Job Management Partner 1/Client Security Control Description, User's Guide and Operator's Guide

[Contents][Glossary][Index][Back][Next]

5.4.1 Installing JP1/CSC - Manager

Install JP1/CSC - Manager on the management server.

This subsection explains the procedures for installing JP1/CSC - Manager, for both a new installation and an overwrite installation.

Organization of this subsection
(1) Performing a new installation of JP1/CSC - Manager
(2) Performing an overwrite installation of JP1/CSC - Manager

(1) Performing a new installation of JP1/CSC - Manager

The following explains the procedures for performing a new installation of JP1/CSC - Manager. To install JP1/CSC - Manager, use the provided CD-ROM. Alternatively, use JP1/Software Distribution to perform remote installation. For details about remote installation using JP1/Software Distribution, see the manual Job Management Partner 1/Software Distribution Administrator's Guide Volume 1, for Windows systems. If the remote installation failed, use the provided CD-ROM to install JP1/CSC - Manager.

Note
Before installing JP1/CSC - Manager, you must have completed the installation and setup of Asset Information Manager or Asset Information Manager Subset Component of JP1/Software Distribution Manager. If neither of these products has been set up, you will be unable to set up the JP1/CSC - Manager environment. For details about how to install and set up Asset Information Manager Subset Component of JP1/Software Distribution Manager, see the manual Job Management Partner 1/Software Distribution Setup Guide, for Windows systems. For details about how to install and set up Asset Information Manager, see the manual Job Management Partner 1/Asset Information Manager Planning and Setup Guide.

To install JP1/CSC - Manager using the provided CD-ROM:

  1. Log on to Windows as a member of the Administrators group.

  2. Insert the provided CD-ROM in the drive.
    When the installer starts, a dialog box prompting you to select a component is displayed, so select the JP1/CSC - Manager component.

  3. Click the Install button.
    A dialog box is displayed prompting you to confirm the start of installation.

  4. Click the OK button.
    A dialog box is displayed indicating that JP1/CSC - Manager installation has started.

  5. Click the Next button.
    A dialog box is displayed, in which you can enter user information.

  6. Enter the user name and company name.

  7. Click the Next button.
    A dialog box is displayed in which you can specify the installation folder.

  8. Specify the installation folder.
    Installation is performed in the specified folder. The default installation destinations are as follows (when the OS is installed under C:\):

    For a 64-bit edition of Windows:
    C:\Program Files(x86)\HITACHI\jp1netmcscm

    For other OSs
    C:\Program Files\HITACHI\jp1netmcscm

  9. Click the Next button.
    A dialog box is displayed, in which you can select the program folder.

  10. Specify the program folder.
    Specify the folder to which the program icon is added. The default folder name is Client Security Control.

  11. Click the Next button.
    A dialog box is displayed in which automatic setup can be selected. To perform automatic setup, select the Perform setup processing check box.
    Note
    If you select automatic setup, stop the World Wide Web Publishing Service.

  12. Click the Next button.
    A dialog box is displayed confirming the current contents. Check the settings.

  13. Click the Next button.
    Installation begins.
    When installation is finished, a dialog box confirming whether or not to open the README file is displayed. Skip to step 15 if you click the No button.

  14. Read and then close the README file.
    When the README file is read and closed, a dialog box indicating that installation is complete is displayed.

  15. Click the Finish button.
    Installation is complete.

  16. Restart Windows.
    If the installation finished successfully, restart Windows.

Note
If automatic setup was not selected in step 11, restart the system after installation, stop the World Wide Web Publishing Service, and execute the cscsetup command. If automatic setup was selected in step 11 and an error occurred, check the log information, restart the system, and execute the cscsetup command. For details about the cscsetup command, see cscsetup (sets up JP1/CSC - Manager) in 15. Commands.

(2) Performing an overwrite installation of JP1/CSC - Manager

An overwrite installation of JP1/CSC - Manager can be performed when the version to be installed is the same or later than the existing one.

Note
Before you perform an overwrite installation, stop services in the following order:
  • World Wide Web Publishing Service
  • Asset Information Synchronous Service
  • Client Security Control - Manager
  • Client Security Control - Manager Remote Service

To perform an overwrite installation:

  1. Log on to Windows as a member of the Administrators group.

  2. Insert the provided CD-ROM in the drive.
    When the installer starts, a dialog box appears, prompting you to select a component. Select the JP1/CSC - Manager component.

  3. Click the Install button.
    A dialog box appears, prompting you to confirm the start of overwrite installation.

  4. Click the OK button.
    A dialog box appears, in which you can select automatic setup. To perform automatic setup, select the Perform an automatic setup check box.

  5. Click the Next button.
    Installation begins.
    When installation finished, a dialog box appears, asking whether you want to open the README file. Skip to step 7 if you click the No button.

  6. Read and then close the README file.
    When the README file is read and closed, a dialog box appears, indicating that installation is completed.

  7. Click the Finish button.
    Installation is complete. For an overwrite installation, you do not have to restart Windows.

Note that an overwrite installation cannot be performed if the version to be installed is earlier than the current version of JP1/CSC - Manager.

Note
If you did not select automatic setup in step 4, restart the system after installation, stop the World Wide Web Publishing Service, and then execute the cscsetup command. If you selected automatic setup in step 4 and an error occurred, check the log information, restart the system, and then execute the cscsetup command. For details about the cscsetup command, see cscsetup (sets up JP1/CSC - Manager) in 15. Commands.

[Contents][Back][Next]

[Trademarks]

All Rights Reserved. Copyright (C) 2009, 2011, Hitachi, Ltd.
Copyright, patent, trademark, and other intellectual property rights related to the "TMEng.dll" file are owned exclusively by Trend Micro Incorporated