ftsregc - registers, changes, deletes, and displays transmission information
- Organization of this page
Format
- Registering:
ftsregc /N [transmission-card-name] [transmission-information-option transmission-option-parameter]
- Changing:
ftsregc /C transmission-card-name [transmission-information-option transmission-option-parameter]
- Deleting:
ftsregc /D transmission-card-name
- Displaying:
ftsregc /L transmission-card-name
Function
The ftsregc command registers, changes, deletes, or displays transmission information.
Arguments
/N [transmission-card-name] [transmission-information-option transmission-option-parameter]
There are two ways to register transmission information. One is by registering new transmission information that has been set on a transmission card. The other is by using an existing transmission card as a model and editing its contents in order to register it as a separate transmission card.
-
Registering new transmission information onto a transmission card
ftsregc /N [transmission-information-option transmission-option-parameter]
This method creates new transmission information based on the information specified with the transmission information options. Among the available transmission information options, you must always specify /TC, /TH, /TU, /TT, /TY, /TL, and /TR. You must use the /TC transmission information option to specify a name for the transmission card.
-
Registering transmission information using an existing transmission card
ftsregc /N [transmission-card-name] [transmission-information-option transmission-option-parameter]
This method specifies the name of a transmission card to use as a model and then specifies transmission information options to change. You must specify in /TC a name for the new transmission card that you are registering.
The table below lists and describes the transmission information options.
Option name |
Transmission option parameter |
Value |
---|---|---|
/TC |
Card name |
((1 to 20 bytes)) |
/TH |
Connection-target host name |
((1 to 256 bytes)) |
/TP |
Connection-target port number |
((1 to 65,535)) |
/TU |
Login user name |
((1 to 50 bytes)) |
/TW |
Login password |
((1 to 50 bytes)) |
/TT |
Send/receive type:
|
SEND|RECV|APPE |
/TY |
Transmission mode:
|
ASCII|BINARY |
/TM |
Compression mode:
|
STREAM|COMPRESS |
/TK |
Size check:
|
CHECK|UNCHECK |
/TL |
Local file name |
((1 to 259 bytes)) |
/TR |
Remote file name |
((1 to 259 bytes)) |
/TS |
Name of the program to start when transmission ends normally |
((1 to 259 bytes)) |
/TF |
Name of the program to start when transmission ends abnormally |
((1 to 256 bytes)) |
/TX |
FTP command |
((1 to 300 bytes)) |
/TO |
Comment |
((1 to 80 bytes)) |
/TA |
Single-file or multiple-file transmission during reception:
|
AUTO|MULTIPLE|SINGLE |
For details about each transmission option parameter, see 3.4.1 Registering transmission information onto a transmission card.
/C card-name [transmission-information-option transmission-option-parameter]
Changes from the specified card the transmission information that is specified by the transmission information options.
/D card-name
Deletes the transmission information identified by the specified card name.
/L card-name
Displays the transmission information for the specified card.
Return values
0 |
Normal termination |
6100001 |
Omission of card name specification during registration |
6100002 |
Omission of remote host name specification during registration |
6100003 |
Omission of login user name specification during registration |
6100004 |
Omission of send/receive type specification during registration |
6100005 |
Omission of transmission mode specification during registration |
6100006 |
Omission of local file name specification during registration |
6100007 |
Omission of remote file name specification during registration |
6100008 |
Abnormal termination when an existing card name is specified |
6100009 |
Omission of card name specification during registration |
6100010 |
Abnormal termination during registration of card information |
6200001 |
Omission of card name specification during change |
6200002 |
Abnormal termination during acquisition of card information before change |
6200003 |
Abnormal termination during acquisition of card information after change |
6200004 |
Abnormal termination during deletion of card information before change |
6200005 |
Abnormal termination during change of card information |
6300000 |
Abnormal termination when ftsregc /D is specified |
6400000 |
Abnormal termination when ftsregc /L is specified |
6900000 |
Command line syntax error |
9000001 |
Abnormal termination common to ftsregc |
9900001 |
Abnormal termination (not executed by the administrator) |
For details about the messages that are displayed, see 8.3.2 Messages displayed during execution of the ftsregc command.