1.2 コマンド使用時の注意事項
コマンド使用時の注意事項を次に示します。
Windows Serverのホストで,Administrators権限が必要なコマンドを実行する場合は,コマンドプロンプトを管理者として起動する必要があります。Windowsの[スタート]メニューの[コマンドプロンプト]を右クリックし,[管理者として実行]を選択すると,管理者として起動できます。なお,UAC機能が無効の場合,コマンドプロンプトを管理者として起動する必要はありません。
JP1/AOサーバのOSがWindowsの場合,コマンドプロンプトで「簡易編集モード」を有効にして画面上でマウスをクリックすると,簡易編集モードを解除するまで画面出力が停止します。このため,「簡易編集モード」を使用しないことを推奨します。
クラスタ環境でコマンドを使用する場合は,実行系のホストで実行してください。ただし,hcmds64getlogsコマンドは,待機系のホストでも実行できます。
コマンドの実行を中断したい場合は,[Ctrl]+[C]キーを押してください。コマンドの実行を中断した場合は,中断時のメッセージを確認して問題が発生していないか確認してください。再実行したい場合は,再度コマンドを実行してください。
コマンドの実行中に[Ctrl]+[S]キーを押さないでください。[Ctrl]+[S]キーを押すと,コマンドの出力が停止します。
stoptaskコマンドおよびsubmittaskコマンド以外のコマンドは,JP1/AOのほかのコマンドと同時に実行できません。
コマンドの種類によっては,コマンドを実行した直後に割り込み操作をした場合,「2(コマンドの実行を中断しました)」以外の戻り値が返るときがあります。
stoptaskコマンド,submittaskコマンドはそれぞれ同時に10個まで実行できます。それを超えて実行した場合,次のメッセージが表示されタスクは実行されません。
KNAE03236-Eコマンドの同時実行数を超えました。実行中のコマンドの終了を待って,再実行してください。
次のコマンドを実行する場合,ユーザー設定プロパティファイルの設定を変更することで,監査ログに出力されるサブジェクト識別情報を変更できます。
deleteremoteconnectionコマンド
deleteservicetemplateコマンド
importservicetemplateコマンド
listremoteconnectionsコマンド
listservicesコマンド
listtasksコマンド
setremoteconnectionコマンド
stoptaskコマンド
submittaskコマンド
JP1/AOサーバのOSがLinuxの場合,標準設定でコアファイル出力時の最大サイズが「0」になっていると,コアダンプは出力されません。障害時にコアダンプを出力するには,ulimitコマンドを実行して,各コマンドを実行する前に最大サイズを無制限(unlimited)に設定してください。
JP1/AOサーバのOSがWindowsの場合,指定したファイルパスの大文字・小文字は区別されません。JP1/AOサーバのOSがLinuxの場合,指定したファイルパスの大文字・小文字は区別されます。