10.4.5 Access log area (Log data tab selected)

Organization of this subsection

(1) Window configuration
(2) Window description
(3) Supplemental notes

(1) Window configuration

[Figure]

(2) Window description

This window displays a tabular list of access logs for a monitored target within a monitored service.

No.	Item	Description
1	`X` - All Web Access	This area displays the name of the service group whose performance charts are to be viewed. `X` is the name of a service group.
2	Access log list	This area displays a tabular list of access logs over the range indicated by the solid lines in the performance charts. The access logs displayed in the Access log area show data acquired up to five minutes before the current time. The items to display are selected in the Select items to be displayed window.
3	Logging range	This area displays the interval being displayed in the Log data tab using the following format. Display format `YYYY/MM/DD` `hh:mm:ss` `-` `YYYY/MM/DD` `hh:mm:ss`
4	Showing/Total	This area displays the number of access logs. Showing (`nnnn`) The number of access logs being displayed in the Log data tab Total (`mmmm`) The number of access logs in the range indicated by the solid lines in the performance charts Display format `nnnn/mmmm`
5	Display Settings button	Clicking this button displays the Select items to be displayed window.
6	Display button	Clicking this button displays the Confirmation of the display of the access log window.

Logging range of the access logs

In the performance charts, dotted lines indicate the range targeted for display in the Access log area. Solid lines indicate the range actually being displayed in the Access log area.

Figure 10‒2: Logging range in the Access log area

No.	Item	Description
1	Logging range (solid lines)	The range of access logs actually being displayed in the Access log area.
2	Logging range (dotted lines)	The range of access logs targeted for display in the Access log area.

The dotted lines are shown when the display interval in the Performance chart tab is 30 minutes or longer.

You can change the logging range of the access logs by clicking and dragging the performance chart.

Figure 10‒3: Changing the logging range in the Access log area

Interval of the logging range (dotted lines)

The logging range indicated by the dotted lines in the Access log area changes depending on the display interval of the performance chart.

No.	Display interval in the Performance chart tab	Display interval in the Access log area	Logging range displayed between the dotted lines
1	1 minute	1 minute	The range of access logs shown in the Performance chart tab when you click the Display button.
2	10 minutes	10 minutes
3	30 minutes	10 minutes	The range of access logs indicated by the dotted lines in the Performance chart tab when you click the Display button.
4	1 hour	10 minutes
5	6 hours	10 minutes
6	1 day	10 minutes

Number of access logs displayed

A maximum of 5,000 access logs can be displayed in the Access log area. If the number of access logs in the logging range indicated by dotted lines exceeds this maximum, an error message is shown and only the maximum number of access logs are displayed, ordered by response time.

Sorting access logs

When a column header on the Log data tab is clicked, the access logs are sorted according to the item corresponding to that column header. Note that the sorting behavior changes if you click the column header while pressing the Ctrl key on the keyboard. For details, see the table below.

[Figure]

Column status	Sorting behavior
Not sorted	You can use the following two methods to sort the access logs: Click the column header corresponding to the item by which access logs are to be sorted. Access logs are sorted by the applicable item in ascending order. If sorting by another item was already applied, that sorting is cleared. Click on the column header corresponding to the item by which access logs are to be sorted while pressing the Ctrl key on the keyboard. Access logs are sorted by the applicable item in ascending order. If sorting by another item was already applied, the access logs will be sorted by both the previously selected item and the newly selected item.
Sorted	You can use the following two methods to sort the access logs: Click the column header corresponding to the item by which access logs are to be sorted. Access logs are sorted by the applicable item in reverse order. However, if sorting by another item was already applied, that sorting is cleared and the access logs are sorted by the newly selected item in reverse order. Click on the column header corresponding to the item by which access logs are to be sorted while pressing the Ctrl key on the keyboard. Access logs are sorted by the applicable item in reverse order.

Column status

Sorting behavior

Not sorted

You can use the following two methods to sort the access logs:

Click the column header corresponding to the item by which access logs are to be sorted.

Access logs are sorted by the applicable item in ascending order.

If sorting by another item was already applied, that sorting is cleared.

Click on the column header corresponding to the item by which access logs are to be sorted while pressing the Ctrl key on the keyboard.

Access logs are sorted by the applicable item in ascending order.

If sorting by another item was already applied, the access logs will be sorted by both the previously selected item and the newly selected item.

Sorted

You can use the following two methods to sort the access logs:

Click the column header corresponding to the item by which access logs are to be sorted.

Access logs are sorted by the applicable item in reverse order.

However, if sorting by another item was already applied, that sorting is cleared and the access logs are sorted by the newly selected item in reverse order.

Click on the column header corresponding to the item by which access logs are to be sorted while pressing the Ctrl key on the keyboard.

Access logs are sorted by the applicable item in reverse order.

To Page Top

(3) Supplemental notes

To record access logs, you must set the folder where the logs are to be recorded as a property in SLM - UR's system definition file (jp1itslmur.properties).

For details, see 5.6 Editing the system definition files to change settings.
The following actions re-initialize the Access log area so that no access logs are displayed:
- Displaying a different service or transaction in the Services area
- Displaying the Troubleshoot window by clicking the Details column in the Event tab
- Displaying the Troubleshoot window by clicking the Troubleshoot button in the Real-time Monitor window
The access logs are retained for a period of 194 hours (8 days x 24 hours + 2 hours in output). Access logs that exceed this maximum display period are deleted.

To Page Top