cannot start status service because of aa...aa.

aa...aa: Reason code that indicates the contents of the error (up to 10 numerals)

0000000001: A status service definition environment error occurred.

Take action according to the previously output error message, if any. Correct the error and then restart OpenTP1.

0000000003: A status service definition error occurred.

Check the status service definition.

0000000004: There are no current status files.

Prepare a status file and then restart OpenTP1.

0000000005: Memory for allocating a table is insufficient.

Check the number of processes and then restart OpenTP1.

0000000006: Memory for allocating a buffer is insufficient.

Check the number of processes and then restart OpenTP1.

0000000007: A status file error occurred.

Take action according to the previously output error message, if any. Correct the error and then restart OpenTP1.

0000000008: An error in making the status file control record resident in the buffer occurred.

Take action according to the previously output error message, if any.

0000000009: A swapping error occurred.

Take action according to the previously output error message, if any.

0000000010: The status file has an error when stop is specified in the sts_initial_error_switch operand.

Correct the error in the status file and then restart OpenTP1.

0000000011: An error in obtaining the time at which a status file was designated for current use occurred.

Take action according to the previously output error message, if any. Correct the error and then restart OpenTP1.

0000000012: An error in setting the inter-process communication environment for starting the status service occurred.

Take action according to the previously output error message, if any. Correct the error and then restart OpenTP1.

0000000013: Inter-process communication for starting the status service failed.

Take action according to the previously output error message, if any. Correct the error and then restart OpenTP1.

0000000014: An error in obtaining definition environment information for starting the status service occurred.

Take action according to the previously output error message, if any. Correct the error and then restart OpenTP1.

0000000015: The current status file name selected by OpenTP1 is inconsistent with the logical file name specified in the sts_last_active_file operand.

In the sts_last_active_file operand, specify the newest logical current status file name of those that existed up to the previous OpenTP1, and then restart OpenTP1. If the newest active file name is correctly specified in the sts_last_active_file operand, restart is impossible. Initialize all status files (by using the stsinit command), and then restart OpenTP1.

0000000016: A state occurred in which the newest current status file of those that existed up to the previous OpenTP1 cannot be determined. However, processing cannot continue because no logical file name is specified in the sts_last_active_file operand.

In the sts_last_active_file operand, specify the newest logical current status file name of those that existed up to the previous OpenTP1, and then restart OpenTP1.

0000000017: Start processing stopped because an error occurred in the system specified in the sts_last_active_side operand when OpenTP1 was starting. OpenTP1 cannot be restarted.

Initialize all status files (by using the stsinit command), and then restart OpenTP1.

0000000018: When OpenTP1 started, an error occurred in one system of the newest current status file, used up to the previous online session. However, processing cannot continue because no system is specified in the sts_last_active_side operand.

Set a system in the sts_last_active_side operand, using a combination of the state of the current status file used during the previous online session and the error system reported by the KFCA01012-I message (issued immediately beforehand). Then restart OpenTP1.

The following table lists the valid combinations.

State of the current status file used during the previous online session		Error system displayed by KFCA01012-I	System specified in the sts_last_active_side operand to be specified to restart OpenTP1
System A	System B
ACTIVE	ACTIVE	A	B
		B	A
ACTIVE	Other than ACTIVE	A	OpenTP1 cannot be restarted.
		B	A
Other than ACTIVE	ACTIVE	A	B
		B	OpenTP1 cannot be restarted.

0000000019: A status file system cannot be created.

Proceed as indicated in the previously output error message. Correct the error, and then restart OpenTP1.

0000000020: Start processing stopped because a file error occurred during operation with no duplicate status file.

Proceed as indicated in the previously output error message. Correct the error, and then restart OpenTP1.

0000000021: Start processing stopped because an event that disabled further processing occurred during start processing of the status service.

Execute dcsetup -d to delete files under $DCDIR/spool, and then start OpenTP1.

S: Terminates OpenTP1 abnormally.

Countermeasure: Take action according to the reason code and then restart OpenTP1.