifically, the size is set to 20 megabytes (20,480 kilobytes).	The size (per file) that allows the file to contain the trace log for about 2,000 executed jobs. Specifically, the size of each file is set to 20 megabytes (20,480 kilobytes).

#1:

A folder protected by the system is a folder under any of the following:

- system-drive\Windows

- system-drive\Program Files

- system-drive\Program Files (x86)

#2:

The default value for %ALLUSERSPROFILE% is system-drive\ProgramData.

The required trace log file size differs greatly depending on the jobnet structure, the number of JP1/AJS3 - View connections, and the nature of the operations. The method to estimate trace log file size also differs depending on whether scheduler trace log files are to be generated for individual scheduler services. Estimate an appropriate size for the trace log file and expand the current size if necessary.

For details about how to estimate an appropriate trace log file size, see 3.4.2 Estimating the size of the scheduler trace log file in the JP1/Automatic Job Management System 3 System Design (Configuration) Guide.

If the trace log file size must be extended, use the ajstrsetsz command to resize the file. For details about the ajstrsetsz command, see ajstrsetsz in 3. Commands Used for Normal Operations in the manual JP1/Automatic Job Management System 3 Command Reference.

To Page Top

(2) Extending the queueless trace log file

The initial settings for the queueless trace log file are as follows:

File name

If the installation folder is the default installation folder or is in a folder protected by the system, the file name is as follows:

%ALLUSERSPROFILE%\Hitachi\JP1\JP1_DEFAULT\JP1AJS2\log\tracelog.ql

The default value for %ALLUSERSPROFILE% is system-drive\ProgramData.

A folder protected by the system is a folder under any of the following:

- system-drive\Windows

- system-drive\Program Files

- system-drive\Program Files (x86)

If the installation folder is other than the above, the file name is as follows:

JP1/AJS3-installation-folder\log\tracelog.ql
Size

15 MB (15,360 KB), which is the size of a file in which trace log data about the execution of approximately 10,000 jobs can be saved

Because an adequate queueless trace log file size differs considerably depending on such factors as whether the job transfers file and error results are output, the trace log file will need to be extended whenever necessary after an adequate file size has been estimated.

For details about how to estimate an appropriate trace log file size, see 7.2.1(2) Estimating the size of the queueless trace log file in the JP1/Automatic Job Management System 3 System Design (Configuration) Guide.

If the queueless trace log file must be extended, use the ajsqltrsetsz command to resize the file. For details about the ajsqltrsetsz command, see ajsqltrsetsz in 4. Commands Used for Special Operation in the manual JP1/Automatic Job Management System 3 Command Reference.

To Page Top

(3) Extending the internal log file for execution of queueless jobs

The initial settings for the internal log file for execution of queueless jobs are as follows:

File name

If the installation folder is the default installation folder or is in a folder protected by the system, the file name is as follows:

%ALLUSERSPROFILE%\Hitachi\JP1\JP1_DEFAULT\JP1AJS2\log\ajsqlexeclog^#1

%ALLUSERSPROFILE%\Hitachi\JP1\JP1_DEFAULT\JP1AJS2\log\ajsqlexeclog_ftpd^#2

The default value for %ALLUSERSPROFILE% is system-drive\ProgramData.

A folder protected by the system is a folder under any of the following:

- system-drive\Windows

- system-drive\Program Files

- system-drive\Program Files (x86)

If the installation folder is other than the above, the file name is as follows:

JP1/AJS3-installation-folder\log\ajsqlexeclog^#1

JP1/AJS3-installation-folder\log\ajsqlexeclog_ftpd^#2

#1:

In a cluster configuration, the file name is as follows:

JP1/AJS3-installation-folder\log\ajsqlexeclog-[logical-host-name]

If the full path name is 256 or more bytes, the maximum length of logical-host-name is 30 bytes.

#2:

This file is created for JP1/AJS3 - Manager only.
Size

The size of the ajsqlexeclog file

24 MB (24,576 KB), which is the size of a file in which the internal execution log data output by the queueless agent service when about 40,000 queueless jobs are executed can be saved

The size of the ajsqlexeclog_ftpd file

10 MB (10,240 KB), which is the size of a file in which the internal execution log data output by the queueless file transfer service when about 20,000 queueless jobs that perform a file transfer are executed can be saved

An adequate size for the internal log file for execution of queueless jobs differs considerably depending on the number of executed queueless jobs, whether the queueless job performs a file transfer, and other factors. Therefore, the trace log file must be extended whenever necessary after an adequate file size has been estimated.

For details about how to estimate an appropriate size for the internal log file for execution of queueless jobs, see 7.2.1(3) Estimating the size of the internal execution logs for queueless jobs in the JP1/Automatic Job Management System 3 System Design (Configuration) Guide.

If the size of the internal execution logs for queueless jobs must be extended, use the ajsqlexecsetsz command to resize the file. For details about the ajsqlexecsetsz command, see ajsqlexecsetsz in 4. Commands Used for Special Operation in the manual JP1/Automatic Job Management System 3 Command Reference.

To Page Top