Job Management Partner 1/Performance Management Planning and Configuration Guide

[Contents][Glossary][Index][Back][Next]

5.4.5 Changing IP address settings

This subsection describes the procedures to change IP addresses during Performance Management operation.

Organization of this subsection
(1) Changing the IP address of the PFM - Manager host
(2) Changing the IP address of the PFM - Web Console host
(3) Changing the IP address of the PFM - Base host
(4) Changing the IP address of the PFM - Agent or PFM - RM host

(1) Changing the IP address of the PFM - Manager host

To change the IP address of the PFM - Manager host:

  1. Log out from PFM - Web Console.
    Log out from all PFM - Web Console hosts that connect to the PFM - Manager host for which you intend to change the IP address.

  2. Stop all Performance Management services on the PFM - Manager host.
    Stop all Performance Management programs and services on the PFM - Manager host for which you intend to change the IP address. To stop the services, use the jpcspm stop command. If the programs are running on a cluster system, stop them from the cluster software.

  3. Change the IP address of the PFM - Manager host.
    Change the IP address of the monitoring manager host where PFM - Manager is installed.

  4. Configure the network.
    Configure the network to allow TCP communication by all PFM - Agent, PFM - RM, PFM - Base, PFM - Web Console and PFM - Manager hosts to the host whose IP address you changed.

  5. Restart the Performance Management services on the PFM - Manager host.
    Start the Performance Management programs and services on the PFM - Manager host. If the programs are running on a cluster system, stop them from the cluster software.

  6. Log on to PFM - Web Console.
    Log on to PFM - Web Console.

(2) Changing the IP address of the PFM - Web Console host

To change the IP address of the PFM - Web Console host:

  1. Stop all Performance Management services on the PFM - Web Console host.
    Stop all Performance Management programs and services on the PFM - Web Console host for which you intend to change the IP address by using the jpcwstop command. If running the programs on a cluster system, stop them from the cluster software.

  2. Change the IP address of the PFM - Web Console host.
    Change the IP address of the monitoring console host where PFM - Web Console is installed.

  3. Configure the network.
    Configure the network to allow TCP communication from the connection-target PFM - Manager to the host whose IP address you changed, and to allow HTTP communication from the monitoring console to the host whose IP address you changed.

  4. Restart the Performance Management services on the PFM - Web Console host.
    Start the Performance Management programs and services on the PFM - Web Console host. If the programs are running on a cluster system, stop them from the cluster software.

  5. Log on to PFM - Web Console
    Connect to PFM - Web Console from the monitoring console, using the new IP address (or host name) in the URL.

(3) Changing the IP address of the PFM - Base host

To change the IP address of the PFM - Base host:

  1. Stop all Performance Management services on the PFM - Base host.
    Stop all Performance Management programs and services on the PFM - Base host for which you intend to change the IP address. To stop services, use the jpcspm stop command. If the programs are running on a cluster system, stop them from the cluster software.

  2. Change the IP address of the PFM - Base host.
    Change the IP address of the host where PFM - Base is installed.

  3. Configure the network.
    Configure the network to allow TCP communication by all PFM - Agent, PFM - RM, PFM - Base, PFM - Web Console, and PFM - Manager hosts to the host whose IP address you changed.

  4. Restart the Performance Management services on the PFM - Base host.
    Start the Performance Management programs and services on the host where PFM - Base is installed. If the programs are running on a cluster system, stop them from the cluster software.

(4) Changing the IP address of the PFM - Agent or PFM - RM host

To change the IP address of the PFM - Agent or PFM - RM host:

  1. Stop all Performance Management services on the PFM - Agent or PFM - RM host.
    Stop all Performance Management programs and services on the PFM - Agent or PFM - RM host for which you intend to change the IP address. To stop services, use the jpcspm stop command. If the programs are running on a cluster system, stop them from the cluster software.

  2. Change the IP address of the PFM - Agent or PFM - RM host.
    Change the IP address of the host where PFM - Agent or PFM - RM is installed.

  3. Configure the network.
    Configure the network to allow TCP communication by all PFM - Agent, PFM - RM, PFM - Base, PFM - Web Console and PFM - Manager hosts to the host whose IP address you changed.

  4. Restart the Performance Management services on the PFM - Agent or PFM - RM host.
    Start the Performance Management programs and services on the host where PFM - Agent or PFM - RM is installed. If the programs are running on a cluster system, stop them from the cluster software.

[Contents][Back][Next]

[Trademarks]

All Rights Reserved. Copyright (C) 2009, Hitachi, Ltd.