2.5.20 Perform JP1/VERITAS backup
Function
This service template executes a backup using JP1/VERITAS NetBackup.
This service template assumes that the following servers are being used.
• Backup execution servers
A server running JP1/VERITAS NetBackup (master server).
The backup policy to be executed must already exist.
(1) The backup is executed by JP1/VERITAS NetBackup, and after backup execution finishes, the task finishes.
Prerequisites
For the latest support information about [Required product in the System]/[Prerequisite products in the system executing the service template]/[Prerequisite product OS running in the system executing the service template], see the release notes.
[Required product in the System]
JP1/Automatic Operation 12-00 or later
[Prerequisite products in the system executing the service template]
(1) JP1/VERITAS NetBackup is running
• JP1/VERITAS NetBackup 7.0, 7.1, 7.5, 7.6, 7.7
• JP1/VERITAS NetBackup 8.0, 8.1, 8.2, 8.3
• JP1/VERITAS NetBackup 9.0, 9.1
[Prerequisite product OS running in the system executing the service template]
(1) Windows Server 2008 R2 Standard/Enterprise/Datacenter
(2) Windows Server 2012 Standard/Datacenter, Windows Server 2012 R2 Standard/Datacenter
(3) Windows Server 2016 Standard/Datacenter
(4) Windows Server 2019 Standard/Datacenter
(5) Red Hat Enterprise Linux Server 6 (64-bit x86_64)
(6) Red Hat Enterprise Linux Server 7 (64-bit x86_64)
(7) Red Hat Enterprise Linux Server 8 (64-bit x86_64)
(8) AIX V6
(9) AIX V7
[Usage conditions of prerequisite products in the system executing the service template]
(1) The backup policy to be executed has been set up.
(2) Set the following to define a backup policy with JP1/VERITAS NetBackup.
• Do not set the Start Window of the schedule.
Set up schedule execution with JP1/Automatic Operation.
• Uncheck "Bare Metal Restore". This function is not supported for JP1/VERITAS NetBackup 7.0 or 7.1.
The default with JP1/VERITAS NetBackup 7.0 is for this to be checked, so be sure to confirm this prior to service execution. Other unsupported functions of JP1/VERITAS NetBackup are described in the software documentation for JP1/VERITAS NetBackup. Do not set these functions.
Cautions
(1) To cancel a backup that is being executed, you must cancel the job from the JP1/VERITAS NetBackup side.
Canceling (forced quit) of an executing task on the JP1/Automatic Operation side does not cancel a JP1/VERITAS NetBackup job.
(2) Using the following functions will cause task execution to fail. Do not use these functions.
• Backups that define multiple clients for a single backup policy
• Secondary backups when Disk Staging is used
(3) When the following functions are used, multiple instances of the JP1/VERITAS NetBackup job are executed. The task finishes normally only when all jobs are normal; the task ends abnormally in all other cases.
• Backup using multiple data streams
• Backups using multiple copies
• Catalog backups
Execution privilege
Windows: Administrator permissions
UNIX: root permissions
Version
02.00.00
Tags
Control JP1,VERITAS
Property list
The following shows the list of the property groups set in the property:
|
Property group |
Description |
Initial display |
|---|---|---|
|
Backup execution server environment information |
Specify the environment information for the JP1/VERITAS NetBackup server. |
Y |
|
Backup information |
Specify the policy information to back up. |
Y |
The following shows the list of the properties to be displayed in the "Service Definition" window:
- (Legend)
-
R: The property must be specified.
O: The property can be omitted. However, the property might be mandatory depending on what is specified for other properties. See the Description of each property.
|
Property key |
Property name |
Description |
I/O type |
Shared |
Required |
Property group |
|---|---|---|---|---|---|---|
|
jp1veritas.targetHost |
Host name of the active backup server |
Specifies the host name or IP address of the JP1/VERITAS NetBackup master server. IPv6 addresses are not supported. In the case of a cluster configuration, specify the physical host or logical host of the active server. |
Input |
Disabled |
R |
Backup execution server environment information |
The following shows the list of the properties to be displayed on the "Service Definition" window and the "Submit Service" window:
|
Property key |
Property name |
Description |
I/O type |
Shared |
Required |
Property group |
|---|---|---|---|---|---|---|
|
jp1veritas.jp1nbuPolicyName |
Backup policy name |
Specifies the backup policy name registered in JP1/VERITAS NetBackup. |
Input |
Disabled |
R |
Backup information |
|
jp1veritas.jp1nbuScheduleName |
Schedule name |
Specifies the schedule name defined in the specified backup policy. |
Input |
Disabled |
R |
Backup information |
The following shows the restrictions on inputs to the properties displayed in the "Service Definition" window:
|
Property key |
Characters that can be input |
|---|---|
|
jp1veritas.targetHost |
A maximum of 256 characters can be entered. Characters that can be used include alphanumeric characters, as well as . and -. |
The following shows the restrictions on inputs to the property displayed on the "Service Definition" window and the "Submit Service" window:
|
Property key |
Characters that can be input |
|---|---|
|
jp1veritas.jp1nbuPolicyName |
A maximum of 127 characters can be entered. Characters that can be used include alphanumeric characters, as well as ., -, +, and _, except for leading or trailing . or -. |
|
jp1veritas.jp1nbuScheduleName |
A maximum of 127 characters can be entered. Characters that can be used include alphanumeric characters, as well as ., -, +, and _, except for leading or trailing . or -. |
Flow specification details
The following table shows the detailed specification of the flow:
|
Hierarchy |
Display name |
Plug-in |
||
|---|---|---|---|---|
|
Plug-in name |
Description |
Error recovery method |
||
|
1 |
jp1veritasBackup |
Perform backup (JP1/VERITAS) |
Performs a backup. |
Eliminate the cause of the error, and then re-execute the service. |