To modify defined information:

1. Terminate the import processing or the target Datareplicator.
   If the target Datareplicator has terminated abnormally and an initial start is to be executed subsequently, start it normally, and then modify the defined information.
   
2. Use a text editor to modify the defined information.
3. Start the system in a start mode that will apply the modified information, as shown in the following table.
   

   Table 5-14 Start mode that applies the modified import environment definition

   Operand name	Start mode that applies the modified information
   	Initial start or partial initial start#1	Normal start#1	Import processing start#2
   qufilexxx#3	Y	--	--
   queuesize	Y	--	--
   reffile	Y	Y	Y
   statsfile#4	Y	--	--
   statssize	Y	--	--
   unreffile1	Y	--	--
   unreffile2	Y	--	--
   unreffilesz	Y	Y	--
   startmode#5	Y	Y	--
   restartmode#5	Y	Y	--
   breaktime#5	Y	Y	--
   breakmode#5	Y	Y	--
   eventtrn	Y	--	--
   eventtbl	Y	--	--
   eventretrn	Y	--	--
   eventretbl	Y	--	--
   eventcntreset	Y	Y	--
   eventspd	Y	--	--
   defmerge	Y	Y	Y
   cmtintvl	Y	Y	Y
   trncmtintvl	Y	Y	Y
   tblcmtintvl	Y	Y	Y
   tblcheck	Y	Y	Y
   defshmsize	Y	Y	Y
   ebcdic_type	Y	Y	Y
   shiftspace_cnv	Y	Y	Y
   undefcode_cnv	Y	Y	Y
   ref_data_backspace	Y	Y	Y
   skip_sqlcode	Y	Y	Y
   skip_mvcelmwarn	Y	Y	Y
   sqlerr_skip_info	Y	Y	Y
   extract_init	Y	Y	--
   db_connect_retry_number	Y	Y	Y
   db_connect_retry_interval	Y	Y	Y
   skip_codecnv_error	Y	Y	Y
   int_trc_getl	Y	Y	--
   devicexx#6	Y	--	--
   ujcodekind	Y	--	--
   discintvl	Y	Y	Y
   ref_wait_interval	Y	Y	Y
   commit_wait_time	Y	Y	Y
   mapping_key_check	Y	Y	Y
   control_trigger	Y	--	--
   control_reference_trigger	Y	--	--
   check_pending	Y	--	--
   reflect_delay_limit_time	Y	Y	Y
   sql_lockerr_retrynum	Y	Y	Y
   xa_recovery_retry_count	Y	Y	Y
   xa_recovery_retry_interval	Y	Y	Y
   reflect_trn_max_sqlnum	Y	Y	Y

Legend:

Y: The start mode denoted by this column applies the operand's modified information. If the start modes of multiple columns apply a particular operand's modified information, any one of those start modes can be used to apply the modified information.

--: Not applicable

#1

This is the start mode used to start the target Datareplicator.

#2

This is the start mode used to start the target Datareplicator's import processing.

#3

xxx is a value in the range from 001 to 008.

#4

If you are executing a normal start, do not change the statsfile operand.

#5

If the target Datareplicator terminated with an error or in the forced termination mode, it inherits the operand settings in effect at the time of the previous termination in order to maintain conformity between the source and target databases.

#6

xx is a value in the range from 01 to 09.