2.4.2 Add JP1/Base monitoring setting (repeated flow)
Flow specification details
The following table shows the detailed specification of the flow:
Hierarchy |
Processing |
Plug-in |
||
---|---|---|---|---|
Plug-in name |
Description |
Error recovery method |
||
1 |
checkOS |
OS identification |
Identifies the OS type. |
-- |
1-1 |
Output OS type |
Determines the type of OS. |
Eliminate the cause of the error, and then re-execute the service. |
|
2 |
jp1baseSetup |
JP1/Base setup |
Performs setup of JP1/Base on the specified server. |
-- |
2-3 |
Compatible Plug-in |
Determines whether or not the OS is Windows. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-4 |
Flow Plug-in |
Sets up JP1/Base on a Windows server. |
-- |
|
2-4-3 |
Compatible Plug-in |
Checks that a start sequence definition file has been specified. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-4-4 |
File-forwarding plug-in |
Transfers a start sequence definition file to a monitor server. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-4-5 |
Configure Windows firewall |
Registers the jbssessionmgr process. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-4-6 |
Configure Windows firewall |
Registers the jbsroute process. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-4-7 |
Configure Windows firewall |
Registers the jcocmd process. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-4-8 |
Configure Windows firewall |
Registers the jcocmdapi process. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-4-9 |
Configure Windows firewall |
Registers the jevservice process. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-4-10 |
Configure Windows firewall |
Registers the jbsplugind process. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-4-11 |
Configure Windows firewall |
Registers the jbscomd_snd process. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-4-12 |
Configure Windows firewall |
Registers the jbscomd_rcv process. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-4-15 |
Compatible Plug-in |
Checks that a start sequence definition file has been specified. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-4-16 |
Flow Plug-in |
-- |
-- |
|
2-4-16-3 |
Compatible Plug-in |
Checks that a start sequence definition file has been specified. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-4-16-4 |
Flow Plug-in |
-- |
-- |
|
2-4-16-4-1 |
File-forwarding plug-in |
Transfers a start sequence definition file to a monitor server. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-4-16-4-2 |
JP1/AO Custom Job |
-- |
Eliminate the cause of the error, and then re-execute the service. |
|
2-4-16-4-3 |
Delete file |
Deletes the specified file. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-5 |
Compatible Plug-in |
Determines whether or not the OS is UNIX. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-6 |
Flow Plug-in |
Sets up JP1/Base on a UNIX server. |
-- |
|
2-6-1 |
Copy file |
Copies an auto-start script. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-6-2 |
Copy file |
Copies an auto-stop script. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-6-5 |
Compatible Plug-in |
Checks that a start sequence definition file has been specified. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-6-6 |
Flow Plug-in |
-- |
-- |
|
2-6-6-3 |
Compatible Plug-in |
Checks that a start sequence definition file has been specified. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-6-6-4 |
Flow Plug-in |
-- |
-- |
|
2-6-6-4-1 |
File-forwarding plug-in |
Transfers a start sequence definition file to a monitor server. |
Eliminate the cause of the error, and then re-execute the service. |
|
2-6-6-4-2 |
JP1/AO Custom Job |
-- |
Eliminate the cause of the error, and then re-execute the service. |
|
2-6-6-4-3 |
Delete file |
Deletes the specified file. |
Eliminate the cause of the error, and then re-execute the service. |
|
3 |
jp1baseAddmonitoringConfiguration |
Add JP1/Base monitoring settings |
Adds the JP1/Base monitoring settings. |
Eliminate the cause of the error, and then re-execute the service. |
3-7 |
Compatible Plug-in |
Determines whether or not the OS is Windows. |
Eliminate the cause of the error, and then re-execute the service. |
|
3-8 |
Flow Plug-in |
Transfers a JP1/Base monitoring configuration file to a Windows server. |
-- |
|
3-8-1 |
File-forwarding plug-in |
Transfers a forward file to a monitor server. |
Eliminate the cause of the error, and then re-execute the service. |
|
3-8-2 |
Compatible Plug-in |
Checks whether an event log trap operation definition file has been specified. |
Eliminate the cause of the error, and then re-execute the service. |
|
3-8-3 |
File-forwarding plug-in |
Transfers an ntevent.conf file to a monitor server. |
Eliminate the cause of the error, and then re-execute the service. |
|
3-8-4 |
Compatible Plug-in |
Checks whether a log trap operation definition file has been specified. |
Eliminate the cause of the error, and then re-execute the service. |
|
3-8-5 |
File-forwarding plug-in |
Transfers a jevlog.conf file to a monitor server. |
Eliminate the cause of the error, and then re-execute the service. |
|
3-8-6 |
Compatible Plug-in |
Checks that a log file trap start definition file has been specified. |
Eliminate the cause of the error, and then re-execute the service. |
|
3-8-7 |
File-forwarding plug-in |
Transfers a jevlog_start.conf file to a monitor server. |
Eliminate the cause of the error, and then re-execute the service. |
|
3-8-8 |
Compatible Plug-in |
Checks that a log information definition file has been specified. |
Eliminate the cause of the error, and then re-execute the service. |
|
3-8-9 |
File-forwarding plug-in |
Transfers a jevlogd.conf file to a monitor server. |
Eliminate the cause of the error, and then re-execute the service. |
|
3-9 |
Compatible Plug-in |
Determines whether or not the OS is UNIX. |
Eliminate the cause of the error, and then re-execute the service. |
|
3-10 |
Flow Plug-in |
Transfers a JP1/Base monitoring configuration file to a UNIX server. |
-- |
|
3-10-1 |
File-forwarding plug-in |
Transfers a forward file to a monitor server. |
Eliminate the cause of the error, and then re-execute the service. |
|
3-10-2 |
Compatible Plug-in |
Checks whether a log trap operation definition file has been specified. |
Eliminate the cause of the error, and then re-execute the service. |
|
3-10-3 |
File-forwarding plug-in |
Transfers a jevlog.conf file to a monitor server. |
Eliminate the cause of the error, and then re-execute the service. |
|
3-10-4 |
Compatible Plug-in |
Checks that a log file trap start definition file has been specified. |
Eliminate the cause of the error, and then re-execute the service. |
|
3-10-5 |
File-forwarding plug-in |
Transfers a jevlog_start.conf file to a monitor server. |
Eliminate the cause of the error, and then re-execute the service. |
|
3-10-6 |
Compatible Plug-in |
Checks that a log information definition file has been specified. |
Eliminate the cause of the error, and then re-execute the service. |
|
3-10-7 |
File-forwarding plug-in |
Transfers a jevlogd.conf file to a monitor server. |
Eliminate the cause of the error, and then re-execute the service. |