2.1 Messages
This section explains the causes and corrective actions for the messages from KDCZ00000 to KDCZ09999.
-
KDCZ00101-E
A node name setting is incorrect. You cannot use control characters (such as tabs) in node names.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00102-E
A display string setting is incorrect. You cannot use control characters other than line feeds (such as tabs) in display strings.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x09, 0x0B, 0x0C, 0x0E to 0x1F, and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00103-E
A string color setting is incorrect. You can use only one-byte alphanumeric characters and hash marks (#).
- Cause
-
The setting that was entered is invalid. The possible causes are as follows:
-
The setting contains a character that is not permitted (a character other than single-byte alphanumeric characters and the hash mark (#)).
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00104-E
A URL setting is incorrect. You cannot use control characters (such as tabs) in URLs.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00105-E
A tooltip setting is incorrect. You cannot use control characters (such as tabs) in tooltips.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00106-E
A setting for the maximum number of characters allowed is incorrect. Set the maximum number of characters allowed in the range of 1 to 65,535.
- Cause
-
The setting that was entered is invalid. The possible causes are as follows:
-
The setting is missing.
-
A value outside the range from 1 to 65535 was entered.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00107-E
A display string setting is incorrect. You cannot use control characters (such as tabs) in display strings.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00108-E
A value setting is incorrect. You cannot use control characters (such as tabs) in values.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00109-E
A group name setting is incorrect. You cannot use control characters (such as tabs) in group names.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00110-E
An anchor string setting is incorrect. You cannot use control characters (such as tabs) in anchor strings.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00111-E
A URL setting is incorrect. You cannot use control characters (such as tabs) in URLs.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00112-E
A tooltip setting is incorrect. You cannot use control characters (such as tabs) in tooltips.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00114-E
No more parts can be placed. (maximum number of parts = maximum-number-of-parts-that-can-be-placed-in-the-area)
- Cause
-
There are too many parts for the Operational Flow area or the Guide area in the Operational Content Editing window.
- Action
-
Delete unneeded parts.
-
KDCZ00116-E
The list data for the Operational Content that you obtained is incorrect.
- Cause
-
The acquired operational content list data is NULL.
- Action
-
Contact your customer support center.
-
KDCZ00117-E
The menu data that you obtained is incorrect.
- Cause
-
The acquired data for the menu area is NULL.
- Action
-
Contact your customer support center.
-
KDCZ00118-Q
Do you want to discard the information you are entering?
- Cause
-
An operation that suspended processing was performed while items were being processed in the Operational Content Execution window.
-
KDCZ00119-Q
An Operational Content was not saved. Do you want to discard this Operational Content?
- Cause
-
An operational content is being edited currently in the Operational Content Editing window.
- Action
-
To save the operational content that is being edited, click the Cancel button, and then save the operational content. If there is no need to save the operational content, click the OK button.
-
KDCZ00122-I
The Operational Content ID was copied to the clipboard. (Operational Content ID = the-first-Operational-Content-ID ... total-number-of-copied-Operational-Content ID in total)
- Cause
-
The operational content IDs in the selected flow were copied to the clipboard.
-
KDCZ00124-Q
You cannot omit the Operational Content name. Do you want to enter it again?
- Cause
-
The setting that was entered is invalid. The possible causes are as follows:
-
No name was entered for the operational content.
-
The name for the operational content consists of only double-byte or single-byte spaces.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00125-E
The Operational Content name exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters bytes)
- Cause
-
The setting that was entered exceeds the maximum number of characters (the maximum number of characters output by arguments).
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00128-E
An Operational Content name is incorrect. You cannot use control characters (such as tabs) in the name.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00129-Q
The selected Operational Content will be deleted. Do you want to continue?
- Cause
-
You have requested deletion of an operational content in the Operational Content Editing window.
- Action
-
If you want to delete the selected operational content, click the OK button. Otherwise, click the Cancel button.
-
KDCZ00132-I
The Operational Content was saved.
- Cause
-
The operational content has been saved.
-
KDCZ00133-E
The Operational Content ID could not be copied to the clipboard.
- Cause
-
An attempt to copy operational content IDs to the clipboard failed when operational content IDs were to be acquired.
- Action
-
Try again. If the problem persists, contact your customer support center.
-
KDCZ00135-E
An ID setting is incorrect. You cannot use control characters (such as tabs) in IDs.
- Cause
-
The setting entered in the ID text box in the Edit Access Permission Groups window is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00136-E
You cannot omit the ID.
- Cause
-
The setting that was entered is invalid. The possible causes are as follows:
-
The setting consists of only an empty character string.
-
The setting consists of only double-byte or single-byte spaces.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00137-E
A maximum of 64 users and groups can be set for one access rights group.
- Cause
-
More than 64 users or groups were set for one access permission group.
- Action
-
Delete excess users or groups.
-
KDCZ00138-E
An access rights group setting is incorrect. You cannot use control characters (such as tabs) in the name.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00139-E
You cannot omit the name of the access rights group.
- Cause
-
The setting that was entered is invalid. The possible causes are as follows:
-
The setting consists of only an empty character string.
-
The setting consists of only single-byte spaces.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00140-E
You cannot omit the user or group setting.
- Cause
-
No user or group is defined for specifying access permissions.
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00141-Q
The selected access rights group will be deleted. Do you want to continue?
- Cause
-
Deletion of an access permission group was requested in the Access Permissions window.
- Action
-
If you want to delete the selected access permission group, click the OK button. Otherwise, click the Cancel button.
-
KDCZ00142-Q
Some access rights groups have not been saved. Do you want to discard these access rights groups?
- Cause
-
An access permission group is currently being edited in the Access Permissions window.
- Action
-
To save the access permission group that is being edited, click the Cancel button, and then save the access permission group. If there is no need to save the access permission group, click the OK button.
-
KDCZ00144-E
The same values are set within a group. Set different values.
- Cause
-
The value for the radio button specified in Value in the Attribute Settings window has already been set for a radio button in the same group.
- Action
-
Specify a unique value in the same group.
-
KDCZ00146-W
To close the window, click the [Logout] button, and then exit.
- Cause
-
Either of the following are cases possible:
-
An attempt was made to close the page while the Operational Content Execution window or the Operational Content Editing window was displayed.
-
An attempt was made to move to another page while the Operational Content Execution window or the Operational Content Editing window was displayed.
-
- Action
-
Click the Cancel button in the dialog box.
If you want to end the task, click the Close button or the Logout button, and then end the task.
- Supplementary information
-
You can change the contents of this message by specifying the user message properties file (ucnp_message_user.properties). For details, see the Hitachi Navigation Platform Setup and Operations Guide.
-
KDCZ00147-E
A node name exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters bytes)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting is greater than 128 bytes in UTF-8.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00148-E
A display string exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting exceeds the maximum number of characters.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00149-E
A string color exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters bytes)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting is greater than 128 bytes in UTF-8.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00150-E
A URL exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters bytes)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting is greater than 1,024 bytes in UTF-8.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00151-E
A tooltip exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters bytes)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting is greater than 128 bytes in UTF-8.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00152-E
A display string exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters bytes)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting is greater than 1,024 bytes in UTF-8.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00153-E
A value exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters bytes)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting is greater than 128 bytes in UTF-8.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00154-E
A group name exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters bytes)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting is greater than 128 bytes in UTF-8.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00155-E
An anchor string exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters bytes)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting is greater than 1,024 bytes in UTF-8.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00156-E
A URL exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters bytes)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting is greater than 1,024 bytes in UTF-8.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00157-E
A tooltip exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters bytes)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting is greater than 128 bytes in UTF-8.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00158-E
You cannot omit this value.
- Cause
-
The setting that was entered is invalid. The possible causes are as follows:
-
No value was entered for the radio button.
-
The value specified for the radio button consists of only double-byte or single-byte spaces.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00159-E
You cannot omit the maximum number of characters allowed.
- Cause
-
The setting that was entered is invalid. The possible causes are as follows:
-
No entry was made for the permitted maximum number of characters.
-
Only double-byte or single-byte spaces were entered for the permitted maximum number of characters.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00160-E
You cannot omit the anchor string.
- Cause
-
The setting that was entered is invalid. The possible causes are as follows:
-
No anchor character string was entered.
-
Only double-byte or single-byte spaces were entered as the anchor character string.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00161-E
An ID exceeding the maximum number of characters allowed is specified. (maximum number of characters = maximum-number-of-characters bytes)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting is greater than 254 bytes in UTF-8.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00162-E
An access rights group name exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters bytes)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting is greater than 255 bytes in UTF-8.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00163-E
An initial value setting is incorrect. You must set the number of characters of the initial value to a value less than the maximum number of characters you have specified.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting exceeds the permitted maximum number of characters.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00164-E
An initial value setting is incorrect. You cannot use control characters (such as tabs) in initial values.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00165-E
A character size setting is incorrect. Set the character size in the range from 1 to value-of-the-ucnp.base.client.label.font.maxsize-property.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting is outside the range from 1 to 128.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00166-W
Some connectors could not be copied. The selections of these connectors will be canceled. When you copy connectors, you must also select the source/destination parts to connect.
- Cause
-
When the Copy button was clicked on the toolbar in the Operational Content Editing window, there was a connector (linked line) that could not be copied.
- Action
-
If you want to copy the connector (linked line) that could not be copied, also select the connection source and target part at the same time, and then click the Copy button. To copy multiple parts and connectors (linked lines), hold down the Shift key, select the corresponding parts, and then click the Copy button.
-
KDCZ00167-E
You are trying to paste more than the allowed number of parts. (target area = target-area (operation-flow-or-guide), number of current parts = number-of-current-parts, number of parts you tried to paste = number-of-parts-you-tried-to-paste, maximum number of parts = 100)
- Cause
-
An attempt was made to paste too many parts.
- Action
-
Delete unneeded parts or reduce the number of parts to be copied, and then paste the parts.
-
KDCZ00168-E
An initial value setting is incorrect. You cannot use control characters, except for line feeds (such as tabs), in initial values.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x09, 0x0B, 0x0C, 0x0E to 0x1F, and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00169-E
A display string setting is incorrect. You cannot use control characters (such as tabs) in display strings.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00170-E
A display string exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters bytes)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting is greater than 1,024 bytes in UTF-8.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00171-E
A node ID setting is incorrect. You can use only one-byte alphanumeric characters, hyphens (-), and underscores (_).
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
Characters other than single-byte alphanumeric characters, single-byte hyphens (-), and single-byte underscores (_) were used.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00172-E
A node ID has the same ID as another node in the Operational Flow. Set a different node ID. (name of the node with the same node ID = name-of-the-node-with-the-same-node-ID)
- Cause
-
The operational flow contains a node with a duplicated node ID.
- Action
-
Specify node IDs that are unique within the same operational flow.
-
KDCZ00173-E
A URL setting is incorrect. You cannot use control characters (such as tabs) in URLs.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00174-E
A URL exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters bytes)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting is greater than 1,024 bytes in UTF-8.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00175-E
An initial value exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting exceeds the maximum number of characters.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00177-I
The entered information was saved.
- Cause
-
The entered information has been saved.
-
KDCZ00178-Q
The information you are entering will be discarded. Click [OK] to continue.
If you want to save the entered information and resume operations at a later time, click [Cancel], and then click the [Save temporarily] button.
- Cause
-
An operation that exits the current window, such as a log-out operation, was performed in the Operational Content Execution window without first saving the information that had been entered.
- Action
-
If you want to discard the information that was entered, click the OK button. If you want to save the information that was entered and then suspend the operation, click the Cancel button, and then click the Suspend button.
-
KDCZ00179-Q
The entered information was saved. Do you want to restore?
- Cause
-
The selected operational content includes the saved information that was being entered.
- Action
-
To restore the information that was being entered, click the OK button. To start over without restoring the information, click the Cancel button.
-
KDCZ00180-E
The Operational Contents were updated after the entered information was saved. The saved information cannot be restored, and the operation will be started from the beginning.
- Cause
-
The operational content was updated by an import operation after the information that was being entered had been saved.
- Action
-
Take the following corrective action:
-
User
Contact the system administrator.
-
System administrator
Determine whether the suspend information about the operational content that was updated during the import operation has been deleted.
-
-
KDCZ00181-E
Failed to restore the entered information.
- Cause
-
An error occurred during Suspend/Resume Plugin processing.
- Action
-
Take the following corrective action:
-
User
Contact the system administrator.
-
System administrator
The problem described below has occurred. Contact the user who developed the plugin, and then take the appropriate corrective action.
The Suspend/Resume Plugin returned true by the contains method, but the load method returned null. If the contains method has returned true, make sure that the suspended information is returned or an exception is thrown.
-
-
KDCZ00182-E
A parent Guide Part ID setting is incorrect. You can use only one-byte alphanumeric characters, hyphens (-), and underscores (_).
- Cause
-
The value that was entered is invalid. The possible cause is as follows:
-
Characters other than single-byte alphanumeric characters, single-byte hyphens (-), and single-byte underscores (_) were used.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00183-E
The ID that you specified as the parent Guide Part ID does not exist within the same guide area.
- Cause
-
The drop-down part with the specified guide part ID does not exist in the same Guide area.
- Action
-
Specify the guide part ID of a drop-down part that exists in the same Guide area.
-
KDCZ00184-E
A setting of the value for parent number position-counted-from-the-top-of-the-list-in-the-Attribute-Settings-window is incorrect. You cannot use control characters (such as tabs).
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00185-E
The value of parent number position-counted-from-the-top-of-the-list-in-the-Attribute-Settings-window overlaps with the value for another parent. The parent value set must be unique within the same drop-down parts. (overlapping value = overlapping-value-of-parent)
- Cause
-
The parent's value is duplicated.
location in the message displays the first two duplicate parent values, separated by a comma.
- Action
-
Change or delete duplicated parent values so that all parent values are unique within the same part.
-
KDCZ00186-E
A setting of the-label-or-value-of-the-selected-item for number position-counted-from-the-top-of-the-list-in-the-Attribute-Settings-window is incorrect. You cannot use control characters (such as tabs). (value of parent = value-of-parent)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00187-E
The format of the-label-or-value-of-the-selected-item for number position-counted-from-the-top-of-the-list-in-the-Attribute-Settings-window is incorrect. If you want to use quotation marks (") in an element name, specify two quotations successively as escape characters, and then enclose the element itself with quotations. (value of parent = value-of-parent)
- Cause
-
There is an error in the format.
- Action
-
If an element name contains a double quotation mark ("), specify it as two consecutive double quotation marks, and then enclose the entire element name in double quotation marks.
-
KDCZ00188-E
The format of the-label-or-value-of-the-selected-item for number position-counted-from-the-top-of-the-list-in-the-Attribute-Settings-window is incorrect. If you specify a quotation at the beginning of an element name, you must also specify a quotation at the end. (value of parent = value-of-parent)
- Cause
-
A double quotation mark (") is specified only at the beginning of the element name.
- Action
-
Check the label or value of the selected item indicated in the message, and then add a double quotation mark (") at the end of the element name.
-
KDCZ00189-E
The number of elements in the-label-of-the-selected-item for number position-counted-from-the-top-of-the-list-in-the-Attribute-Settings-window exceeds the maximum. (value of parent = value-of-parent, specified number of elements = specified-number-of-elements, maximum number of elements = maximum-number-of-elements)
- Cause
-
The number of label elements for the selected item exceeds the maximum.
- Action
-
Delete elements so that the number of elements does not exceed the maximum.
-
KDCZ00190-E
The number of elements differ between the-label-of-the-selected-item for number position-counted-from-the-top-of-the-list-in-the-Attribute-Settings-window and the-value-of-the-selected-item for number position-counted-from-the-top-of-the-list-in-the-Attribute-Settings-window. The numbers of elements must be consistent. (value of parent = value-of-parent, number of elements of the-label-of-the-selected-item = number-of-elements-of-the-name-of-the-selected-item, number of elements of the-value-of-the-selected-item = number-of-elements-of-the-value-of-the-selected-item)
- Cause
-
The number of label elements does not match the number of value elements for the selected item.
- Action
-
Revise the settings so that the number of label elements matches the number of value elements for the selected item.
-
KDCZ00191-E
The number of characters in the-label-or-value-of-the-selected-item for number position-counted-from-the-top-of-the-list-in-the-Attribute-Settings-window exceeds the maximum. (value of parent = value-of-parent, index of element = index-of-element-where-an-error-occurred, number of characters of element = number-of-characters-of-element-where-an-error-occurred, maximum number of characters = maximum-number-of-characters)
- Cause
-
There is an element whose length exceeds the maximum number of characters.
Note that the index for the leftmost element is 0. If there are multiple elements, indexes are assigned sequentially as integers in the order the elements are specified.
- Action
-
Revise the settings so that the element's length does not exceed the maximum number of characters.
-
KDCZ00192-E
You cannot modify the Guide Part ID of a part that is already referenced by another part. Cancel the reference, and then modify the ID. (referenced Guide Part ID = referenced-Guide-Part-ID)
- Cause
-
An attempt was made to change a guide part ID, but the corresponding part was referenced by another part.
source-guide-part-IDs-list in the message displays the guide part IDs separated by a comma.
- Action
-
Cancel the reference relationship, and then perform the operation again.
-
KDCZ00193-E
A Guide Part ID setting is incorrect. You can use only one-byte alphanumeric characters, hyphens (-), and underscores (_).
- Cause
-
The value that was entered is invalid. The possible cause is as follows:
-
Characters other than single-byte alphanumeric characters, single-byte hyphens (-), and single-byte underscores (_) were used.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00194-E
The specified Guide Part ID has already been used for another Guide Part. The Guide Part ID set must be unique within the same guide area. (overlapping Guide Part ID = overlapping-Guide-Part-ID)
- Cause
-
There is a guide part with a duplicate guide part ID in the Guide area.
- Action
-
Revise the settings so that all guide part IDs are unique within the Guide area.
-
KDCZ00195-E
The value of the element in the-value-of-the-selected-item for number position-counted-from-the-top-of-the-list-in-the-Attribute-Settings-window is overlapping. The value set must be unique within the same text box. (value of parent = value-of-parent, index of the overlapping element = index-of-the-overlapping-element, overlapping value = overlapping-value)
- Cause
-
Element values for the selected item are duplicated.
Note that the index for the leftmost element is 0. If there are multiple elements, indexes are assigned sequentially as integers in the order the elements are specified. For duplicate-elements-indexes, the first two duplicate indexes are output separated by a comma.
- Action
-
Revise the settings so that element values are not duplicated.
-
KDCZ00196-E
The deletion of some parts failed because some parts are referenced from other parts. Cancel the references and then delete the parts, or select the part referencing the applicable parts and then delete all the parts. (Guide Part ID of the part that cannot be deleted = Guide-Part-ID-of-the-part-that-cannot-be-deleted, list of Guide Parts referencing the parts = list-of-referenced-Guide-Part-IDs)
- Cause
-
The deletion processing was suspended because there was a part that cannot be deleted.
- Action
-
If there are multiple parts that cannot be deleted because they are referenced by another part, the message displays the guide part ID of only the first such part subject to deletion processing. guide-part-IDs-list-for-source-parts in the message displays the guide part IDs separated by a comma. Take one of the following corrective actions on the part displayed in the message:
-
Cancel the reference relationship.
-
Select the source part, and then both cancel the reference relationship and delete the source part.
-
-
KDCZ00197-E
A parent Guide Part ID setting is incorrect. You cannot loop the parent and the children in the drop-down. (loop state = loop-state)
- Cause
-
There is an error in the settings for a parent guide part ID. The parent-child relationship in the drop-down cannot be looped.
- Action
-
looping-guide-part-IDs in the message displays the guide part IDs whose parent-child relationship is looping. An example is shown below.
- Example of looping guide part IDs:
-
D002 -> D001 -> D002
D001 -> D002 indicates that D001 has been set as the parent drop-down of D002. This example results in an error because it attempts to specify D002 as a parent drop-down although the parent-child relationship has already been established between D001 and D002. Revise the settings so that no looping occurs in the parent-child relationship in the drop-down.
-
KDCZ00198-E
A parent Guide Part ID setting is incorrect. You cannot set a Guide Part with a blank Guide Part ID for a parent Guide Part ID.
- Cause
-
There is an error in the parent's guide part ID setting. If the guide part ID is an empty character string, no guide part ID can be specified for the parent.
- Action
-
Specify a non-empty character string for the guide part ID, and then specify the parent's guide part ID.
-
KDCZ00200-E
You must set different values for the Guide Part ID and the parent Guide Part ID.
- Cause
-
The same value was specified for the guide part ID and the parent's guide part ID.
- Action
-
Specify different values for the guide part ID and the parent's guide part ID.
-
KDCZ00201-E
No more selections can be added to the list. (maximum number of selections for a list = maximum-number-of-items-in-the-selection-list)
- Cause
-
The Add button was clicked when the parent value or the number of selected items in the list had reached the maximum.
- Action
-
Revise the selected items so that their number is within the upper limit.
-
KDCZ00202-E
A validation rule setting is incorrect. You cannot use control characters (such as tabs).
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x09, 0x0B to 0x1F, and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00203-E
A validation rule setting is incorrect. Specify the correct regular expressions for JavaScript. (cause = message-for-the-run-time-error)
- Cause
-
A syntax error was detected in the regular expression.
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00204-E
If you set a validation rule, you must set the error message that is displayed if an error occurs when the entered value is checked.
- Cause
-
No error message was specified when an input rule was specified.
- Action
-
Set a valid value for the error message.
-
KDCZ00205-E
An error message setting is incorrect. You cannot use control characters (such as tabs).
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00207-E
The setting the-name-of-the-back-button-for-this-node, name-of-the-next-button-for-the-previous-node, name-of-the-complete-button-for-the-previous-node, or the-name-of-the-search-keyword-for-the-HTML-part-attribute is incorrect. You cannot use control characters (such as tabs).
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00208-Q
All Plugin Parts of all Operational Contents will be updated by synchronizing with the plugins that have already been imported. This processing might take time. Do you want to continue?
Note: If you continue with the processing, do not perform any other operation with the Web browser until the completion message is displayed.
- Cause
-
The Updating Plugin Parts menu was clicked in the Operational Content Editing window.
-
KDCZ00209-E
HTML-source-string-characters exceeds the maximum number of characters allowed. (maximum number of characters = 65535)
- Cause
-
The specified setting exceeds the maximum number of characters (the number of characters output by the argument).
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00210-E
The setting HTML-source-string-characters is incorrect. You cannot use control characters except for line feed/tab characters.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x08, 0x0B to 0x0C, 0x0E to 0x1F, and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00211-E
A setting for the display order of the windows is incorrect. You must set the display order of the windows in the range from 1 to 100.
- Cause
-
The specified display order is invalid. The possible cause is as follows:
-
A specified numeric value is outside the range from 1 to 100 (expressed with single-byte numeric characters).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00212-E
You cannot omit name-of-the-item-where-the-error-occurred.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
No sort order (ascending or descending) is specified.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00218-Q
Are you sure you want to delete the selected files or folders?
This processing might take a long time.
- Cause
-
You requested deletion of a file or a folder in the File Management/Registration window.
- Action
-
To delete the selected file or folder, click the OK button.
To not delete the selected file or folder, click the Cancel button.
-
KDCZ00219-E
You cannot use one-byte or double-byte spaces before or after the name of the file to be uploaded.
- Cause
-
The name of the file to be uploaded begins or ends with a single-byte or double-byte space.
- Action
-
Change the name of the file to be uploaded so that it does not begin or end with a space, and then click the Browse button to select the file and upload it.
-
KDCZ00220-E
The name of file to be uploaded is too long. (maximum length of path = maximum-length-of-path characters)
- Cause
-
The length of the target path exceeds the maximum length because the name of the file to be uploaded is too long.
- Action
-
Rename the file so that its file name does not exceed the number of characters output in the argument, and then upload the file again.
The number of characters output in the argument is obtained from the following formula:
-
250 - Navigation-Platform-installation-directory\PP\uCPSB\httpsd\htdocs\ucnpuserstaticfiles\
-
-
KDCZ00221-E
The name of the file to be uploaded contains invalid characters. (entered value = entered- file-name)
- Cause
-
The setting that was entered is invalid. The possible causes are as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
The setting contains characters that are not permitted in Windows folder or file names (\, /, :, *, ?, ", <, >, and |).
-
The setting consists of only a period (.).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00222-E
You cannot specify a reserved device name as the name of the file to be updated. (entered value = entered-value (file-name))
- Cause
-
The entered file name contains a Windows reserved device name (AUX, CON, NUL, PRN, COM1 to COM9, and LPT1 to LPT9).
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00223-Q
The [File Management/Registration] window is already open. Do you want to refresh the window?
Note: If the [File Management/Registration] window is being processed, click the [Cancel] button.
- Cause
-
The File Management/Registration window is already open.
- Action
-
If you want to refresh the File Management/Registration window, click the OK button.
If you want to do nothing, click the Cancel button.
- Supplementary information
-
You can change the contents of this message by specifying the user message properties file (ucnp_message_user.properties). For details, see the Hitachi Navigation Platform Setup and Operations Guide.
-
KDCZ00225-E
The file you specified does not exist.
- Cause
-
The specified file does not exist.
- Action
-
-
Check if the input value ends with a backslash (\) or a forward slash (/).
-
Check and, if necessary, revise the input value.
-
-
KDCZ00226-E
The path of the file to be uploaded is invalid.
- Cause
-
The setting that was entered is invalid. The possible causes are as follows:
-
A relative path was specified for the file to be uploaded.
-
An invalid path was specified.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00227-I
The URL of the file was copied to the clipboard.
the-URL-of-the-file
- Cause
-
The URL of the file was copied to the clipboard.
-
KDCZ00228-W
The URL of the file could not be copied to the clipboard.
the-URL-of-the-file
- Cause
-
The possible causes are as follows:
-
In the Web browser's security settings, the Allow paste operations via script option is disabled.
-
In the security configuration dialog box displayed from the Web browser, Do not allow was selected.
-
- Action
-
-
Check and, if necessary, revise the Web browser's security settings.
-
Close and then reopen the window.
-
-
KDCZ00229-I
The URL for displaying the Operational Contents was copied to the clipboard.
URL
- Cause
-
The URL of the current operational content was acquired and then copied to the clipboard.
-
KDCZ00230-W
The URL for displaying the Operational Contents could not be copied to the clipboard.
URL
- Cause
-
The possible causes are as follows:
-
In the Web browser's security settings, the Allow paste operations via script option is disabled.
-
In the security configuration dialog box displayed from the Web browser, Do not allow was selected.
-
- Action
-
-
Check and, if necessary, revise the Web browser's security settings.
-
Close and then reopen the window.
-
-
KDCZ00231-E
The group name exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters-for-the-group-name)
- Cause
-
The group name exceeds the maximum number of characters.
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00232-E
The group name setting is incorrect. You cannot use control characters (such as tabs) in group names.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00233-E
To use the Preview function, save the Operational Content.
- Cause
-
The Preview button was clicked before the operational content being edited had been saved.
- Action
-
Click the Save button to save the operational content, and then click the Preview button.
-
KDCZ00234-E
To print, save the Operational Content.
- Cause
-
The Print button was clicked while the operational content was being edited.
- Action
-
Click the Save button to save the operational content, and then click the Print button.
-
KDCZ00235-E
Select one or more access rights groups from the available access rights groups, and then set them to the Operational Content.
- Cause
-
No access permission group has been selected from the available access permission groups for the operational content.
- Action
-
Select one or more access permission groups from the available access permission groups for the operational content, and then click the OK button.
If you want to exclude all available access permission groups for the target operational content, contact the system administrator.
-
KDCZ00236-E
You cannot omit the Operational Content name.
- Cause
-
The setting that was entered is invalid. The possible causes are as follows:
-
The setting consists of only an empty character string.
-
The setting consists of only double-byte or single-byte spaces.
-
- Action
-
Check and, if necessary, revise the entered operational content name.
-
KDCZ00237-E
A maximum of 10 access rights groups can be set to one Operational Content.
- Cause
-
More than 10 access permission groups have been set for the operational content.
- Action
-
Reduce the number of access permission groups that are to be set for the operational content to no more than 10, and then click the OK button.
-
KDCZ00238-E
Select one or more JP1 resource groups from the available JP1 resource groups, and then set them to the Operational Content.
- Cause
-
None of the available JP1 resource groups has been selected.
- Action
-
Select one or more of the available JP1 resource groups, and then click the OK button.
If you want to exclude all available access JP1 resource groups for the target content, contact the system administrator.
-
KDCZ00239-E
A maximum of 10 JP1 resource groups can be set to one Operational Content.
- Cause
-
More than 10 JP1 resource groups have been set for the operational content.
- Action
-
Reduce the number of JP1 resource groups that are to be set for the operational content to no more than 10, and then click the OK button.
-
KDCZ00240-E
Enter the value in the text box.
- Cause
-
No value was entered in the text box.
- Action
-
Enter a value in the text box.
-
KDCZ00241-E
You can use only one-byte alphanumeric characters and underscores (_).
- Cause
-
Characters other than single-byte alphanumeric characters and single-byte underscores (_) are used.
- Action
-
Enter a character string that consists of only single-byte alphanumeric characters and single-byte underscores (_).
-
KDCZ00242-E
This JP1 resource group has already been set.
- Cause
-
An attempt was made to add a JP1 resource group that has already been specified.
- Action
-
The same JP1 resource group cannot be specified more than once. Check and, if necessary, revise the value that was entered.
-
KDCZ00243-E
Multiple Plugin Parts for the same I/O Plugin cannot be allocated within the same guide. (I/O Plugin name = I/O-Plugin-name)
- Cause
-
The plugin part of the same I/O plugin has already been placed in the same guide.
- Action
-
Delete the plugin part that has already been placed in the same guide.
-
KDCZ00244-E
You cannot omit the parameter name.
- Cause
-
The value that was entered is invalid. No parameter name was entered.
- Action
-
Revise the value that was entered.
-
KDCZ00245-E
You can use only one-byte alphanumeric characters, spaces, hyphens (-), periods (.), and underscores (_) in parameter names.
- Cause
-
The value that was entered is invalid.
The parameter name contains a character other than the following:
-
Single-byte alphanumeric characters
-
Single-byte space
-
Single-byte hyphens (-)
-
Single-byte period (.)
-
Single-byte underscores (_)
-
- Action
-
Revise the value that was entered.
-
KDCZ00246-E
You cannot specify the same name for multiple parameters.
- Cause
-
The value that was entered is invalid.
The parameter name is duplicated.
- Action
-
Revise the value that was entered.
-
KDCZ00247-E
The parameter description exceeds 64 characters.
- Cause
-
The value that was entered is invalid.
A string consisting of more than 64 characters was specified as the description of a parameter.
- Action
-
Revise the value that was entered.
-
KDCZ00248-E
You cannot use control characters other than line feeds (such as tabs) in parameter descriptions.
- Cause
-
The value that was entered is invalid.
The description of a parameter contains control characters (characters represented by the ASCII codes 0x00 to 0x09, 0x0B to 0x0C, 0x0E to 0x1F, and 0x7F).
- Action
-
Revise the value that was entered.
-
KDCZ00249-E
To output the mapping list, save the Operational Content.
- Cause
-
The Mapping List button was clicked while operational content was being edited.
- Action
-
Use the Save button to save the operational content, and then click the Mapping List button.
-
KDCZ00250-W
You cannot paste the Data Store Plugin for other Operational Contents. The Data Store Plugin parts were deleted from the Process Node that you pasted. If the Data Store Plugin parts are necessary, assign them again.
- Cause
-
The source process node contained a Data Store Plugin, but the plugin was deleted during a paste operation.
- Action
-
When a process node is copied and pasted to another operational content, the Data Store Plugin part is not copied. If necessary, place a Data Store Plugin part again, and then redraw a mapping line.
-
KDCZ00251-W
If you abort the editing operation for the parameter of the Data Store Plugin parts, you cannot paste the Data Store Plugin parts that you copied before the abort procedure. The Data Store Plugin parts were deleted from the Process Node that you pasted. If the Data Store Plugin parts are necessary, assign or copy them again.
- Cause
-
The parameter editing operation on a Data Store Plugin part was discarded, but a process node containing the Data Store Plugin part that was copied before the operation was discarded was pasted.
- Action
-
If a parameter editing operation on a Data Store Plugin part is discarded, the Data Store Plugin part cannot be pasted by pasting a process node containing the Data Store Plugin part that was copied before the operation was discarded.
If you need the Data Store Plugin part, either place it or copy it again.
-
KDCZ00252-E
A service group name setting is incorrect. The service group name contains invalid characters.
- Cause
-
A setting that was entered is invalid.
The service group name contains control codes (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F to 0x9F).
- Action
-
Check and revise the entered setting.
-
KDCZ00253-E
You cannot omit the service group name.
- Cause
-
The value that was entered is invalid. An empty character string was specified for the service group name.
- Action
-
Revise the value that was entered.
-
KDCZ00254-E
A service name setting is incorrect. The service name contains invalid characters.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F to 0x9F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00255-E
You cannot omit the service name.
- Cause
-
The value that was entered is invalid. An empty character string was specified for the service name.
- Action
-
Revise the value that was entered.
-
KDCZ00256-E
A task name setting is incorrect. The task name contains invalid characters.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F to 0x9F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00257-E
A task description setting is incorrect. The task description contains invalid characters.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F to 0x9F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00258-E
A property key setting is incorrect. The property key contains invalid characters.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F to 0x9F).
-
- Action
-
Revise the value that was entered.
-
KDCZ00259-E
You cannot omit the property key.
- Cause
-
The value that was entered is invalid. An empty character string was specified for the property key.
- Action
-
Revise the value that was entered.
-
KDCZ00260-E
You cannot specify the same property key.
- Cause
-
The value that was entered is invalid. The same property key was specified more than once.
- Action
-
Revise the value that was entered.
-
KDCZ00261-E
A property value setting is incorrect. The property value contains invalid characters.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F to 0x9F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00262-E
You cannot omit the property value.
- Cause
-
The value that was entered is invalid. An empty character string was specified for the property value.
- Action
-
Revise the value that was entered.
-
KDCZ00263-E
A property description setting is incorrect. You cannot use control characters other than line feeds (such as tabs) in property descriptions.
- Cause
-
The setting that was entered is invalid. The parameter description contains control characters (characters represented by the ASCII codes 0x00 to 0x09, 0x0B to 0x0C, 0x0E to 0x1F, and 0x7F).
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00264-E
The property description exceeds 64 characters.
- Cause
-
The value that was entered is invalid. A string consisting of more than 64 characters was specified as the description of a property.
- Action
-
Revise the value that was entered.
-
KDCZ00265-E
The number of bytes for the setting value exceeds the maximum. (maximum = 1024, number of bytes of the setting value = number-of-bytes-of-the-setting-value)
- Cause
-
The length (in bytes) of the value that was entered exceeds the maximum.
- Action
-
- For JP1/AO URL output plugins:
-
Check and, if necessary, revise the value that was entered and reduce its length by, for example, omitting optional properties.
If the problem persists, consider using the Automatic Operation Service Execution plugin.
-
KDCZ00266-Q
Some plugins take time to be executed. Do you want to continue?
- Cause
-
Execution of a plugin that requires confirmation of its execution was requested.
- Action
-
To continue the processing, click the OK button.
To discontinue the processing, click the Cancel button.
-
KDCZ00267-E
You cannot omit the anchor string.
- Cause
-
The setting that was entered is invalid. Only an empty character string or spaces were specified.
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00268-E
A service name setting is incorrect. You cannot use control characters (such as tabs) in service names.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F to 0x9F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00269-E
A property value setting is incorrect. You cannot use control characters (such as tabs) in property values.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F to 0x9F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00270-Q
The information you set for opening the service execution window will be initialized. Do you want to continue?
- Cause
-
The Displays the window to execute the service. check box was cleared.
- Action
-
To continue the processing, click the OK button.
To discontinue the processing, click the Cancel button.
-
KDCZ00301-E
You cannot omit the anchor string. (line number = the-number-of-a-line-where-an-error-occurred)
You cannot omit the anchor string. (line number = the-line-number-where-the-error-occurred)
- Cause
-
The setting that was entered is invalid. The possible causes are as follows:
-
No anchor character string was entered.
-
Only double-byte or single-byte spaces were entered as the anchor character string.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00302-E
The anchor string exceeds the maximum number of characters allowed. (maximum number of characters = 1024 bytes, line number = the-number-of-a-line-where-an-error-occurred)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting is greater than 1,024 bytes in UTF-8.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00303-E
An anchor string setting is incorrect. You cannot use control characters (such as tabs) in anchor strings. (line number = the-number-of-a-line-where-an-error-occurred)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00304-E
A URL exceeds the maximum number of characters allowed. (maximum number of characters = 1024 bytes, line number = the-number-of-a-line-where-an-error-occurred)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting is greater than 1,024 bytes in UTF-8.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00305-E
A URL setting is incorrect. You cannot use control characters (such as tabs) in URLs. (line number = the-number-of-a-line-where-an-error-occurred)
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00307-E
Check the unchecked items.
- Cause
-
There is an unchecked check box.
- Action
-
Check the contents of the unchecked check box, check the check box if necessary, and then perform the operation again.
- Supplementary information
-
You can change the contents of this message by specifying the user message properties file (ucnp_message_user.properties). For details, see the Hitachi Navigation Platform Setup and Operations Guide.
-
KDCZ00308-E
The setting the-height-or-width-of-the-name-of-the-set-item is incorrect. The value of the-height-or-width-of-the-name-of-the-set-item must be set in the range of minimum-value to maximum-value.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The entered value falls outside the permitted range.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00309-Q
The values you edited will be discarded. Do you want to continue?
- Cause
-
The Discard Edits button was clicked.
- Action
-
To discard the edited contents, click the OK button. To not discard the edited contents, click the Cancel button.
-
KDCZ00310-E
To display the window that shows the differential values, save the Operational Content.
- Cause
-
The Differences button was clicked while the operational content was being edited.
- Action
-
Click the Save button to save the operational content, and then click the Differences button.
-
KDCZ00312-E
A comment setting is incorrect. You cannot use control characters other than line feeds (such as tabs) in comments.
- Cause
-
The setting that was entered is invalid. The possible cause is as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x09, 0x0B to 0x0C, 0x0E to 0x1F, and 0x7F).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00313-E
A comment exceeds the maximum number of characters allowed. (maximum number of characters = maximum-number-of-characters)
- Cause
-
The comment exceeds the maximum number of characters.
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00314-Q
The Operational Content that is being edited by another user will be unlocked, and the data being edited will be discarded. Do you want to continue?
- Cause
-
An attempt was made to unlock the operational content in the Operational Content Editing window.
- Action
-
If you want to unlock the operational content, click the OK button. Otherwise, click the Cancel button.
-
KDCZ00321-E
Select one or more of the Operational Contents whose reservations you want to cancel, and then perform the operation.
- Cause
-
No operational content whose reservation is to be deleted is selected.
- Action
-
Select one or more operational contents whose reservation is to be deleted, and then delete the reservation.
-
KDCZ00322-Q
The update of the Plugin Part might take a long time (hours). Estimate the execution time beforehand.
If you stop the update of a Plugin Part, you need to roll back all the Operational Content. Make sure there are backups of all the Operational Content.
Are you sure you want to update the Plugin Part?
- Cause
-
An attempt was made to perform plugin part update processing.
- Action
-
To perform plugin part update processing, click the OK button. Otherwise, click the Cancel button.
-
KDCZ00323-W
No I/O Plugin is selected.
- Cause
-
Operational content including the selected I/O Plugins is selected as the target of updating plugin parts, but no I/O plugin is selected.
- Action
-
Select one or more I/O plugins, and then perform the operation.
-
KDCZ00324-Q
If you stop the update of a Plugin Part, you need to roll back all the Operational Content.
When you update the Plugin Part again, the Operational Content that has already been updated will be processed again.
Are you sure you want to stop the update?
- Cause
-
An attempt was made to stop the plugin part update processing.
- Action
-
To stop the plugin part update processing, click the OK button. Otherwise, click the Cancel button.
-
KDCZ00325-E
You must enter a folder name.
- Cause
-
The setting that was entered is invalid. The possible causes are as follows:
-
The setting consists of only an empty character string.
-
The setting consists of only double-byte or single-byte spaces.
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00327-E
The folder name is too long. (maximum length = maximum-length characters)
- Cause
-
The setting that was entered exceeds the maximum number of characters (the maximum number of characters output by arguments).
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00328-E
The folder name contains an invalid character. (input characters = input-characters)
- Cause
-
The setting that was entered is invalid. The possible causes are as follows:
-
The setting contains control characters (characters represented by the ASCII codes 0x00 to 0x1F and 0x7F).
-
The setting contains characters that are not permitted in Windows folder or file names (\, /, :, *, ?, ", <, >, and |).
-
The setting contains only a period (.).
-
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ00329-E
You cannot specify a reserved device name for the folder name. (input name = input-name)
- Cause
-
The entered folder name contains a Windows reserved device name (AUX, CON, NUL, PRN, COM1 to COM9, and LPT1 to LPT9).
- Action
-
Check and, if necessary, revise the entered setting.
-
KDCZ08001-E
An error occurred during the transmission. (details = error-message)
- Cause
-
A communication error occurred.
- Action
-
Take the following corrective action:
-
User
Perform the failed operation again.
Check if a connection with the network can be established.
If the problem persists, contact the system administrator.
-
System administrator
Check if the server is running normally.
Another possibility is that an unexpected error has occurred in the I/O plugin. Check the I/O plugin for any problem.
-
-
KDCZ08002-E
An error occurred during the transmission.
- Cause
-
A communication error occurred.
- Action
-
Take the following corrective action:
-
User
Perform the failed operation again. If the problem persists, contact the system administrator.
-
System administrator
Check if the server is running normally.
-
-
KDCZ09001-E
An inconsistency occurred in the processing. (function ID = maintenance-information)
- Cause
-
There was an inconsistency in internal data.
- Action
-
Contact your customer support center.
-
KDCZ09002-E
Some Operational Content IDs in the Operational Contents list data are incorrect. (function ID = maintenance-information)
- Cause
-
The operational content ID is NULL.
- Action
-
Contact your customer support center.