mmm a failure has occurred in the session. connection name=aa...aa logical terminal name=bb...bb reason code=cc...cc

mmm: MCF identifier

aa...aa: Connection name

bb...bb: Logical terminal name

cc...cc: Reason code

016001xx: An IOA failure was detected by IO_INT.

xx: estat-dep value in clist

016002xx: An IOA failure was detected by IO_INT.

xx: estat-dep value in failt_clist

016003xx: An IOA failure was detected by BA_INT.

xx: estat-dep value in the IO_STATUS register

016004xx: An MBA failure was detected by BA_INT.

xx: Error reason code for kernel notification

01600500: This is an HPM failure.

016007xx: An MCI failure (with SCSI-SENSE) was detected by 0.

xx: The last or first byte of the sense code in the sense buffer

016008xx: An IOA failure was detected by IO_INT.

xx: The last byte of the reason code in the sense buffer

01600900: This is a timeout occurring while waiting for a CLIST report.

01600a00: This is a timeout occurring while monitoring the ry bit.

01600b00: The sequence for CLIST reports is inconsistent.

01600c00: The term/cancel command has terminated abnormally.

01600d00: An error occurred in associ-oct-addr in the CLIST.

01600e00: An error occurred in SAVE_DMACOUNT in the CLIST.

01600f00: A CLIST-based fe failure has been detected.

01601000: The IOA definition does not match the actual hardware.

02000000: This is a normal termination.

02601020: This is an LP failure.

02601021: This is an LP failure (LC failure).

02601030: This is a line failure.

02601031: This is a link failure.

02601040: This is a format error.

02601050: This is a condition error.

02602010: This is a timeout occurring during LP monitoring.

02603020: This is a status mismatch (a request when the link is not disconnected).

02603022: This is a status mismatch (a request when the mode is not online).

02603024: This is a status mismatch (a request when the link has been disconnected).

02603026: This is a status mismatch (a request when a link is being established).

02603028: This is a status mismatch (a request when a link has been established).

0260302a: This is a status mismatch (a request when the link is being disconnected).

0260302c: This is a status mismatch (a request when a failure is being removed).

0260302f: This is a status mismatch (a request when the link is not confirmed).

02803110: The xnfoffline/xnfstop command has been executed.

02803010: VASS is invalid.

02803011: Open processing has already been completed.

03000000: The remote network was released (CI-NPDU received). However, this assumes that the reason code for CI-NPDU disconnection is 0x00 and that the code for diagnosis is 0xf1.

030f0000: The remote network was released based on a restart packet.

030f??**: The remote network was released (CI-NPDU received).

??: Reason code for CI-NPDU disconnection or RI-NPDU reset

**: Code for CI-NPDU diagnosis or RI-NPDU reset diagnosis

030fffff: The network was disconnected because the 3-minute link busy timer expired.

032000e3: A request was issued when there was no notification about ONLINEind.

034100**: This is a protocol error on the remote network.

**: Code for CI-NPDU diagnosis

03630047: The NSAP has not been opened. Alternatively, opening of an NSAP occurred for an open NSAP.

036300a3: The NL resource is insufficient.

036300e3: The link cannot be used.

036300e4: No reason is set because an NL call origination was rejected.

03810042: The parameter, window size, or packet size is invalid.

03810047: The logical channel number is incorrect. However, this assumes that the logical channel is being used in a VC or has already been specified by another higher layer.

038100a2: The virtual slot number (VASS) is incorrect. The request is a request to a VASS where no PVC is defined.

03a300a3: The maximum number of PVC connections has been exceeded.

03c400e8: The NL call origination has been rejected. The parameter (virtual slot number value) at the time of the NL call origination was incorrect.

03c100eb: The definition NSAP is incorrect.

04420001: The timer for monitoring ACTPU response has expired.

04420003: The request was rejected because a request to terminate the lower layer connection had already been received from the remote office.

04420007: HNA's lower-order subarea violates the protocol.

04420008: PU is temporarily performing stop processing.

04420009: Invalid data has been received by the PU for QLLC connection.

0442000a: The response monitor timer at the PU for QLLC connection has expired.

04620000: Release occurred as a result of the xnfoffline (PU stop) command execution.

04620004: The HNA1 resource is insufficient.

0463****: -RSP has been received for ACTPU.

****: System sense code

04640000: Release occurred as a result of the xnfoffline (SLU stop) command execution.

04640001: The timer for monitoring ACTLU response has exceeded the set time value.

0465****: -RSP has been received for ACTLU.

****: System sense code

04820005: A path has not been established with the incoming-only terminal.

04820006: An attempt to identify the remote terminal by means of XID has failed.

04c20002: PU is in the non-operational mode.

04c40002: SLU is in the non-operational mode.

7ezz****: A negative response has been received from the remote system for a request message that was sent.

****: Sense code of the received negative response

zz: Request code of the sent request message

7dzz****: -RSP has been sent to the remote system in response to a request message that was received

****: Sense code of the sent -RSP

zz: Request code of the received request message

7f010001: The receive data length is invalid (the data has exceeded the SLU send RU length).

7f010002: An attempt to acquire a receive buffer in the specified receive buffer group has failed.

7f010003: A request to send data for multiple-chain sending has been received, but the request cannot be executed because the chain usage definition is oic.

7f010004: A logon message in an undefined format has been received.

7f010005: A logon attempt with too many user ID digits has been received.

7f010006: A logon attempt with too many password ID digits has been received.

7f010007: A logoff message in an undefined format has been received.

7f020001: A failure occurred during message sending.

S: Terminates the session.

O: Contact the OpenTP1 administrator.

Countermeasure: Remove the cause for the failure shown in the reason code.