KFAA50064-E


      
         The worker node cannot be added to the multi-node configuration.

         
            
               aa....aa:

               
                  Cause of the error

               

            
            
               S:

               
                  Terminates processing.

               

            
            
               Action:

               
                  Take corrective action for the cause of the error displayed for aa....aa.

                  

                        
                        
                        
                        
                           
                              
                                 Display of aa....aa

                              

                              
                                 Cause of the error

                              

                              
                                 Corrective action to take

                              

                           

                        

                        
                           
                              
                                 one of the HADB servers that composes the multi-node configuration is performing termination processing

                              

                              
                                 One of the HADB servers in the multi-node configuration is performing termination processing.

                              

                              
                                 Wait for completion of termination processing of the HADB server, and then perform the operation to add the worker node.

                              

                           

                           
                              
                                 the primary node is performing switchover processing

                              

                              
                                 Primary node switchover processing is in progress.

                              

                              
                                 Wait for completion of primary node switchover processing, and then perform the operation to add the worker node.

                              

                           

                           
                              
                                 another HADB server is being returned to the multi-node configuration

                              

                              
                                 Another node is being returned to the multi-node configuration.

                              

                              
                                 Wait for completion of processing to return to the multi-node configuration, and then perform the operation to add the worker node.

                              

                           

                           
                              
                                 no more worker nodes can be added

                              

                              
                                 An attempt was made to add more worker nodes than the maximum number of worker nodes.

                              

                              
                                 After deleting the other worker nodes, execute the operation to add a worker node.

                                 This message is also output when a worker node is added to a multi-node configuration without specifying the adb_sys_multi_max_worker_nodes operand in the server definition for the primary and secondary nodes. In this case, terminate the HADB server in the multi-node configuration once and specify the adb_sys_multi_max_worker_nodes operand in the server definition for the primary node and each secondary node. Then, start the HADB servers in the multi-node configuration and execute the operation to add a worker node.

                              

                           

                           
                              
                                 the adbmodarea command is being executed on the primary node

                              

                              
                                 The adbmodarea command is being executed on the primary node.

                              

                              
                                 Wait for the completion of the adbmodarea command executing on the primary node.

                                 Note that the DB directory configuration has been changed by executing the adbmodarea command. Therefore, execute the adbinit command to make the DB directory configuration the same as the primary node, and then execute the operation to add the worker node. For details on how to create the initialization option used when executing the adbinit command, see Notes on executing the adbinit command when adding a new secondary node in the manual HADB Setup and Operation Guide. When reading this section, replace the secondary node with a worker node.

                              

                           

                           
                              
                                 the adbupddmk command is being executed on the primary node

                              

                              
                                 The adbupddmk command is being executed on the primary node.

                              

                              
                                 Wait for the completion of the adbupddmk command executing on the primary node. Then, execute the operation to add a worker node.

Display of aa....aa	Cause of the error	Corrective action to take
one of the HADB servers that composes the multi-node configuration is performing termination processing	One of the HADB servers in the multi-node configuration is performing termination processing.	Wait for completion of termination processing of the HADB server, and then perform the operation to add the worker node.
the primary node is performing switchover processing	Primary node switchover processing is in progress.	Wait for completion of primary node switchover processing, and then perform the operation to add the worker node.
another HADB server is being returned to the multi-node configuration	Another node is being returned to the multi-node configuration.	Wait for completion of processing to return to the multi-node configuration, and then perform the operation to add the worker node.
no more worker nodes can be added	An attempt was made to add more worker nodes than the maximum number of worker nodes.	After deleting the other worker nodes, execute the operation to add a worker node. This message is also output when a worker node is added to a multi-node configuration without specifying the adb_sys_multi_max_worker_nodes operand in the server definition for the primary and secondary nodes. In this case, terminate the HADB server in the multi-node configuration once and specify the adb_sys_multi_max_worker_nodes operand in the server definition for the primary node and each secondary node. Then, start the HADB servers in the multi-node configuration and execute the operation to add a worker node.
the adbmodarea command is being executed on the primary node	The adbmodarea command is being executed on the primary node.	Wait for the completion of the adbmodarea command executing on the primary node. Note that the DB directory configuration has been changed by executing the adbmodarea command. Therefore, execute the adbinit command to make the DB directory configuration the same as the primary node, and then execute the operation to add the worker node. For details on how to create the initialization option used when executing the adbinit command, see Notes on executing the adbinit command when adding a new secondary node in the manual HADB Setup and Operation Guide. When reading this section, replace the secondary node with a worker node.
the adbupddmk command is being executed on the primary node	The adbupddmk command is being executed on the primary node.	Wait for the completion of the adbupddmk command executing on the primary node. Then, execute the operation to add a worker node.