1.5.1 Setting up SLM - Manager
- Organization of this subsection
(1) Before you start
Verify that your user account belongs to the OS's Administrators group.
Before you start the setup, install the SLM - Manager that is to be set up.
For details about the installation, see 1.4.1 Installing SLM.
Verify that JP1/Base has been installed on the host on which SLM - Manager is being installed.
For details about how to install JP1/Base, see the JP1/Base User's Guide.
(2) Procedure
To set up SLM - Manager:
Create the options file required for setup.
For details about the options file, see A.4 jslmmgrsetup (sets up SLM - Manager) in A. Commands.
Store the created options file in a desired folder.
Make sure that the absolute path of the options file storage location does not exceed 255 bytes including the options file name (any name).
Execute the setup command.
The following shows the setup command that is to be executed:
SLM-Manager-installation-folder\mgr\bin\jslmmgrsetup absolute-path-of-options-file
For details about the setup command, see A.4 jslmmgrsetup (sets up SLM - Manager) in A. Commands.
When the command terminates normally, SLM - Manager setup is complete.
When setup finishes, the default startup method of each service is initially set as follows:
Service |
Service name |
Default startup method |
---|---|---|
SLM - Manager DB Service |
HiRDBEmbeddedEdition_JL0 |
Automatic |
SLM - Manager DB Cluster Service |
HiRDBClusterService_JL0 |
Manual |
SLM - Manager Service |
JP1_ITSLM_MGR_Service |
Manual |
SLM - Manager Web Service |
JP1_ITSLM_MGR_Web_Service |
Manual |
Be careful if you have already set up SLM - Manager and have changed the default startup methods of services. In this case, if you perform unsetup of SLM - Manager and then set it up again, the default startup methods of the services are reset to the initial settings.
(3) Supplementary information
If a firewall has been set up on the host on which SLM - Manager has been set up, you must release the port numbers that were specified for the psb_Listen and manager_port definition items in the options file used during setup. If you change the settings in the options file, you must also change the firewall settings, and then check the following:
Check if ephemeral ports for communication between SLM - Manager and SLM - UR and between SLM - Manager and the browser have been released.
If they have not been released, set up the firewall to release ephemeral ports or set it up to allow communication from the following programs:
- SLM - Manager-installation-folder\mgr\bin\system\jslmmUR.exe
- SLM - Manager-installation-folder\mgr\bin\system\jslmmRMI.exe
- SLM - Manager-installation-folder\mgr\system\psb\CC\web\bin\cjstartweb.exe
Check if the firewall is allowed to communicate with the loopback address of the host where SLM - Manager is set up.
To adjust the time on the host on which SLM - Manager has been set up, you must first terminate all SLM - Managers and SLM - URs. To do this, first stop all services running on the SLM - Managers and SLM - URs.
It is preferable to adjust SLM - Manager's time forward. If SLM - Manager's time is set earlier as a result of adjustment (adjusted backward), wait until the amount of time that was adjusted backward has elapsed, and then start SLM - Manager and SLM - UR. For example, if you moved the computer's time backward by five minutes, wait for at least five minutes before you start SLM - Manager.
Note that you can adjust the time of a computer that displays windows used for monitoring at any time, regardless of whether SLM - Manager is running.
Make sure that you specify a value in the range from 1 to 65535 for the psb_Listen definition item in the options file that is used when the jslmmgrsetup command is executed. If you have specified any other value and then performed the setup, perform setup again using the procedure described below after a setup error has been issued.
Correct the Listen property value defined in the file shown below (httpsd.conf) to a value in the range from 1 to 65535:
SLM-Manager-installation-folder\mgr\system\psb\httpsd\conf\httpsd.conf
Specify a value in the range from 1 to 65535 for the psb_Listen definition item in the jslmmgrsetup command's options file, and then perform setup again.