mmm rejection response was received from the terminal. connection name=aa...aa, logical terminal name=bb...bb, reason code=(cc...cc,dd...dd,ee...ee), sense code=ff...ff

mmm: MCF identifier

aa...aa: Connection name

bb...bb: Logical terminal name

cc...cc: Termination code

03000001: A line error occurred.

05000003: Contention occurred.

dd...dd: Detail information

ee...ee: Action code

The table lists the meanings of the termination codes and action codes, and describes the actions you must take.

ff...ff: Sense code in rejection response received from the terminal

0801xxxx

• The terminal received a command or a message, but there is no path between the specified LU, PU, or link and SSCP.
• The terminal received a command or message, but the PLU SLU pacing rule was violated.
• An auxiliary device (printer) is not connected, or it cannot be assigned because it is not turned on.

0802xxxx

• There is no paper in the terminal. Alternatively, an intervention request error occurred.

0805xxxx

• An attempt was made to start the session, but another session had already started or was starting.

0806xxxx

• The terminal received a command or message, but there is no resource corresponding to the specified LU, PU, or link.

0807xxxx

• A terminal resource cannot be used temporarily.

0809xxxx

• The terminal received a command or message, but the terminal's mode prevents it from receiving the commands and messages.

080axxxx

• The terminal received a BIND command, but the terminal is not connected, the power is off, or the 2050 and 3050 online terminal windows are closed.

080cxxxx

• The terminal received a command or message, but the specified procedure name is not supported.

080exxxx

• The terminal received a command or message, but the access request for the specified resource is not authorized.

0813xxxx

• When BID or a message (BB flag) was sent, it passed a message sent from the terminal. As a result, the terminal entered IN-BRACKET mode.

0814xxxx

• When the BID command was sent, the printer terminal was busy performing local printing from a video terminal.

0815xxxx

• The terminal received a BIND command, but a session was in progress.

0816xxxx

• The terminal received a command or message, but the specified function had already been stopped.

081axxxx

• The order of the requests received by the terminal is incorrect.

081bxxxx

• When BID or a message (BB flag) was sent, the terminal was busy because the operator was performing key-in operations or because local copying was being performed.

081cxxxx

• A permanent error occurred on the terminal.

0821xxxx

• The terminal received a BIND command, but the BIND parameter (session parameter) is invalid. The plupace, slupace, plurusiz, or slurusiz operand in mcft560bd of TP1/NET/HNA-560/20, or the lutype operand of mcftalccn is incorrect. Alternatively, the XNF/S-E2 address definition does not match an actual terminal.

0822xxxx

• The terminal detected a link level error.

0826xxxx

• The terminal received a message, but the specified function is not supported.

0829xxxx

• The host asked the terminal to send a message in IN-BRACKET mode, but the send right was not assigned.

082bxxxx

• The terminal received a message, but the terminal screen had already been cleared as a result of terminal power being turned on or off, a temporary error, or an operator operation (SRQ or text key input).

082cxxxx

• The terminal cannot accept the request issued from SSCP because the request exceeds the allowable resource limit.

082dxxxx

• When BID or a message (BB flag) was sent to a T-560/20HNA video terminal, the terminal was performing local copying activated by the terminal operator, or the SSCP-LU session was in test mode.

082exxxx

• When a T-560/20HNA video terminal was performing local copying activated by the host, an error requiring intervention, such as a paper-out condition, occurred.

082fxxxx

• When a T-560/20HNA video terminal was performing local copying activated by the host, a permanent error occurred on the printer.

0831xxxx

• When BID or message (BB flag) was sent, the terminal was not connected, the terminal power was off, or the 2050 and 3050 online terminal windows were closed.
• The power to the terminal and TCE or CS was turned off.
• The terminal power was turned off.
• The 2050 and 3050 online connection windows were closed.

083axxxx

• The terminal received a BIND command, but the session cannot start.

0845xxxx

• The terminal received a BIND command, but the device was not connected, the device power was off, or the 2050 and 3050 online terminal windows were closed.

084bxxxx

• A BID or message was sent, but the terminal was busy processing the graphics it had already received or it was executing a job.

084cxxxx

• The terminal received the message, but the requested resource cannot be used because of a permanent error.

1001xxxx

• The message received by the terminal contains a line control character.
• The message received by the terminal contains an FMH that cannot be interpreted.

1002xxxx

• The RU size received by the terminal exceeds the terminal buffer size.
• The terminal received an RU that is longer than the maximum RU length specified by the BIND parameter.

1003xxxx

• The message received by the terminal contains a command that is not supported by the terminal.
• The map that was specified at sending or the contents of the sent message are invalid.
• The on-demand Gaiji sense code was received from a T-560/20HNA terminal.

1005xxxx

• The message received by the terminal contains a control code, buffer address, or special character that is not supported by the terminal.
• The map that was specified at sending or the contents of the sent message are invalid.

1007xxxx

• A terminal that uses a keyboard as its main device received a message from SSCP.

2001xxxx

• The terminal received a command or message in which the HNA sequence number is incorrect.

2002xxxx

• The chain flag of the message received by the terminal conflicts with the protocol.

2003xxxx

• The bracket flag of the message received by the terminal conflicts with the protocol.

2004xxxx

• The terminal received a message although it had the send right in IN-BRACKET mode.

2005xxxx

• The terminal received a message before receiving the SDT command.
• A T-560/20HNA terminal was defined as a non-HNA terminal.

4006xxxx

• The terminal received an RQE message in a session in which RQE is not allowed.

4007xxxx

• The terminal received an RQD message in a session in which RQD is not allowed.

400dxxxx

• The terminal received a message that had the send right (CD) flag in a session in which direction conversion communication is not allowed.

400fxxxx

• The terminal received a message containing FMH in a session in which FMH is not allowed.
• MIC or LIC received by the terminal contains FMH.

8001xxxx

• An error occurred on the communication control device.

8002xxxx

• A line error, channel error, or TCE disconnection error occurred.

8003xxxx

• An LU operation disable error occurred on the terminal.

8004xxxx

• XNF/S-E2 does not define the network address of the destination address field (DAF) in the path/transfer control header (TH).

8005xxxx

• The session specified in the destination address (DAF) and sending source address (SAF) of the path/transfer control header (TH) has not yet been established.

8007xxxx

• The first segment is too short.
• The segment order is incorrect.

8008xxxx

• The terminal received an ACTLU command before receiving an ACTPU command.

8009xxxx

• The terminal received a command other than an ACTLU command before receiving the ACTLU command.

800axxxx

• Enough buffers to receive the PIUs received by the terminal cannot be allocated. As a result, not all PIUs could be received.
• The PIU length is much longer than the segment length.

800cxxxx

• The value in the data count field (DCF) of the path/transfer control header (TH) does not match the length of the actual transfer data.

800dxxxx

• Connection to a linked station was disconnected.
• An inquiry-monitoring timeout occurred in a transfer of data for which XNF/S-E2 was to perform inquiry monitoring.

800fxxxx

• The combination of the destination address (DAF) and sending source address (SAF) in the path/transfer control header (TH) is invalid.

S: If the session is starting, continues processing or ends the session. If the session is starting and a sense code for which retry is possible is used, performs a retry according to the TP1/NET/HNA-560/20 configuration definition.

O: Contact the OpenTP1 administrator.

Countermeasure: Determine the cause of the error by referring to the detail information given in the detail information list for the KFCA15404-E message and the sense code, then take appropriate action.

Termination code	Action code	Meaning/Action
03000001	00040001 10090001 100d0001 20000011	A rejection response was received from the remote terminal. Check the terminal status, then remove the cause of the error.
	100c0010	A rejection response was received from the remote terminal. Determine the cause of the error by referring to the detail information. Remove the cause of the error. If there is no system problem, enter the connection establishment command and establish the connection.
	10050002 200a0005	A rejection response was received from the remote terminal. Determine the cause of the error by referring to the detail information. Remove the cause of the error. If there is no system problem, start the session (logon input or session start command input from the terminal).
	100e0005	A rejection response was received from the remote terminal. Determine the cause of the error by referring to the detail information. Remove the cause of the error. If there is no system problem, start the session (session start command input).
05000003	00000001 00030001	Contention occurred when a message was to be sent. No action