Job Management Partner 1/Automatic Job Management System 3 Command Reference 1

1.5.1 Commands used to set up JP1/AJS3

The following table lists the commands used to set up JP1/AJS3:

For details about the setup commands, see 2. Commands Used during Setup in the manual Job Management Partner 1/Automatic Job Management System 3 Command Reference 2.

Table 1-8 Commands used to set up JP1/AJS3

Function	Command name	Windows	UNIX	Required privileges	Supported products
Sets up the operating environment that corresponds to the logical host for JP1/AJS3 - Manager and JP1/AJS3 - Agent.	jp1ajs2_setup_cluster#1	--	Y	UNIX: Superuser	M and A
Sets up a database to be used by scheduler services. Sets up suspend functions.	ajssetup	Y	Y	Windows: Administrators UNIX: Superuser	M
Sets the mail distribution functions.	jpomailrecv	--	Y	None	M and A
Registers the VOS3 user information.	jpqreguser#1	Y	Y	None (In Windows Server 2008, Administrators except when the -a option is specified)	M and A
Registers information about a user assumed to be a JP1 user.	jpqregguestuser#1	Y	Y	Windows: Administrators UNIX: Superuser	M
Prevents increase of the number of shared memory segments.	jpqshmake#2	--	Y	UNIX: Superuser	M and A
Creates or deletes an adapter command setting file used to link JP1/IM.	ajs_adapter_setup	Y	Y	Windows: Administrators UNIX: Superuser	M
Sets up an embedded database environment.	ajsembdbsetup	Y	Y	Windows: Administrators UNIX: Superuser	M
Builds an embedded database environment.	ajsembdbbuild	Y	Y	Windows: Administrators UNIX: Superuser	M
Removes setup of an embedded database.	ajsembdbunset	Y	Y	Windows: Administrators UNIX: Superuser	M
Displays the information necessary for a command that is used to manipulate the embedded database and that is registered in the configuration definition.	ajsembdbidlist	Y	Y	Windows: Administrators UNIX: Superuser	M
Sets up the execution environment for the definition pre-check function.	ajschksetup	Y	Y	Windows: Administrators UNIX: Superuser	M and A
Defines JP1/AJS3 environment setting parameters.	jajs_config	Y	Y	Windows: Administrators UNIX: Superuser	M and A
Sets up JP1/AJS3.	jajs_setup	Y	Y	Windows: Administrators UNIX: Superuser	M
Sets up the operating environment corresponding to the JP1/AJS3 logical host.	jajs_setup_cluster	Y	Y	Windows: Administrators UNIX: Superuser	M and A
After JP1/AJS2 is upgraded to JP1/AJS3, sets up JP1/AJS3 so that it is in the standard configuration.	jajs_migrate	Y	Y	Windows: Administrators UNIX: Superuser	M
Exports the scheduler service data to a binary file from the database in an environment of JP1/AJS2 Version 8 or earlier.	ajscnvdbexport	Y	Y	Windows: Administrators UNIX: Superuser	M
Imports database backup data to a scheduler database.	ajscnvdbimport	Y	Y	Windows: Administrators UNIX: Superuser	M
Installs the JP1/AJS3 standard database (embedded database).	ajsembdbinstl	Y	Y	Windows: Administrators UNIX: Superuser	M
Uninstalls the JP1/AJS3 standard database (embedded database).	ajsembdbuninstl	Y	Y	Windows: Administrators UNIX: Superuser	M

Legend:

Y: Supported

--: Not supported

M: JP1/AJS3 - Manager

A: JP1/AJS3 - Agent

Note

On a Windows Server 2008 host, before you execute a command that must be executed by a member of the Administrators group, make sure that you open the Command Prompt window as an administrator. To do this, on the Windows Start menu, right-click Command Prompt, and then choose Run as administrator. If the UAC function is disabled, you do not need to open the Command Prompt window as an administrator.

#1

Do not execute this command if a JP1 series product that requires JP1/Base is running.

#2

If JP1/AJS3 has been installed as an upgrade installation from JP1/AJS2 06-71-/G or an earlier version, you need to execute this command only once after setup. You do not need to execute the command again. If JP1/AJS3 has been installed as a new installation, you do not need to execute this command.

[Contents][Back][Next]

Copyright (C) 2009, 2010, Hitachi, Ltd.
Copyright (C) 2009, 2010, Hitachi Solutions, Ltd.