Job Management Partner 1/Automatic Job Management System 3 Messages 2

[Contents][Glossary][Index][Back][Next]

1.5 Messages beginning with KNAD (Messages that are output by system management)

This section lists messages that begin with KNAD (messages output by system management).

KNAD3501-E

An attempt to open the message file has failed.

An attempt to open the message file has failed.

(S)
Terminates system management.

(O)

For Windows
Use the data collection tool to collect data, and then contact the system administrator.

For UNIX
Probable causes are listed below. Check the environment.
  • The files under /opt/jp1ajs2/lib/nls might not have read permission. Set read permission.
  • The maximum number of files that can be opened in the system might have been reached. Review the kernel parameter.
  • The cause might be a temporary memory shortage. Retry the operation, but only after terminating any unnecessary processes.
  • The directory or file might have been deleted. Re-installation is necessary.
If you are unable to solve the problem, use the data collection tool to collect data, and then contact the system administrator.

KNAD3502-E

An attempt to read the message file has failed.

An attempt to read the message file has failed.

(S)
Does not output any messages.

(O)
Check whether JP1/AJS3 setup has terminated normally.

KNAD3503-E

An attempt to read the message file has failed.

An attempt to read the message file has failed.

(S)
Does not output any messages.

(O)
Make sure that the message file (jajsspm.cat) is located under the /opt/jp1ajs2/lib/nls directory, and make sure that the reference permissions are suitable.

KNAD3504-E

An error occurred in internal processing to output a message.

An error occurred during internal processing of message output.

(S)
Does not output any messages.

(O)
Check whether there is a system resource shortage.

KNAD3516-E

An attempt to start the system management has failed. (errno = request-code)

An attempt to start system management has failed.

(S)
Terminates system management.

(O)
Check whether the product has been correctly installed.

KNAD3552-E

JP1/AJS3 management-target-process-name has timed out.

A request timeout has occurred. management-target-process-name is the name of a process configured from all components under the control of system management.

(S)
Continues processing.

(O)
For a reload request, increase the timeout value, and then retry the operation. For all other cases, wait for a while, and then re-execute the request. If the same problem occurs after re-execution, use the data collection tool to collect data, and then contact the system administrator.

KNAD3553-E

SIGKILL was sent to management-target-process-name of JP1/AJS3, but termination could not be detected.

SIGKILL was sent, but termination could not be detected. management-target-process-name is the name of a process configured from all components under the control of system management.

(S)
Terminates system management.

(O)
Use the data collection tool to collect data, and then contact the system administrator.

KNAD3554-I

A JP1/AJS3 reload request has finished.

A reload request has been completed.

(S)
Continues processing.

KNAD3564-I

jajs_xxxd: JP1/AJS3 will now start all inactive processes.

All stopped processes under management will be started. jajs_xxxd is one of the following:

  • jajs_spmd: System management
  • jajs_dbmd: DB service
  • jajs_hstd: Host service
  • jajs_agtd: Agent service
  • jajs_schd: Scheduler service

(S)
Continues processing.

KNAD3574-I

jajs_xxxd_reload: A reload request will now be sent to all running processes of JP1/AJS3.

A reload request will be sent to all running processes under management. jajs_xxxd is one of the following:

  • jajs_spmd: System management
  • jajs_dbmd: DB service
  • jajs_hstd: Host service
  • jajs_agtd: Agent service
  • jajs_schd: Scheduler service

(S)
Continues processing.

KNAD3577-I

jajs_xxxd_stop: A stop request will now be sent to all processes of JP1/AJS3.

A stop request will be sent to all processes under management. jajs_xxxd is one of the following:

  • jajs_spmd: System management
  • jajs_dbmd: DB service
  • jajs_hstd: Host service
  • jajs_agtd: Agent service
  • jajs_schd: Scheduler service

(S)
Continues processing.

KNAD3578-I

JP1/AJS3 has ended.

System management has terminated.

(S)
Terminates system management.

KNAD3586-I

JP1/AJS3 has terminated.

System management has terminated.

(S)
Terminates system management.

KNAD3597-I

jajs_xxxd_stop -kill: A forced stop (kill) will be performed on all processes of JP1/AJS3.

All processes under management will be forcibly stopped. jajs_xxxd is one of the following:

  • jajs_spmd: System management
  • jajs_dbmd: DB service
  • jajs_hstd: Host service
  • jajs_agtd: Agent service
  • jajs_schd: Scheduler service

(S)
Continues processing.

KNAD3599-E

main_loop: An invalid request was received. (event ID = request-type)

An invalid request has been received.

(S)
Continues processing.

(O)
Use the data collection tool to collect data, and then contact the system administrator.

KNAD3602-I

JP1/AJS3 received a startup report from management-target-process-name.

A startup completed notification has been received. management-target-process-name is the name of a process configured from all components under the control of system management.

(S)
Continues processing.

KNAD3603-I

All processes of JP1/AJS3 are running.

All processes under management have been started.

(S)
Continues processing.

KNAD3604-I

JP1/AJS3 startup has finished.

Service startup has been completed.

(S)
Continues processing.

KNAD3605-I

JP1/AJS3 completed to send the start up request to the management-target-process-name.

Restart of a process under management that terminated abnormally has been completed. management-target-process-name is the name of a process configured from all components under the control of system management.

(S)
Continues processing.

KNAD3608-I

JP1/AJS3 received a reload-completed notification from management-target-process-name.

A reload completed notification from a process under management has been received. management-target-process-name is the name of a process configured from all components under the control of system management.

(S)
Continues processing.

KNAD3609-I

A JP1/AJS3 reload request has finished.

Reload processing for all processes under management has finished.

(S)
Continues processing.

KNAD3610-I

JP1/AJS3 received an termination notification from management-target-process-name.

A termination notification from a process under management has been received. management-target-process-name is the name of a process configured from all components under the control of system management.

(S)
Continues processing.

KNAD3612-I

A stop request will now be sent to all processes of JP1/AJS3.

A stop request will be sent to all processes under management.

(S)
Continues processing.

KNAD3613-W

A JP1/AJS3 timeout occurred in management-target-process-name. Processing continues.

A startup timeout has occurred for a process under management. management-target-process-name is the name of a process configured from all components under the control of system management.

(S)
Continues processing.

(O)
Wait a while. If startup of the managed process has not been completed or JP1/AJS3 does not start, use the jajs_spmd_stop -kill command to force termination, and then restart the service.
If this message is output after the process terminated abnormally, restart might have failed due to too short a retry interval for the managed process. See 7.3.1 Restarting an abnormally terminated JP1/AJS3 process in the Job Management Partner 1/Automatic Job Management System 3 Administration Guide, and then adjust the retry interval.

KNAD3614-E

System management will now stop because an invalid JP1/AJS3 status occurred.

System management will stop due to an invalid status.

(S)
Terminates system management.

(O)
Check whether the KAVS2128-E message was output to the Windows event log (in Windows) or syslog (in UNIX). If the KAVS2128-E message was output, setup of the scheduler service has failed, in which case take the corrective action suggested in the message. If this message was output after the setup of the scheduler service terminated normally, use the data collection tool to collect data, and then contact the system administrator.

KNAD3616-I

Restart of the JP1/AJS3 management-target-process-name has finished.

Restart of a process under management that terminated abnormally has been completed. management-target-process-name is the name of a process configured from all components under the control of system management.

(S)
Continues processing.

KNAD3617-I

The JP1/AJS3 management-target-process-name startup has finished.

Startup of a process under management in JP1/AJS3 has been completed.

The name of a process configured from all components under the control of system management is output for management-target-process-name.

(S)
Continues processing.

KNAD3620-E

The user does not have permission to execute the command executed-command-name.

A user that does not have administrator permissions attempted to execute the command.

(S)
Does not execute the command.

(O)
A user that has administrator permissions must execute the command.

KNAD3621-E

A fork system call failed during initialization: JP1/AJS3

A fork system call to be executed in the background failed when system management started.

(S)
Terminates system management.

(O)
Check whether there is a system memory shortage. Also check whether OS operation is normal.

KNAD3623-E

The setsid function failed. (error-details)

A setsid system call failed.

(S)
Terminates system management.

(O)
Check whether there is a system memory shortage. Also check whether OS operation is normal.

KNAD3624-E

An attempt to create a process management table has failed.

An attempt to create a system management table has failed.

(S)
Terminates the system management command.

(O)
  • Check whether there is a system memory shortage and whether the product has been installed correctly.
  • Check whether the settings in the extended startup process definition file (jp1xx_service_0700.conf) have been specified correctly. The jp1xx part of the file name is jp1ajs.
  • Make sure that all processes that were managed last time have terminated normally and none of the processes remain in the system.
  • If any managed processes remain, forcibly terminate all of them, and then restart the service.
  • Check whether the KAVS2128-E message was output to the Windows event log (in Windows) or syslog (in UNIX).
  • If the KAVS2128-E message was output, setup of the scheduler service has failed, in which case take the corrective action suggested in the message.

KNAD3625-E

An internal error occurred. Execution Command names differ. executed-command-name

executed-command-name does not match.

(S)
Terminates system management.

(O)
Use the data collection tool to collect data, and then contact the system administrator.

KNAD3626-E

An attempt to create a lock file has failed. lock-file-path-error-details

An attempt to create a lock file has failed.

(S)
Terminates the system management command.

(O)
Check whether there is a conf directory and whether it has read and write permissions. For cluster operation, check whether a conf directory is defined and whether it has read and write permissions.

KNAD3627-I

JP1/AJS3 is already running.

The service to be started is already running.

(S)
Terminates the system management command.

KNAD3631-E

build_proc_table : The return value NULL was returned to the getfield function. preset-value

An entry in the extended startup process definition file (jp1xx_service_0700.conf) has not been set correctly. The jp1xx part of the file name is jp1ajs.

(S)
Terminates system management.

(O)
Make sure that the entry in the extended startup process definition file has been set correctly.

KNAD3638-E

process-name : Memory allocation failed : return-code

An attempt to allocate memory for the operation has failed.

(S)
Terminates system management.

(O)
Check whether there is a memory shortage.

KNAD3642-E

An internal error occurred. Component names differ. JP1/AJS3

Component names do not match.

(S)
Terminates system management.

(O)
Use the data collection tool to collect data, and then contact the system administrator.

KNAD3643-E

An attempt to open the environment definition file file-name has failed.

The environment definition file could not be opened.

(S)
Terminates system management.

(O)
Check whether the product has been installed correctly.

KNAD3644-E

An attempt to expand the environment variables has failed.

An attempt to read environment variables from jp1xx_env.conf has failed. The jp1xx part of the file name is jp1ajs.

(S)
Terminates system management.

(O)
Check whether there is a system memory shortage.

KNAD3645-I

The logical hostname for system management is logical-host-name.

System management by the logical host has started.

(S)
Continues processing.

KNAD3646-I

The option-name option is specified.

System management has started with an option.

(S)
Continues processing.

KNAD3647-E

The expiration of the time limit. JP1/AJS3

The time limit for the JP1/AJS3 test version has expired.

(S)
Cancels processing.

KNAD3649-E

The environment variable of JP1_HOSTNAME is empty.

The JP1_HOSTNAME environment variable setting is not correct.

(S)
Terminates the system management command.

(O)
Either set a correct logical host name in the JP1_HOSTNAME environment variable, or delete the JP1_HOSTNAME environment variable.

KNAD3650-I

JP1/AJS3 start up the management-target-process-name.

Startup processing of the process managed by system management is being performed. management-target-process-name is the name of the process configured from all the components under the control of system management.

(S)
System management starts for the management-target process.

KNAD3651-I

Startup processing for JP1/AJS3 has started.

System management is performing startup processing for a process under management.

(S)
System management starts the process under management.

KNAD3652-E

A timeout occurred during the wait for a response. (timeout period = timeout-in-seconds seconds)

A timeout occurred during the wait for a response.

(S)
Terminates the system management command.

(O)
Change the timeout value, and then retry the operation.

KNAD3653-E

An attempt to send a request to the system management has failed.

Communication with system management from the system management command has failed.

(S)
Terminates the system management command.

(O)
The process might be terminating. Wait a while, and then re-execute the command. In UNIX, make sure that the /var/opt/jp1ajs2/tmp directory exists.

KNAD3654-E

An attempt to receive a response from the system management has failed.

The system management command was unable to receive data from system management.

(S)
Terminates the system management command.

(O)
Restart system management, and then retry the operation.

KNAD3655-E

Invalid data was received from the system management.

The system management command has received invalid data from system management.

(S)
Terminates the system management command.

(O)
Temporary reception of invalid data might have occurred. Restart system management, and then retry the operation.

KNAD3656-I

The startup command terminated normally.

The command that starts system management has terminated normally.

(S)
Terminates the system management command.

KNAD3657-E

The startup command terminated abnormally

The startup command has terminated abnormally.

(S)
Terminates the system management command.

(O)
Use the jajs_spmd_status command to check the command status, and then retry the operation.

KNAD3658-E

The startup command terminated abnormally due to an inconsistent state.

This message is output when a command is executed while system management is performing other processing.

(S)
Terminates the system management command.

(O)
After waiting a while, use jajs_spmd_status command to check the status, and then retry the operation.

KNAD3659-I

There were no processes that could run.

There is no process that can be started.

(S)
Terminates the system management command.

KNAD3660-E

Invalid data was received. : maintenance-information

The system management command has received invalid data from system management.

(S)
Terminates the system management command.

(O)
Temporary reception of invalid data might have occurred. Restart system management, and then retry the operation.

KNAD3661-E

An unexpected result code was received. (return code = return-code)

The system management command has received an invalid result code from system management.

(S)
Terminates the system management command.

(O)
Use jajs_spmd_status command to check the status, and then retry the operation.

KNAD3662-I

The system management is not running.

System management is not running.

(S)
Terminates the system management command.

KNAD3663-E

Execute the command from the administrator console.

This command must be executed from the command prompt window opened by a user with administrator permissions or from the JP1/Base administrator console.

(S)
Terminates the command processing.

(O)
Re-execute the command for the command prompt window opened by a user with administrator permissions or from the JP1/Base administrator console.

KNAD3669-E

Specified Scheduler service does not exist.

The specified scheduler service was not found.

(S)
Terminates the system management command.

(O)
Correctly specify the scheduler service to be used for the processing, and then re-execute the command.

KNAD3670-I

JP1/AJS3 start the schedule stop.

Planned termination processing for the process managed by system management has started.

This message is output when JP1/Power Monitor is linked.

(S)
Terminates the system management command.

KNAD3671-I

JP1/AJS3 start the jobnet restriction stop.

Restricted termination processing of jobnets for the process managed by system management has started.

This message is output when JP1/Power Monitor is linked.

(S)
Terminates the system management command.

KNAD3672-I

A forced termination (kill) of JP1/AJS3 has started.

Processing to force termination of system management has started.

(S)
Terminates the system management command.

KNAD3673-I

JP1/AJS3 start the cancel of stop request.

Processing to cancel the termination of the process managed by system management has started.

This message is output when JP1/Power Monitor is linked.

(S)
Terminates the system management command.

KNAD3674-I

Termination processing of JP1/AJS3 has started.

Termination processing for system management has started.

(S)
Terminates the system management command.

KNAD3675-I

The stop command terminated normally.

The command that terminates system management has terminated normally.

(S)
Terminates the system management command.

KNAD3676-E

The stop command terminated abnormally.

The termination command has terminated abnormally.

(S)
Terminates the system management command.

(O)
After waiting a while, use the jajs_spmd_status command to check the status, and then retry the operation.

KNAD3677-E

The stop command terminated abnormally due to an inconsistent state.

A command was executed while system management was performing other processing.

(S)
Terminates the system management command.

(O)
Wait a while, and then re-execute the operation.

KNAD3678-I

There were no processes that could terminate.

No processes that can be stopped were found.

(S)
Terminates the system management command.

KNAD3680-I

Reload processing for JP1/AJS3 has started.

Reload processing for the process managed by system management has started.

(S)
Terminates the system management command.

KNAD3681-I

The reload command terminated normally.

The command that reloads system management has terminated normally.

(S)
Terminates the system management command.

KNAD3682-E

The reload command terminated abnormally.

The reload command has terminated abnormally.

(S)
Terminates the system management command.

(O)
Check the processes under management for whether there is a process for which reloading was unsuccessful.

KNAD3683-E

The reload command terminated abnormally due to an inconsistent state.

A command was executed while system management was performing other processing.

(S)
Terminates the system management command.

(O)
Wait a while, and then re-execute the operation.

KNAD3684-E

There were no processes that could be reloaded.

No processes that can be reloaded were found.

(S)
Terminates the system management command.

(O)
Check whether any processes under management are running.

KNAD3685-E

A timeout occurred in process-name.

The reload processing for the process indicated by process-name timed out.

(S)
Terminates the system management command.

(O)
Check whether there is a process under management for which reloading was unsuccessful.

KNAD3686-E

Shared memory is not available. return code = return-code

An attempt to secure shared memory has failed.

(S)
Terminates the system management command.

(O)
Probable causes are listed below. Check the environment.
  • Check the integrated trace log. If an error message related to an environment setting parameter has been output, review the environment setting parameter, and then retry the operation.
  • For UNIX, review the kernel parameter for whether the size allocated for shared memory is correct.
  • If you cannot solve the problem, use the data collection tool to collect data, and then contact the system administrator.

KNAD3687-E

Specified data format is not acceptable for the environment variable. : value

There is a problem with the specification of the environment variable.

(S)
Terminates the system management command.

(O)
Specify the environment setting correctly, and then re-execute the command. For details about environment variables, see 1.4 Environment variables in the manual Job Management Partner 1/Automatic Job Management System 3 Command Reference 1.

KNAD3690-I

Processing to report the status of JP1/AJS3 has started.

Processing that reports the status of system management has started.

(S)
Terminates the system management command.

KNAD3691-I

All the processes have started.

All processes under management have started.

(S)
Terminates the system management command.

KNAD3692-I

Some of the processes have started.

Some of the processes under management have started.

(S)
Terminates the system management command.

KNAD3693-I

All of the processes have stopped.

All processes under management have stopped.

(S)
Terminates the system management command.

KNAD3694-I

Part of the process is now restarting.

System management has partially restarted.

(S)
Terminates the command reporting the system management status.

KNAD3695-E

Invalid value for option (option-name).

There is a problem with the option value.

(S)
Terminates the system management command.

(O)
Specify the option value correctly, and then re-execute the command.

KNAD3705-I

management-target-process-name is now starting. (process ID = process-ID)

A process under management will start. management-target-process-name is the name of a process configured from all components under the control of system management. process-ID is the process ID of the process that has started.

(S)
Continues processing.

KNAD3732-I

JP1/AJS3 detected the termination of management-target-process-name. (process ID = process-ID)

Stopping of a process under management has been detected. management-target-process-name is the name of a process configured from all components under the control of system management. process-ID is the process ID of a running process.

(S)
Continues processing.

KNAD3736-I

All processes of JP1/AJS3 have stopped.

All processes under management have stopped.

(S)
Terminates system management.

KNAD3737-E

The JP1/AJS3 management-target-process-name terminated abnormally.

Abnormal termination of a process under management has been detected. management-target-process-name is the name of a process configured from all components under the control of system management.

(S)
Continues processing.

(O)
Check the integrated trace log for data output for the process under management that terminated abnormally, and remove the cause of the problem. Next, use the jajs_spmd_status command to check the command status, and then restart the operation.
If the process under management has not output a message, use the data collection tool to collect data, and then contact the system administrator.
Note also that output of this error message might depend on whether "1 (Restart)" is specified for the restart option in the extended startup process definition file. For details about causes and actions, see 7.3.1 Restarting an abnormally terminated JP1/AJS3 process in the Job Management Partner 1/Automatic Job Management System 3 Administration Guide.

KNAD3743-I

JP1/AJS3 has terminated.

System management has terminated.

(S)
Terminates system management.

KNAD3744-I

JP1/AJS3 startup has finished.

Service startup has been completed.

(S)
Continues processing.

KNAD3745-I

The JP1/AJS3 startup request has finished.

A startup request has been completed.

(S)
Continues processing.

KNAD3746-I

The JP1/AJS3 management-target-process-name terminated.

A process under JP1/AJS3 management has terminated.

The name of a process configured from all components under the control of system management is output for management-target-process-name.

(S)
Continues processing.

KNAD3751-E

The process stopped in response to the signal. pid = process-ID. signal = signal-number.

A process under management has stopped in response to a signal. process-ID is the process ID of a running process under management. signal-number is the signal number that caused the stoppage.

(S)
Continues processing.

(O)
Check the integrated trace log for data output for the process under management that terminated abnormally, and remove the cause of the problem. Next, use the jajs_spmd_status command to check the command status, and then restart the operation.
If the process under management has not output a message, use the data collection tool to collect data, and then contact the system administrator.

KNAD3752-E

An attempt to start management-target-process-name has finished. (return code = return-code, detail code = reason-code)

An attempt to start a process under management has failed. management-target-process-name is the name of a process configured from all components under the control of system management.

(S)
Continues processing.

(O)
Use the data collection tool to collect data, and then contact the system administrator.

KNAD3753-E

An attempt to stop management-target-process-name has finished. (return code = return-code detail code = reason-code)

An attempt to stop a process under management has failed. management-target-process-name is the name of a process configured from all components under the control of system management.

(S)
Continues processing.

(O)
Use the data collection tool to collect data, and then contact the system administrator.

KNAD3757-E

An attempt to read the product information failed. (Detailed information: detailed-information)

An attempt to read the product information has failed.

(S)
Cancels processing.

(O)
If the system time has been set to a value earlier than the installation time, restore the time, and then retry the operation.
For any other case, perform an overwrite installation, and then retry the operation.
If this message was output after an overwrite installation, uninstall the product, and then retry the operation.

KNAD3759-E

A function-name system call failed. return-code

A function-name system call has failed.

(S)
Terminates system management.

(O)
Check whether there is a system memory shortage. Also check whether OS operation is normal.

KNAD3760-I

The changes to file-name were not applied.

The changes to the settings in the extended startup process definition file (jp1xx_service_0700.conf) have not been applied. The jp1xx part of the file name is jp1ajs.

(S)
Continues processing.

(O)
Change the settings, and then retry the operation.

KNAD3761-E

In the file file-name, the restart-or-not value is invalid. ( restart-or-not = preset-value)

The value specified for the restart option in the extended startup process definition file (jp1xx_service_0700.conf) is invalid. The jp1xx part of the file name is jp1ajs.

(S)
Continues processing.

(O)
Change the set value, and then retry the operation.

KNAD3762-I

Set 0 or 1 for the restart-or-not value.

The value specified for the restart option in the extended startup process definition file (jp1xx_service_0700.conf) must be set to 0 or 1. The jp1xx part of the file name is jp1ajs.

(S)
Continues processing.

(O)
Set the value of the restart option to 0 or 1.

KNAD3763-E

In the file file-name, the number-of-restarts value is invalid. (restart num. = preset-value)

The value specified for number of restarts in the extended startup process definition file (jp1xx_service_0700.conf) is invalid. The jp1xx part of the file name is jp1ajs.

(S)
Continues processing.

(O)
Change the set value, and then retry the operation.

KNAD3764-I

Set 0 to 99 for the number-of-restarts value.

The value specified for number of restarts in the extended startup process definition file (jp1xx_service_0700.conf) must be a value from 0 to 99. The jp1xx part of the file name is jp1ajs.

(S)
Continues processing.

(O)
Set the value for number of restarts to a value from 0 to 99.

KNAD3765-E

In the file file-name, the restart interval value is invalid. (restart interval = preset-value)

The value specified for the retry interval in the extended startup process definition file (jp1xx_service_0700.conf) is invalid. The jp1xx part of the file name is jp1ajs.

(S)
Continues processing.

(O)
Change the set value, and then retry the operation.

KNAD3766-I

Set 0 to 3600 for the restart interval value.

The value specified for the retry interval in the extended startup process definition file (jp1xx_service_0700.conf) must be a value from 0 to 3,600. The jp1xx part of the file name is jp1ajs.

(S)
Continues processing.

(O)
Set the value of the retry interval to a value from 0 to 3,600.

KNAD3767-E

In the file file-name, the restart-count reset time is invalid. (restart-count reset time = preset-value)

The value specified for the reset time for the number of restarts in the extended startup process definition file (jp1xx_service_0700.conf) is invalid. The jp1xx part of the file name is jp1ajs.

(S)
Continues processing.

(O)
Change the set value, and then retry the operation.

KNAD3768-I

Set 3600 to 2147483647 for the restart-count reset time.

The value specified for the reset time for the number of restarts in the extended startup process definition file (jp1xx_service_0700.conf) must be a value from 3,600 to 2,147,483,647. The jp1xx part of the file name is jp1ajs.

(S)
Continues processing.

(O)
Set the value for the reset time for the number of restarts to a value from 3,600 to 2,147,483,647.

KNAD3769-I

In file-name, check the entries: process-name|path|startup-option|restart-or-not|number-of-restarts|restart-interval|restart-count-reset-time|kind|scheduler-flag|start-order|auto-start|stop-path|stop-option|check-status-path|check-status-option|check-status-end|check-status-interval|

Verify the entries in the extended startup process definition file (jp1xx_service_0700.conf). The jp1xx part of the file name is jp1ajs.

(S)
Continues processing.

(O)
Verify the entries in the extended startup process definition file.
If jp1ajs_spmd.conf has already been customized to enable the linkage function, make sure that the process that is an entry in jp1ajs_spmd.conf is also an entry in the extended startup process definition file (jp1ajs_service_0700.conf).
If the entry is missing, view the model file (model appears at the end of the file name) and copy the entry for the corresponding process into the extended startup process definition file.

KNAD3777-I

JP1/AJS3: The stopped management-target-process-name will be restarted. (restart count = restart-count)

The process under management that has stopped will be restarted. management-target-process-name is the name of a process configured from all components under the control of system management.

(S)
Restarts the process under management.

KNAD3778-I

JP1/AJS3: A startup request was sent to the process management-target-process-name.

A startup request has been sent to a process under management. management-target-process-name is the name of a process configured from all components under the control of system management.

(S)
Continues processing.

KNAD3779-I

JP1/AJS3: An attempt to send a startup request to the processmanagement-target-process-namefailed.

An attempt to send a request to start a process under management has failed. management-target-process-name is the name of a process configured from all components under the control of system management.

(S)
Continues processing.

KNAD3786-E

To process child-process-ID-of-management-target-process, the system sent the signal signal.

A signal has been sent to a child process of a process under management. child-process-ID-of-management-target-process is the process ID of the process created by the running process under management.

(S)
Continues processing.

KNAD3788-E

JP1/AJS3: The number of restarts of management-target-process-name exceeded the specified restart count.

The number of restarts for the process under management has exceeded the setting. management-target-process-name is the name of a process configured from all components under the control of system management.

(S)
Continues processing.

(O)
Check the integrated trace log for data output for the process under management that terminated abnormally, and remove the cause of the problem. Next, use the jajs_spmd_status command to check the command status, and then restart JP1/AJS3.
If this message is still output after the cause of the problem has been removed, a restart might have failed due to too short a retry interval for the managed process. See 7.3.1 Restarting an abnormally terminated JP1/AJS3 process in the Job Management Partner 1/Automatic Job Management System 3 Administration Guide, and then adjust the retry interval. If the managed process has not output a message or if there is no problem with the retry interval, use the data collection tool to collect data, and then contact the system administrator.

KNAD3792-E

JP1/AJS3 jajs_xxxd: A start parameter is invalid: Usage

A startup parameter is invalid.

jajs_xxxd is one of the following:

  • jajs_spmd: System management
  • jajs_hstd: Host service

(S)
Terminates system management.

(O)
Check the startup parameter, and then retry the operation.

KNAD3802-W

The system manager will not be monitored because an attempt to initialize the health check function failed.

System management will not be monitored because an attempt to initialize the health check function was unsuccessful.

(S)
Continues processing.

(O)
You must restart system management if you want to use the health check function to monitor system management.

KNAD3846-I

JP1/AJS3 completed the reload request.

Reload processing has been completed.

(S)
Continues processing.

KNAD3855-I

The process management-target-process-name will be terminated by SIGKILL. (process ID = process-ID)

SIGKILL has been sent to a process under management. management-target-process-name is the name of a process configured from all components under the control of system management. process-ID is the process ID of a running process under management.

(S)
Continues processing.

KNAD3862-E

JP1/AJS3: No processes could be started.

No processes under management could be started.

(S)
Terminates system management.

(O)
Check whether there is a system memory shortage and whether the product has been installed correctly.

KNAD3863-E

JP1/AJS3: No processes can be reloaded.

There were no processes under management that could be reloaded.

(S)
Continues processing.

(O)
Wait a while, and then re-execute the operation.

KNAD3870-E

The conf directory path cannot be obtained from the common definition.

An attempt to obtain the conf directory path from the common definition has failed.

(S)
Terminates the system management command.

(O)
This situation occurs because the common definition information has not been set yet. Check whether the settings are correct.

For cluster operation
Check whether the logical host name specified in the argument of the system management command is correct. Also check whether the logical host name specified in the JP1_HOSTNAME environment variable is correct. Also, setup for cluster operation as described in either of the following manuals is required: Job Management Partner 1/Base User's Guide or Job Management Partner 1/Automatic Job Management System 3 Configuration Guide 1. Make sure that one or the other has been performed.

Operation other than cluster operation
Make sure that the JP1_HOSTNAME environment variable is set for no startup. If the JP1_HOSTNAME environment variable has not been set, perform the following recovery operation.
  • For Windows
    Perform a version-upgrade installation.
  • For UNIX
    Execute the jp1ajs2_setup command.

KNAD3871-E

The conf directory path cannot be obtained by using the specified logical hostname.

An attempt to obtain the conf directory path from the common definition under the specified logical host name has failed.

(S)
Terminates the system management command.

(O)
The prerequisite is cluster operation. Make sure that the specified logical host name is correct or that setup has terminated normally.

KNAD3872-E

The log directory path cannot be obtained from the common definition information.

An attempt to obtain the log directory path from the common definition has failed.

(S)
Terminates the system management command.

(O)
For cluster operation, make sure that the logical host name setting is correct or that setup has terminated normally. For operation other than cluster operation, perform the following recovery operation.

For UNIX
Execute the setup command.

For Windows
Perform a rectification installation.

KNAD3873-E

The log directory path cannot be obtained by using the specified logical hostname.

An attempt to obtain the log directory path from the common definition under the specified logical host name has failed.

(S)
Terminates the system management command.

(O)
The prerequisite is cluster operation. Make sure that the specified logical host name is correct or that setup has terminated normally.

KNAD3874-E

HNTRLib could not be initialized.

HNTRLib2 could not be initialized. No logs will be output.

(S)
Continues processing.

(O)
If system management is running, stop it and then restart it.

KNAD3875-E

HNTRLib could not be initialized.

HNTRLib2 could not be initialized. No logs will be output.

(S)
Continues processing.

(O)
If system management is running, stop it and then restart it.

KNAD3876-E

In the file file-name, In the file %s, the kind value is invalid. (kind = preset-value)

The value specified for kind in the extended startup process definition file (jp1xx_service_0700.conf) is invalid. The jp1xx part of the file name is jp1ajs.

(S)
Continues processing.

(O)
Change the set value, and then retry the operation.

KNAD3877-I

Set 0 - 2 for the kind value.

The value specified for kind in the extended startup process definition file (jp1xx_service_0700.conf) must be 0, 1, or 2. The jp1xx part of the file name is jp1ajs.

(S)
Continues processing.

(O)
Set the value for kind to 0, 1, or 2.

KNAD3878-E

In the file file-name, In the file %s, the scheduler-flag value is invalid. (scheduler-flag = preset-value)

The value specified for the scheduler flag in the extended startup process definition file (jp1xx_service_0700.conf) is invalid. The jp1xx part of the file name is jp1ajs.

(S)
Continues processing.

(O)
Change the set value, and then retry the operation.

KNAD3879-I

Set 0 - 2 for the scheduler-flag value.

The value specified for the scheduler flag in the extended startup process definition file (jp1xx_service_0700.conf) must be 0, 1, or 2. The jp1xx part of the file name is jp1ajs.

(S)
Continues processing.

(O)
Set the value for the scheduler flag to 0, 1, or 2.

KNAD3880-E

In the file file-name, In the file %s, the scheduler-flag value is invalid. (scheduler-flag = preset-value)

The value specified for the scheduler flag in the extended startup process definition file (jp1xx_service_0700.conf) is invalid. The jp1xx part of the file name is jp1ajs.

(S)
Continues processing.

(O)
Change the set value, and then retry the operation.

KNAD3899-E

The work directory path cannot be acquired from the common definition information. (return code = return-code)

An attempt to acquire the work directory path from the common definition has failed.

(S)
Terminates the system management command.

(O)
For cluster operation, make sure that the logical host name setting is correct or that setup has terminated normally. For operation other than cluster operation, perform the following recovery operation.

For Windows
Perform a rectification installation.

For UNIX
Execute the setup command.

KNAD3905-I

A stop request was sent to the process management-target-process-name. (process ID = process-ID)

A stop request has been sent to a process under management. management-target-process-name is the name of a process configured from all components under the control of system management. process-ID is the process ID of a running process under management.

(S)
Continues processing.

KNAD3908-I

A reload request was sent to the process management-target-process-name. (process ID = process-ID)

A reload request has been sent to a process under management. management-target-process-name is the name of a process configured from all components under the control of system management. process-ID is the process ID of a running process under management.

(S)
Continues processing.

KNAD3910-I

SIGTERM will terminate the process management-target-process-name. (process ID = process-ID)

SIGTERM has been sent to a process under management. management-target-process-name is the name of a process configured from all components under the control of system management. process-ID is the process ID of a running process under management.

(S)
Continues processing.

KNAD3911-E

The system management daemon is busy.

The command is being processed.

(S)
Terminates the system management command.

(O)
Wait a while, and then re-execute the operation. If, during the startup, stop, or reload processing, output has occurred after execution of the jajs_spmd, jajs_spmd_stop, or jajs_spmd_reload command, wait until the processing has finished, and then retry the operation.

KNAD3912-I

The process is running.

(S)
Terminates the system management command.

KNAD3913-I

The process is not running.

(S)
Terminates the system management command.

KNAD3914-E

An attempt to open the lock file under the conf directory has failed.

An attempt to open the lock file in the conf directory has failed.

(S)
Terminates the system management command.

(O)
Check whether there is a conf directory and whether it has write permission.
For cluster operation, check whether there is a defined conf directory and whether it has write permission.

KNAD3935-E

create_pre_process_entry: Memory allocation failed. (request-code)

An attempt to create a startup preprocessing management table has failed. Startup preprocessing has not been performed.

(S)
Continues processing.

(O)
Check whether there is a memory shortage.

KNAD3953-E

Startup preprocessing for JP1/AJS3 has failed. (preprocessing name = startup-preprocessing-name)

Startup preprocessing has failed.

(S)
Continues processing.

(O)
Check the contents of the JP1/AJS3 advanced startup process definition file (jp1ajs_spmd_pre.conf).

KNAD3960-I

Startup preprocessing is being performed.

Startup preprocessing for system management is in progress.

(S)
Terminates the command that reports the system management status.

KNAD3961-E

The request could not be accepted because startup preprocessing is being performed.

System management could not accept a command request because startup preprocessing was being performed.

(S)
Terminates the system management command.

(O)
Wait a while, and then re-execute the operation.

KNAD3970-E

The JP1/AJS3 cannot start because the JP1/AJS3 is running in the system block.

JP1/AJS3 could not be started because the system is blocked.

(S)
Terminates the system management command.

(O)
Wait for JP1/AJS3 setup to be completed, and then restart the operation.

KNAD3971-E

The JP1/AJS3 cannot start because status unknown. Termination code = end-code

JP1/AJS3 could not be started because the system status could not be acquired.

(S)
Terminates the system management command.

(O)
Check whether JP1/AJS3 has been correctly installed, wait for setup to be completed, and then retry the operation.

KNAD3972-E

The JP1/AJS3 cannot start individually because the JP1/AJS3 is not running.

If JP1/AJS3 has stopped, separate startups are not possible.

(S)
Terminates the system management command.

(O)
Start JP1/AJS3, and then retry the operation.

KNAD3973-E

The JP1/AJS3 cannot start by command.

If JP1/AJS3 has stopped, separate startups are not possible.

(S)
Terminates the system management command.

(O)
JP1/AJS3 must be executed from the service side.

KNAD3981-I

jajs_xxxd_stop -job: A request to stop job restrictions will be sent to all processes of JP1/AJS3.

A request to stop job restrictions was sent to all processes under management.

jajs_xxxd is one of the following:

  • jajs_spmd: System management
  • jajs_dbmd: DB service
  • jajs_hstd: Host service
  • jajs_agtd: Agent service
  • jajs_schd: Scheduler service

(S)
Continues processing.

KNAD3984-I

A request to stop job restrictions has been sent to the process management-target-process-name. (process ID = process-ID)

management-target-process-name is the name of a process configured from all components under the control of system management. process-ID is the process ID of a running process under management.

(S)
Continues processing.

KNAD3985-I

JP1/AJS3 start the job restriction stop of management-target-process-name.

Processing to stop job restrictions for the process managed by system management has started. management-target-process-name is the name of the process configured from all the components under the control of system management.

(S)
Terminates the system management command.

KNAD3986-I

Processing to stop JP1/AJS3 job restrictions has started.

Processing to stop job restrictions in system management has started.

(S)
Terminates the system management command.

[Contents][Back][Next]

[Trademarks]

Copyright (C) 2009, 2010, Hitachi, Ltd.
Copyright (C) 2009, 2010, Hitachi Solutions, Ltd.