Hitachi Command Suite Software メッセージガイド

[目次][前へ][次へ]


4.5 KAIC40000~KAIC49999

Device Manager CLIEXに関するメッセージ(KAIC40000~KAIC49999)を次の表に示します。

表4-5 KAIC40000~KAIC49999:Device Manager CLIEXのメッセージ

メッセージID メッセージテキスト 説明
KAIC40001-E An unknown failure occurred in the target storage array. エラーが繰り返し発生する場合には,顧客問い合わせ窓口に連絡してください。
KAIC40002-E The command device has failed. <command device error message RAID Managerのマニュアルを参照してください。
KAIC40003-E~KAIC40699-E RAID Manager error message Device Manager CLIEX の障害対策とRAID Managerのマニュアルを参照してください。
KAIC41000-E An internal error occurred. (file = "<file name>", line = "<line number>"). 顧客問い合わせ窓口に連絡してください。
KAIC41001-E Memory allocation error. Out of memory. Device Manager CLIEXの実行に必要なメモリーが不足しているおそれがあります。
システムでメモリーが不足していないか確認してください。エラーが繰り返し発生する場合には,顧客問い合わせ窓口に連絡してください。
KAIC41002-E This command has not been supported for the target storage array. ストレージサブシステムの指定を見直してください。
KAIC41003-E An attempt to load the command device has failed. ホストがコマンドデバイスを正しく認識していることを確認してください。
KAIC41004-E An attempt to acquire the device information has failed. (device special file: "<device file name>") Check the status of the device associated with the device special file. デバイススペシャルファイルと関連づいた装置の状態を確認してください。
エラーが繰り返し発生する場合には,顧客問い合わせ窓口に連絡してください。
KAIC42000-E The storage-array parameter must be one of the following: "-c", "--cmddev", "-a", or "--array" ストレージサブシステムの指定を見直してください。
KAIC42001-E The storage-array parameter must be one of the following: "-c", "--cmddev", "-a", or "--array" ストレージサブシステムの指定を見直してください。
KAIC42002-E The specified storage array name "<alias name>" is invalid. Check the property file. プロパティファイルの記述を確認し,ストレージサブシステム名を見直してください。
KAIC42003-E A command argument is missing or invalid. コマンドの指定を見直してください。
KAIC42004-E The command must contain only one of the following: <command list コマンドの指定を見直してください。
KAIC42005-E The value "<parameter value>" for the parameter "<parameter name>" is invalid. パラメーターの指定を見直してください。
KAIC42006-E The value for the parameter "<parameter name>" must be between <minimum value> and <maximum value>. パラメーターの指定を見直してください。
KAIC42007-E The parameter "<parameter name>" is required. パラメーターの指定を見直してください。
KAIC42008-E The parameter "<parameter identifier or parameter name>" is invalid. パラメーターの指定を見直してください。
KAIC42009-E The parameter must be either "<parameter name>" or "<parameter name>". パラメーターの指定を見直してください。
KAIC42010-E The LUN "<path LUN>" has already been assigned to a LUN group or is not assigned to this port. ストレージサブシステムの情報を取得し,パラメーターの指定を確認してください。
KAIC42011-E The specified LDEV "<device number>" is invalid. ストレージサブシステムの情報を取得し,パラメーターの指定を確認してください。
KAIC42012-E The specified LDEV "<device number>" is part of the LU joined by the LUSE. パラメーターの指定を見直してください。
KAIC42013-E The LU "<device number>" is not assigned to the port "<port number>". ストレージサブシステムの情報を取得し,パラメーターの指定を確認してください。
KAIC42014-E The LUN "<path LUN>" is already being used. LUNの指定を見直してください。
KAIC42015-E To perform this operation, "LUNSecurity=On" must be set for the port. 指定ポートのセキュリティスイッチをON にしてから再実行してください。
KAIC42016-E The LU "<device number>" is already assigned to this port. ストレージサブシステムの情報を取得し,パラメーターの指定を確認してください。
KAIC42017-E The LU "<device number>" is not assigned to "<port-number> - <host storage domain ID>" (port - HostStorageDomain). ストレージサブシステムの情報を取得し,パラメーターの指定を確認してください。
KAIC42018-E The LUN "<path LUN>" is not assigned to the LUN group "<LUN group ID>". ストレージサブシステムの情報を取得し,パラメーターの指定を確認してください。
KAIC42019-E The host storage domain "<host storage domain ID>" already exists on this port. ストレージサブシステムの情報を取得し,パラメーターの指定を確認してください。
KAIC42020-E The WWN "<WWN>" has not been registered in "<LUNGroup or HSDOMAIN>": "<LUN group ID or host storage domain ID>". ストレージサブシステムの情報を取得し,パラメーターの指定を確認してください。
KAIC42021-E The WWN "<WWN>" has already been defined in the host storage domain "<host storage domain ID>". ストレージサブシステムの情報を取得し,パラメーターの指定を確認してください。
KAIC42022-E The maximum LUN number ("<maximum value>") on the port has been reached. パラメーターの指定を見直してください。
KAIC42023-E The host storage domain "<host storage domain ID>" has not been defined for the port "<port number>". ホストストレージドメインを確認してください。
KAIC42024-E The LU "<path LUN>" has already been assigned to a port. ストレージサブシステムの情報を取得し,パラメーターの指定を確認してください。
KAIC42025-E target volume> is not available for this operation. ボリュームの指定を見直してください。
KAIC42026-E The usual volume and the V-VOL can not be specified together. ボリュームの指定を見直してください。
KAIC42027-E At least one LUN is necessary for the pair volume. LUNの指定を見直してください。
KAIC42028-E Duplicated value "<parameter value>" for <parameter name> is specified. パラメーターの指定を見直してください。
KAIC42029-E The LU "<device number>" is already assigned to this host storage domain. ストレージサブシステムの情報を取得し,パラメーターの指定を確認してください。
KAIC42030-E ARRAY: "<array name>" is not attached this host or doesn't have valid CMDDEV. ホストがコマンドデバイスを正しく認識していることを確認してください。
KAIC42031-E The Command Device (devNum="<device number>", devFile="<device file name>") is not attached this host. Or, the storage array that has the Command Device is not supported. Revise devFile or devNum in the property file. ホストがコマンドデバイスを正しく認識していることを確認してください。
またコマンドデバイスが,Device Manager CLIEXがサポートするストレージサブシステムのコマンドデバイスであることを確認してください。
KAIC42100-E Permission denied with the Virtual Partition Manager, "<parameter name>": "<parameter value>". パラメーターの指定を見直してください。
KAIC42996-E Device Manager CLIEX cannot be started because the installation directory in the registry is invalid. Re-install Device Manager CLIEX. If this problem cannot be solved, contact the Support Center. この問題を解決できないときは,顧客問い合わせ窓口に連絡してください。
KAIC42997-E Device Manager CLIEX cannot be started because a registry entry is invalid. Re-install Device Manager CLIEX. If this problem cannot be solved, contact the Support Center. この問題を解決できないときは,顧客問い合わせ窓口に連絡してください。
KAIC42998-E Device Manager CLIEX cannot be started because the registry key is invalid. Re-install Device Manager CLIEX. If this problem cannot be solved, contact the Support Center. この問題を解決できないときは,顧客問い合わせ窓口に連絡してください。
KAIC42999-E The specified value "<specified value>" does not exist on the target "<target element>". パラメーターの指定を見直してください。
KAIC43300-E An attempt to load "<file name>" has failed. 顧客問い合わせ窓口に連絡してください。
KAIC43301-E The filename cannot contain any directories. プロパティファイルの指定を見直してください。
KAIC43302-E The file "<file name>" cannot be loaded. 顧客問い合わせ窓口に連絡してください。
KAIC43303-E The file cannot be opened. ("<file name>") プロパティファイルの指定を見直してください。
エラーが繰り返し発生する場合には,顧客問い合わせ窓口に連絡してください。
KAIC43500-E There are too many or too few elements in the message file. (file = "<file name>", line = "<line number>", string = "<line string>") 顧客問い合わせ窓口に連絡してください。
KAIC43502-E The log level in the message file is invalid. (file = "<file name>", line = "<line number>", string = "<line string>") 顧客問い合わせ窓口に連絡してください。
KAIC43503-E The message ID in the message file is invalid. (file = "<file name>", line = "<line number>", string = "<line string>") 顧客問い合わせ窓口に連絡してください。
KAIC43504-E A definition is duplicated in the message file. (file = "<file name>", line = "<line number>", string = "<line string>") 顧客問い合わせ窓口に連絡してください。
KAIC43505-E The number of sections in the message file is invalid. (file = "<file name>", line = "<line number>", string = "<line string>") 顧客問い合わせ窓口に連絡してください。
KAIC43506-E The message file "<file name>" is missing the message "<message ID>". 顧客問い合わせ窓口に連絡してください。
KAIC43550-E The file cannot be opened. ("<file name>") 顧客問い合わせ窓口に連絡してください。
KAIC43551-E The file cannot be written to. ("<file name>") 顧客問い合わせ窓口に連絡してください。
KAIC43552-E An attempt to open the event log has failed. Check the event log settings or change the Device Manager CLIEX settings so that event logs are not output to the event log. イベントログの設定を見直してください。
KAIC43553-E An attempt to output to the event log has failed. Check the event log settings or change the Device Manager CLIEX settings so that event logs are not output to the event log. イベントログの設定を見直してください。
KAIC43554-E An attempt to close the event log has failed. Check the event log settings or change the Device Manager CLIEX settings so that event logs are not output to the event log. イベントログの設定を見直してください。
KAIC44300-E The XML is invalid. (file = "<file name>", line = "<line number>", column = "<column number>", "<message>") プロパティファイルの記述を確認してください。
KAIC44301-E The XML is not well formed. (file = "<file name>", line = "<line number>", column = "<column number>", "<message>") プロパティファイルの記述を確認してください。
KAIC44302-E An error occurred during XML parser initialization. (file = "<file name>") エラーが繰り返し発生する場合には,顧客問い合わせ窓口に連絡してください。
KAIC44303-E An error occurred during parsing. ("<error message>") プロパティファイルの記述を確認してください。
KAIC44304-E A DOM error occurred during parsing. ("<error message>") プロパティファイルの記述を確認してください。
KAIC44305-E An error occurred during parsing. ("<error message>") プロパティファイルの記述を確認してください。
KAIC44306-E An error occurred during XML processing. ("<error message>") エラーが繰り返し発生する場合には,顧客問い合わせ窓口に連絡してください。
KAIC44400-E An error occurred while parsing "<file name>". This file does not conform to the DTD. プロパティファイルの記述を確認してください。

[目次] [前へ] [次へ]


All Rights Reserved. Copyright© 2010, 2014, Hitachi, Ltd.