15.5.1 Setting up the JP1/AJS3 definition pre-check function

As a protection against failures during live operation, JP1/AJS3 can check for problems in the definition of a job before live operation of the job starts. This subsection describes how to set up this function.

Organization of this subsection

(1) Procedure for setting up the function
(2) Procedure for changing the function settings
(3) Environment setting parameters

(1) Procedure for setting up the function

To set up the JP1/AJS3 definition pre-check function:

Execute the following command:

For JP1/AJS3 - Manager:
```
  #/opt/jp1ajs2/bin/ajschksetup -m -a
```
For JP1/AJS3 - Agent:
```
  #/opt/jp1ajs2/bin/ajschksetup -a
```
For details about the ajschksetup command, see ajschksetup in 2. Commands Used during Setup in the manual Job Management Partner 1/Automatic Job Management System 3 Command Reference 2.
Start the JP1/AJS3 Check Manager service and the JP1/AJS3 Check Agent service.

The following shows the commands to be executed.

For JP1/AJS3 - Manager:
```
  #/opt/jp1ajs2/bin/ajschkstart -m -a
```
For JP1/AJS3 - Agent:
```
  #/opt/jp1ajs2/bin/ajschkstart -a
```
For details about the ajschkstart command, see ajschkstart (UNIX only) in 2. Commands in the manual Job Management Partner 1/Automatic Job Management System 3 Command Reference 1.

To Page Top

(2) Procedure for changing the function settings

To change the settings of the JP1/AJS3 definition pre-check function:

Stop the JP1/AJS3 Check Manager service and the JP1/AJS3 Check Agent service.

The following shows the commands to be executed.

For JP1/AJS3 - Manager:
```
  #/opt/jp1ajs2/bin/ajschkstop -m -a
```
For JP1/AJS3 - Agent:
```
  #/opt/jp1ajs2/bin/ajschkstop -a
```
For details about the ajschkstop command, see ajschkstop (UNIX only) in 2. Commands in the manual Job Management Partner 1/Automatic Job Management System 3 Command Reference 1.

Execute the following command to set the environment setting parameters described in (3) below:

jajs_config -k definition-key "parameter-name-1"=value-1 
["parameter-name-2"=value-2] 
["parameter-name-3"=value-3] 
["parameter-name-4"=value-4] 
["parameter-name-5"=value-5]

Start the services that you stopped in step 1.

The following shows the commands to be executed.

For JP1/AJS3 - Manager:
```
  #/opt/jp1ajs2/bin/ajschkstart -m -a
```
For JP1/AJS3 - Agent:
```
  #/opt/jp1ajs2/bin/ajschkstart -a
```
The new settings are applied.

To Page Top

(3) Environment setting parameters

Table 15‒59: Environment setting parameters used to specify the settings of the JP1/AJS3 definition pre-check function
No.	Definition key	Environment setting parameter	Explanation
1	`[JP1_DEFAULT\JP1AJS2\CHECK]`	`"AJSCHK_CHECKFILE"`^#`=`	Specifies the name of the file where the definition pre-check results will be stored.
2		`"AJSCHK_LOGDIR"=`	Specifies the name of the definition check log directory.
3		`"AJSCHK_LOGSIZE"=`	Specifies the size of the definition check log files.
4		`"AJSCHK_TRACELOGFILE"=`	Specifies the name of the trace log file for the definition pre-check function.
5		`"AJSCHK_CHARCODE"=`	Specifies the character encoding used to display job information and the definition pre-check results.

#:: This parameter can be set only in JP1/AJS3 - Manager.

For details about the definition of these environment setting parameters, see the following:

2.5.2(1) AJSCHK_CHECKFILE in the Job Management Partner 1/Automatic Job Management System 3 Configuration Guide 2
2.5.2(2) AJSCHK_LOGDIR in the Job Management Partner 1/Automatic Job Management System 3 Configuration Guide 2
2.5.2(3) AJSCHK_LOGSIZE in the Job Management Partner 1/Automatic Job Management System 3 Configuration Guide 2
2.5.2(4) AJSCHK_TRACELOGFILE in the Job Management Partner 1/Automatic Job Management System 3 Configuration Guide 2
2.5.2(5) AJSCHK_CHARCODE in the Job Management Partner 1/Automatic Job Management System 3 Configuration Guide 2

To Page Top